Mountup MU6001 Manual de usuario
Single Monitor Desk Mount
Instruction Manual
If you have any questions , please contact us.
75x75
100x100
2~8kg
4.4~17.6lbs
32"
MU6001
V2.0
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, please contact us.
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
17.6lbs
(8kg)
A (x1)
Upper Arm
B (x1)
Lower Arm
F (x1)
Clamp
I (x1)
Grommet Base
J (x1)
Wingnut
L (x1)
Bolt
K (x1)
Carriage Bolt
N (x1)
3mm Allen Key
O (x1)
4mm Allen Key
P (x1)
6mm Allen Key
G(x5)
M6x10
H(x4)
Pad
01
C (x1)
Base
M (x1)
Support Plate
M-C (x4)
D6 Washer
M-A (x4)
M4x12
M-B (x4)
M6x12 M-D (x4)
spacer
E (x1)
Bracket
D (x1)
VESA Plate
ASSEMBLY STEPS
STEP 2: Clamp Installation or Grommet Base Installation
STEP 1: Apply Pads to the Base Bottom
02
OPTION A: Clamp Installation
Mount Bracket (E) to Base Bottom (C) with Bolts (G). Bolts could be tightened by the 4mm Allen Key (O).
Similarly, attach Clamp (F) to Bracket (E) with Bolts (G) and 4mm Allen Key (O).
Adjust the Clamp width to t with desk. Secure stand to desktop by tightening Clamp (F) or by Allen key (P).
G
OO
G
10-60mm
10-90mm
F
E
F
C
EG
O
OR
H
C
Apply pads (H) to the base
bottom to avoid desk scratches.
P
OR
STEP 2: (Continued)
03
OPTION B: Grommet Base Installation
For grommet hole mounting, place Carriage Bolt (K) through the center of Grommet Base (I).
Mount Grommet Base to Base Bottom (C) with Bolts (G) and tighten by 4mm allen key (O).
Run Carriage Bolt (K) through Grommet Hole on desktop. Attach Support Plate (M) and Wingnut (J).
Last step, tighten Wingnut (J).
O
C
I
G
K
M
J
10-90mm
04
Install the lower arm (B) and the upper arm (A) to the base (C). Secure the arm by tightening the inside screw
using 3mm Allen key (N).
STEP 3: Arm Installation
F
N
N
B
A
C
Note: Please note that the side with
the label“ ” is installed on the
base(C) when installing the lower
arm(B) to the base (C).
DO NOT tighten the
screw excessively or
it might be stripped.
DO NOT tighten the
screw excessively or
it might be stripped.
05
STEP 4: Attach Monitor
D
D
M-A
M-B
M-C
P
M-A
M-B
M-C
M-D
P
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to back of monitor and
secure with screws(M-A)or(M-B) with washers(M-C)
using 6 mm Allen Key (P). Do not tighten the screws
excessively or your monitor might be damaged.
.
CAUTION:To select the correct screws(M-A or M-B)
for your monitor, you can try to screw it on your
monitor by hand. The one can screw inside is the
correct screw for your monitor.
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to back of monitor and secure
with screws (M-A) or (M-B) with washers (M-C)and
spacers(M-D)using 6 mm Allen Key (P). Do not tighten
the screws excessively or your monitor might be damaged.
06
Slide the monitor onto the head of swivel arm, install the security bolt (L). Make sure the security
bolt is installed before you rotate the monitor.
STEP 5: Hang Monitor
Tilts down
Note:
1. Loosen the tilting bolt.
2. Adjust monitor to your
desired tilting angle.
3. Retighten the tilting bolt to
P
L
Important Notice:
The gas spring is pre-set to minimum tension. Once the monitor is hanged on, hold the
monitor with both hands and DO NOT let go suddenly or immediately. Instead, leave the
monitor in a slow & gentle way while observing whether the arms will fall down wildly.
Guideline to adjust monitor tilting angle.
07
STEP 6: Adjust Tension
P
Note1:
Be sure to keep the arm in horizontal position during adjustment.
Falls down
Turn counter-clockwise(“+”direction) to increase gas
spring tension until the monitor canstay at the desired
height by itself.
Turn clockwise(“-”direction) to reduce gas spring tension
until the monitor canstay at the desired height by itself.
Rises up
CAUTION
Monitor Weight 2kg 3kg 4kg 5kg 6kg 7kg 8kg
Circles (AT LEAST)
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension in upper arm (A) using 6 mm allen key (P).
1 4 8 11 14 17
min
As for how many circles the screw should be turned, refer to below diagram.
Note2:
If the monitor falls down and fails to stay at the desired
height by itself:
If the monitor rises up and fails to stay at the desired
height by itself:
STEP 5: (Continued)
08
STEP 7: Cable Management
Run cables from monitor through bottom of gas spring arm. Reattach plastic covers as shown in diagram.
Remove bottom plastic covers from gas spring arm as shown in diagram.
Adjust as Desired
09
DESK DESK
Pay attention while clamp install !
360°
360°
360°
+90°
-45°
180°
Adjust monitor position and rotation.
Tabla de contenidos
Otros manuales de Rack y soporte de Mountup
Mountup
Mountup MU0022 Manual de usuario
Mountup
Mountup MU1005 Manual de usuario
Mountup
Mountup MU0002 Manual de usuario
Mountup
Mountup MU4001 Manual de usuario
Mountup
Mountup MU4003 Manual de usuario
Mountup
Mountup MU0045 Manual de usuario
Mountup
Mountup MU9101B Manual de usuario
Mountup
Mountup MU2001 Manual de usuario
Mountup
Mountup MU0026 Manual de usuario
Mountup
Mountup MU0014 Manual de usuario
Mountup
Mountup MU0029 Manual de usuario
Mountup
Mountup MU0029 Manual de usuario
Mountup
Mountup MU7012 Manual de usuario
Mountup
Mountup MU2002 Manual de usuario
Mountup
Mountup MU0060 Manual de usuario
Mountup
Mountup MU0011 Manual de usuario
Mountup
Mountup MU0005 Manual de usuario
Mountup
Mountup MU0023 Manual de usuario
Mountup
Mountup MU0004 Manual de usuario
Mountup
Mountup MU5004 Manual de usuario
