Moxa Technologies EDS-726 Series Manual

Moxa EtherDevice Switch

EDS-726 Hardware Installation Guide

Second Edition, June 2008

Reproduction without permission is prohibited.

P/N: 1802007260011

Panel Layout of EDS-726 Series

COUPLER CF

MODE

RING

PORT

COUPLER

PORT

FDX/HDX

STAT

PWR1 FAULT

MASTER

PWR2

LNK/ACT

SPEED

IM-1GSXSCIM-1GTX IM-4MSC

PWR

IM-4MST

PWR

IM-4TX

PWR

RS-232

Console

Load

Save

RELAY1

PWR1

PWR2

V1 V2 INPUT: 24VDC

DI1

V2+

V2-

V1+

V1-

DI2

RELAY2

13 1314 1515

1. System status LEDs

2. Push-button switch to select mode for Interface Module

3. Interface Module mode LEDs

4. Fast Ethernet Interface Module port LEDs

5. Terminal block for 2 power inputs,

2 DIs, and 2 DOs

6. Save and load buttons for CF card

7. Serial Console port

8. CF card socket

9. Gigabit Ethernet Module LEDs

10. Two cartridge receptors for Gigabit Ethernet Interface Modules

11. Fast Ethernet Interface Modules

12. Sockets for Fast Ethernet Interface Modules

13. DIN-Rail braces

14. Ribs for radiating heat

15. Screw holes for wall mounting kit

16. Grounding screw

Mounting Dimensions (unit = mm)

362.40

381.70

3085.00

146.47

Front View

EtherDevice Switch

EDS-726

106.63 149.15

362.40

401.00

Rear View

128.00

146.47

140.00

Side View

Gigabit Ethernet Interface Modules

Front View Side View

101.20

95.60

59.00

66.20

Fast Ethernet Interface Modules

129.8

100

Side View

Front View

DIN-Rail Mounting

The DIN-Rail attachment plates are permanently fixed to the back panel of

EDS-726. Do not attempt to remove the attachment plates, since doing so could

damage the product.

STEP 1:

Insert the top of the DIN-Rail into the

notches at the bottom of the top array

of heat radiating ribs.

STEP 2:

The bottom of the DIN-Rail will snap

into place behind the DIN-Rail

attachment plate.

DIN-Rail

brace

DIN-Rail

brace

As shown in the figure at the right,

use a flat-blade screw driver as a lever

to force the DIN-Rail attachment

plates downwards, and then pull

EDS-726 out away from the

DIN-Rail. The DIN-Rail attachment

plates have an internal spring that

keeps the attachment plate pushed

upwards.

DIN-Rail

brace

Wall Mounting (optional)

For some applications, you will find it convenient to mount EDS-726 on the

wall, as illustrated below.

STEP 1: Remove the aluminum DIN-Rail attachment plate from EDS-726’s

rear panel, and then attach the wall mounting plates, as shown in the diagram.

STEP 2:

Mounting EDS-726 on the wall requires 4 screws to ensure

that the switch does not come loose from the wall. Use the

switch, with wall mounting plates attached, as a guide to

mark the correct locations of the 4 screws. The heads of the

screws should be less than 6.0 mm in diameter, and the

shafts should be less than 3.5 mm in diameter, as shown in

the figure at the right.

6.0 mm

3.5 mm

NOTE Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw into one of

the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2 mm to allow room for

sliding the wall mount panel between the wall and the screws.

STEP 3: Once the screws are fixed in the wall, insert the four screw heads

through the large parts of the keyhole-shaped apertures, and then slide Moxa

EDS downwards, as indicated. Tighten the four screws for added stability.

EtherDevice Switch

EDS-726

EtherDevice Switch

EDS-726

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa EDS-726.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following guidelines:

yUse separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

yNOTE: Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid interference, wires with different signal

characteristics should be routed separately.

yYou can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together.

yKeep input wiring and output wiring separated.

yIt is strongly advised that you label wiring to all devices in the system when

necessary.

Grounding Moxa EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw, on the side panel of EDS-726, to the grounding surface prior to

connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface, such as a metal panel.

Wiring the Relay Contact

In this section, we explain the meaning of the two contacts used to connect the

alarm contact.

EDS-726 has two sets of relay output—relay 1 and relay 2. Each relay contact

consists of the two contacts of the terminal block on EDS-726’s top panel.

Refer to the next section for detailed instructions on how to connect the wires

to the terminal block connector, and how to attach the terminal block connector

to the terminal block receptor.

RELAY1 RELAY2 PWR1 PWR2

V2+V2-V1+

V1-

DI1

I1I2

DI2

Top View

Front View

FAULT: The two sets of relay

contacts of the 6-pin terminal block

connector are used to detect

user-configured events. The two

wires attached to the Fault contacts

form an open circuit when a

user-configured event is triggered.

If a user-configured event does not

occur, the Fault circuit will be

closed.

Wiring the Redundant Power Inputs

EDS-726 has two sets of power input—power input 1 and power input 2.The

top two contacts and the bottom two contacts of the 6-pin terminal block

connector on EDS’s top panel are used for EDS’s two digital inputs.

RELAY1 RELAY2 PWR1 PWR2

V2+V2-V1+

V1-

DI1

I1I2

DI2

Top View

Front View

STEP 1: Insert the

negative/positive DC wires into the

V-/V+ terminals.

STEP 2: To keep the DC wires

from pulling loose, use a small

flat-blade screwdriver to tighten

the wire-clamp screws on the front

of the terminal block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on EDS-726’s top panel.

Wiring the Digital Inputs

EDS-726 has two sets of digital input—DI 1 and DI 2. Each DI comprises two

contacts of the 6-pin terminal block connector on EDS’s top panel. The

terminal block is also used for EDS’s two DC inputs. Top and front views of

one of the terminal block connectors are shown here.

RELAY1 RELAY2 PWR1 PWR2

V2+V2-V1+

V1-

DI1

I1I2

DI2

Top View

Front View

STEP 1: Insert the negative

(ground)/ positive DI wires into the

┴/I1 terminals.

STEP 2: To keep the DI wires

from pulling loose, use a small

flat-blade screwdriver to tighten

the wire-clamp screws on the front

of the terminal block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on EDS-726’s top panel.

Communication Connections

The pinout and cable wiring diagrams in this section show how the ports on

EDS-726 connect to other devices:

Pinouts are diagrams that indicate the type of signal passing through each of

the port’s pins.

NOTE 1. The pin numbers for male DB9 and DB25 connectors, and hole

numbers for female DB9 and DB25 connectors are labeled on the

connector. However, the numbers are typically quite small, so you

may need to use a magnifying glass to see the numbers clearly.

2. The pin numbers for both 8-pin and 10-pin RJ45 connectors (and

ports) are typically not labeled on the connector (or port). Refer to

the Pinout diagram below to see how RJ45 pins are numbered.

RS-232 Connection

EDS-726 has one RS-232 (10-pin RJ45) console port, located on the side panel.

Use either an RJ45-to-DB9 or RJ45-to-DB25 cable to connect Moxa

EDS-726’s console port to your PC’s COM port. You may then use a console

terminal program, such as Moxa PComm Terminal Emulator or Hyper

Terminal, to access Moxa EDS-726’s console configuration utility.

10-pin RJ45 Console Pinouts

10-Pin Description

1 ------

2 DSR

3 ------

4 GND

5 TxD

6 RxD

7 GND

8 ------

9 DTR

10 ------

110

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on EDS-726’s front panel are used to

connect to Ethernet-enabled devices.

Below we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports.

MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45

Pin Signal Pin Signal

1 Tx+ 1 Rx+

2 Tx- 2 Rx-

3 Rx+ 3 Tx+

6 Rx- 6 Tx-

1000BaseT Ethernet Port Connection

1000BaseT data is transmitted on differential TRD+/- signal pairs over copper

wires.

MDI/MDI-X Port Pinouts

Pin Signal

1 TRD(0)+

2 TRD(0)-

3 TRD(1)+

4 TRD(2)+

5 TRD(2)-

6 TRD(1)-

7 TRD(3)+

8 TRD(3)-

100/1000BaseFX Ethernet Port Connection

The concept behind the SC/ST port and cable is quite straightforward. Suppose

you are connecting devices I and II. Contrary to electrical signals, optical

signals do not require a circuit in order to transmit data. Consequently, one of

the optical lines is used to transmit data from device I to device II, and the

other optical line is used to transmit data from device II to device I, for

full-duplex transmission.

All you need to remember is to connect the Tx (transmit) port of device I to the

Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx

(transmit) port of device II. If you make your own cable, we suggest labeling

the two sides of the same line with the same letter (A-to-A and B-to-B, as

shown below, or A1-to-A2 and B1-to-B2).

SC-Port Pinouts SC-Port to SC-Port Cable Wiring

Cable Wiring

A A

B B

ST-Port Pinouts ST-Port to ST-Port Cable Wiring

Cable Wiring

A A

B B

ATTENTION

This is a Class 1 Laser/LED product. To avoid causing serious

damage to your eyes, do not stare directly into the Laser Beam.

LED Indicators

The front panel of Moxa EDS-726 contains several LED indicators. The

function of each LED is described in the table below.

LED Color State Description

System LEDs

On System has passed self-diagnosis

test on boot-up and is ready to run.

GREEN Blinking System is undergoing the

self-diagnosis test.

STAT

RED On

System failed self-diagnosis on

boot-up.

On Power is being supplied to the main

module’s power input PWR1.

PWR1 AMBER Off Power is not being supplied to the

main module’s power input PWR1.

On Power is being supplied to the main

module’s power input PWR2.

PWR2 AMBER Off Power is not being supplied to the

main module’s power input PWR2.

On The corresponding PORT alarm is

enabled and a user-configured event

has been triggered.

FAULT RED

Off

The corresponding PORT alarm is

enabled and a user-configured event

has not been triggered, or the

corresponding PORT alarm is

disabled.

On This EDS-726 is the Master of this

Turbo Ring.

Blinking This EDS-726 has become Ring

Master of this Turbo Ring after the

Turbo Ring was broken.

MASTER GREEN

Off This EDS-726 is not the Master of

this Turbo Ring.

On When this EDS-726 enables the

coupling function to form a back-up

path.

COUPLER GREEN

Off When this EDS-726 disables the

coupling function.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Moxa Technologies

Moxa Technologies

Moxa Technologies TN-4516A non-PoE series Manual de usuario

Moxa Technologies

Moxa Technologies TN-5500A Series Manual de usuario

Moxa Technologies

Moxa Technologies PT-7728 Series Manual de usuario

Moxa Technologies

Moxa Technologies SPL-24 Manual de usuario

Moxa Technologies

Moxa Technologies TRC-190 Manual de usuario

Moxa Technologies

Moxa Technologies ICS-G7 Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-G2005-EL Series Manual de usuario

Moxa Technologies

Moxa Technologies IKS-6726-8PoE Series Manual

Moxa Technologies

Moxa Technologies PT-G7728 Manual de usuario

Moxa Technologies

Moxa Technologies PT-7828 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-G512E-8PoE Manual

Moxa Technologies

Moxa Technologies TN-5308-LV Manual de usuario

Moxa Technologies

Moxa Technologies EDS-G2008-EL Series Manual de usuario

Moxa Technologies

Moxa Technologies TN-5508A Series Manual

Moxa Technologies

Moxa Technologies ToughNet TN-5510-2GLSX-ODC Manual

Moxa Technologies

Moxa Technologies EDS-316 EtherDevice Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Manual de usuario

Moxa Technologies

Moxa Technologies EDS-405A Manual

Moxa Technologies

Moxa Technologies NPort 1220 Manual de usuario

Moxa Technologies

Moxa Technologies EDS-P206A-4PoE-SS-SC Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Manual

Moxa Technologies

Moxa Technologies ThinkCore DA-660-8/16-LX Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario