Mountup MU2001 Manual de usuario

Polished Aluminium Single Monitor Wall Mount

Instruction Manual

If you have any questions , please contact us.

75x75

100x100

1.5~8kg

3.3~17.6lbs

32"

MU2001

V2.0

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of

this product, please contact us.

Beforestarting assembly, verify all parts are included and undamaged. Improperinstallation may cause damage or

weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.

ADULT SUPERVISION IS REQUIRED.

WARNING!

PACKAGE CONTENTS

B (x1)

VESA Plate

A (x1)

Arm Assembly

NOTE: Not all hardware included will be used.

M-E (x4)

D6 Washer

M-C (x4)

M6x12

M-B (x4)

M4x16

M-D (x4)

M6x16

M-A (x4)

M4x12 M-F (x4)

Spacer

W-B (x3)

Anchor

W-C (x3)

Washer

W-A (x3)

Lag Bolt

( )

Installation Tools

Awl

D (x3)

Decorative Cover

E(x1)

6mm Allen Key

C (x1)

Bolt

ASSEMBLY STEPS

STEP 1: Attach Arm Assembly to Wall

OPTION A: Wood Stud Installation

ø 4.5mm

(ø 3/16")

55mm

(2.2")

W-C W-A

Caution:

Do not use anchor in drywall

or wood！

Locate your studs. Verify and mark

Position the Arm Assembly (A) at your

desired height and line up the holes

withyour stud center line. Level the

Arm Assembly (A) and mark the pilot

hole locations.

Drill pilot holes using a ø3/16 in.

(ø4.5 mm) diameter drill bit.

Install Arm Assembly (A) using lag

bolts (W-A) and washers (W-C).

Tighten the lag bolts until they are

Assembly (A).

STEP 1: (Continued)

60mm

(2.4")

ø10mm

(ø 3/8")

W-C W-A

W-B

OPTION B: Solid Concrete Wall Installation

60mm (2.4 )

Position the Arm Assembly (A) at

yourdesired height , level the Arm

Assembly (A) and mark the pilot hole

locations.

Drill pilot holes using a ø3/8 in.

(ø10 mm) diameter drill bit.

Install Arm Assembly (A) using lag

bolts (W-A), anchors (W-B)and

washers (W-C). Tighten the lag bolts

the Arm Assembly (A).

STEP 2: Attach Decorative Cover

Attach Decorative Covers (D) to Lag Bolts (W-A).

W-A

NOTE: Hand tighten screws to avoid over tightening.

STEP 3 : Attach Monitor

M-A

M-C

M-E

M-B

M-D

M-E

M-F

OPTION B: Curved Back Monitor

Attach the VESA plate (B) to back of monitor and secure

with screws (M-B) or (M-D) with washers (M-E)and

OPTION A: Flat Back Monitor

Attach the VESA plate (B) to back of monitor and

secure with screws(M-A)or(M-C) with washers(M-E)

washers(M-F)using 6 mm Allen Key (E). Do not tighten the

screws excessively or your monitor might be damaged.

using 6 mm Allen Key (E). Do not tighten the screws

excessively or your monitor might be damaged.

Slide the monitor onto the head of swivel arm, install the security bolt (C). Make sure the security

bolt is installed before you rotate the monitor.

STEP 4: Hang Monitor

Refer to below illustrations to adjust tilting angle of your monitor.

Tilts down

Note:

1. Loosen the tilting bolt.

2. Adjust monitor to your

desired tilting angle.

3. Retighten the tilting bolt to

Important Notice:

The gas spring tension is pre-set to the weakest level by default, please hold your monitor

by both hands and do not let go so soon after the VESA plate is attached to the swivel arm.

It's suggested to loose hold of the monitor in a slow & gentle way while observing if the gas

spring arm falls down greatly.

STEP 5: Adjust Tension

Note1:

Be sure to keep the arm in horizontal position during adjustment.

Falls down

After being attached to the arm, the monitor falls down

and can not stay at the desired height by itself.

Turn counter-clockwise(“+”direction) to increase gas

spring tension until the monitor can stay at the desired

height by itself.

After being attached to the arm, the monitor rises up and

can not stay at the desired height by itself.

Turn clockwise(“-”direction) to reduce gas spring tension

until the monitor can stay at the desired height by itself.

Rises up

CAUTION

As for how many circles the screw should be turned, the table below is for reference.

Note2:

tension in upper arm using 6 mm allen key (E).

Monitor Weight 1.5kg 3kg 4kg 5kg 6kg 7kg 8kg

Circles (AT LEAST) 108643min 12

STEP 5: (Continued)

STEP 6: Cable Management

On the bottom portion of the spring arm, insert the cable and slide the cable cover down;

On the upperportion of the spring arm, insert the cable and press the tabs on the inside of the cable cover

slightly inward and slide down to reattach the cable cover.

For both bottom and upper portion of the spring arm, just slide the cable cover up and away from the spring

Adjust as Desired

Note: When tilted, if the monitor sags or does not stay,

please fasten the tilting bolt on the mount until the

monitor canbe held at any angle as needed.

+90°

-45°

max280mm

180°

360°

180°

Adjust monitor position and rotation.

Otros manuales para MU2001

Tabla de contenidos

Otros manuales de Rack y soporte de Mountup

Mountup

Mountup MU0024 Manual de usuario

Mountup

Mountup MU2002 Manual de usuario

Mountup

Mountup MU0022 Manual de usuario

Mountup

Mountup MU1005 Manual de usuario

Mountup

Mountup MU0014 Manual de usuario

Mountup

Mountup MU0005 Manual de usuario

Mountup

Mountup MU6003 Manual de usuario

Mountup

Mountup MU2005 Manual de usuario

Mountup

Mountup MU0027 Manual de usuario

Mountup

Mountup MU0021 Manual de usuario

Mountup

Mountup MUA6007B Manual de usuario

Mountup

Mountup MU0014 Manual de usuario

Mountup

Mountup MU0006 Manual de usuario

Mountup

Mountup MU0023 Manual de usuario

Mountup

Mountup MU0006 Manual de usuario

Mountup

Mountup MU0033 Manual de usuario

Mountup

Mountup MU0011 Manual de usuario

Mountup

Mountup MU0029 Manual de usuario

Mountup

Mountup MU6002 Manual de usuario

Mountup

Mountup MU4003 Manual de usuario

Mountup

Mountup MU6001 Manual de usuario

Mountup

Mountup MU4001 Manual de usuario

Mountup

Mountup MUA6008B Manual de usuario

Mountup

Mountup MU0001 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario