Mountup MU0033 Manual de usuario
Premium Dual Monitor Stand
Instruction Manual
If you have any questions , please contact us.
MU0033
V2.0
75x75
100x100 35"
(3~14kg)x2
(6.6~30.9lbs)x2
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, please contact us.
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
01
PACKAGE CONTENTS
(30.9lbs)x2
(14kg)x2
A (x2)
Upper Arm
B (x2)
Lower Arm
C (x1)
Base
D (x1)
Bracket
E (x1)
Base Support Cover
F (x2)
VESA Plate
O (x1)
3mm Allen Key
H (x1)
Carriage Bolt
N (x2)
Bolt
I (x1)
Grommet Base
J (x1)
Support Plate
K (x1)
Wingnut
L(x5)
M6x10
M (x4)
Pad
P (x1)
4mm Allen Key
Q (x1)
6mm Allen Key
M-E (x8)
D6 Washer Spacer
M-C (x8)
M6x12
M-F (x8)
M-B (x8)
M4x16
M-D (x8)
M6x16
M-A (x8)
M4x12
G (x1)
Clamp
02
Q
C
Q
C1
Mount Bracket (D) to Base (C) with Bolts (L). Bolts could be tightened by the 4mm Allen Key (P).
Apply pads (M) to the Bolts (L) to avoid desk scratches.
Similarly, attach Clamp (G) to Bracket (D) with Bolts (L) and 4mm Allen Key (P).
ASSEMBLY STEPS
STEP 1: Clamp Installation OR Grommet Base Installation
OPTION A: Clamp Installation
Adjust the Clamp width to t with desk. Secure stand to desktop by tightening Clamp (G) or by Allen key (Q).
Attach Base Support Cover (E) to Bracket (D).
C
D
P
LM
L
P
10-55mm
G
D
G
L
50-85mm
OR
P
E
D
Q
OR
03
D
G
04
OPTION B: Grommet Base Installation
Place Carriage Bolt (H) through the center of Grommet Base (I).
Mount Grommet Base to Base (C) bottom with Bolts (L) and tighten by 4mm allen key (P).
Apply pads (M) to the Bolts (L) to avoid desk scratches.
STEP 1: (Continued)
Run Carriage Bolt (H) through Grommet Hole on desktop. Attach Support Plate (J) and Wingnut (K).
Last step, tighten Wingnut (K).
P
H
I
L
C
M
J
K
H
STEP 2: Arm Installation
Install the lower arm (B) and the upper arm (A) to the base (C). Secure the arm by tightening the inside screw
using 3mm Allen key (O).
B
O
O
C
A
05
DO NOT tighten the
screw excessively or
it might be stripped.
DO NOT tighten the
screw excessively or
it might be stripped.
Note: Please note that the side with
the label“ ” is installed on the
base(C) when installing the lower
arm(B) to the base (C).
NOTE: Hand tighten screws toavoid over tightening.
STEP 3 : Attach Monitor
M-A
M-C
M-E
Q
M-B
M-D
M-E
M-F
Q
OPTION B: Curved Back Monitor
Attach the VESA plate (F) to back of monitor and secure
with screws (M-B) or (M-D) with washers (M-E)and
washers(M-F)using 6 mm Allen Key (Q). Do not tighten
the screws excessively or your monitor might be damaged.
OPTION A: Flat Back Monitor
Attach the VESA plate (F) to back of monitor and
secure with screws(M-A)or(M-C) with washers(M-E)
using 6 mm Allen Key (Q). Do not tighten the screws
excessively or your monitor might be damaged.
F
F
06
07
Slide the monitor onto the head of swivel arm, install the security bolt (N). Make sure the security
bolt is installed before you rotate the monitor.
STEP 4: Hang Monitor
Refer to below illustrations to adjust tilting angle of your monitor.
Tilts down
Note:
1. Loosen the tilting bolt.
2. Adjust monitor to your
desired tilting angle.
3. Retighten the tilting bolt to
Important Notice:
The gas spring tension is pre-set to the weakest level by default, please hold your monitor
by both hands and do not let go so soon after the VESA plate is attached to the swivel arm.
It's suggested to loose hold of the monitor in a slow & gentle way while observing if the gas
spring arm falls down greatly.
N
Q
STEP 5: Adjust Tension
Note1:
Be sure to keep the arm in horizontal position during adjustment.
Falls down
After being attached to the arm, the monitor fallsdown
and can not stay at the desired height by itself.
Turn counter-clockwise(“+”direction) to increase gas
spring tension until the monitor canstay at the desired
height by itself.
After being attached to the arm, the monitor rises up and
can notstay at the desired heightby itself.
Turn clockwise(“-”direction) to reduce gas spring tension
until the monitor canstay at the desired height by itself.
Rises up
CAUTION
As for how many circles the screw should be turned, the table below is for reference.
Note2:
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension in upper arm (A) using 6 mm allen key (Q).
A
Q
08
Monitor Weight 3kg 4kg 7kg 10kg 13kg 14kg
Circles (AT LEAST) 5 7 10 13 16 20
09
STEP 6: Cable Management
Run cables from monitor through bottom of arm. Reattach plastic covers as shown in diagram.
Remove bottom plastic covers from arm as shown in diagram. from the arm, do not need to take much eort
to pull the ends of the cable cover away from the arm.
1
1
2
1
1
2
Tabla de contenidos
Otros manuales de Rack y soporte de Mountup
Mountup
Mountup MU0004 Manual de usuario
Mountup
Mountup MU0001 Manual de usuario
Mountup
Mountup MU4001 Manual de usuario
Mountup
Mountup MU0004 Manual de usuario
Mountup
Mountup MU2002 Manual de usuario
Mountup
Mountup MU0023 Manual de usuario
Mountup
Mountup MU0022 Manual de usuario
Mountup
Mountup MUA6008B Manual de usuario
Mountup
Mountup MU0045 Manual de usuario
Mountup
Mountup MU0026 Manual de usuario
Mountup
Mountup PR8001 Manual de usuario
Mountup
Mountup MU2001 Manual de usuario
Mountup
Mountup MU9101B Manual de usuario
Mountup
Mountup MU6002 Manual de usuario
Mountup
Mountup MU0027 Manual de usuario
Mountup
Mountup MU0005 Manual de usuario
Mountup
Mountup MUA6007B Manual de usuario
Mountup
Mountup MU0032 Manual de usuario
Mountup
Mountup MU2001 Manual de usuario
Mountup
Mountup MU5001 Manual de usuario
