molex 63816-0800 Manual de usuario
Power Crimp Head for Crimp Dies and Locator Kits
Doc No: ATS-63816 8 Release Date: 5-26-11 UNCONTROLLED COPY Page 1 of 4
Revision: A Revision Date: 5-26-11
Type 4D
Power Crimp Head
Application Tooling
Speci ication Sheet
Order No. 63816-0800
Features
The Quick Change Power Crimp Head is easily installed onto the Battery Power Crimp Tool
(Order No. 63816- 2 )
Powered crimp tools help reduce fatigue and discomfort from repetitive manual crimping and allows portability
A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position
SCOPE
The 63816- 8 Power Crimp Head was created for use with Type 4D Crimp Dies and Locator when used with the
Battery Powered Tool (Order No. 63816- 2 ).
Installation
To install the Power Crimp Head onto the Battery Powered Tool,
(Order No. 63816- 2 ), refer to the Instruction Manual TM-
63816 2 , Section 3, “Set-Up and Adjustments”.
Locator Installation and Removal
To remove the locator
1. Open the Power Crimp Head to remove the locator.
2. Squeeze gently on the lower area of the locator assembly, shown
in Figure 1, with your thumb and index finger. The lower tabs of
the locator should disengage from the Power Crimp Head.
3. Lift and pull away from the Power Crimp Head. The top locator
hooks should slip out of the top slots easily. See Figure 1.
To install the locator
1. Install the locator assembly.
2. Press the red insert down as far as it will go. See Figure 2.
3. The locator goes on the opposite side from the dies with the wire
gauge markings.
4. While holding onto the lower part of the locator with your thumb
and index finger, insert the locator top hooks (2) into the Power
Crimp Head top slots.
5. Rotate the locator down and press the lower tabs into the two
bottom slots of the head. To secure the locator into place, the
lower tabs must snap into place on the head frame.
TOP SLOT
OF THE
HANDTOOL
SQUEEZE
HERE
SQUEEZE
HERE
LOCATOR
Figure 1
TOP HOOKS
TOP SLOT
OF THE
HANDTOOL
LOWER TABS
Power Crimp Head for Crimp Dies and Locator Kits
Doc No: ATS-63816 8 Release Date: 5-26-11 UNCONTROLLED COPY Page 2 of 4
Revision: A Revision Date: 5-26-11
Figure 4
MATCH UP
MARKINGS
WIRE GAUGE
IDENTIFICATIONS
SHOWING
FRONT
BACK
FIGURE 3
M3 BHCS
X 8 LONG
E1
E2
I2
I1
POWER CRIMP HEAD
M3 BHCS
X 14 LONG
Removing the Crimp Dies rom the Power Crimp Head
1. Open the Power crimp Head.
2. Remove the two M3 BHCS.
3. Remove the crimp dies as shown in Figure 3.
4. Make sure all of components removed from the Power Crimp Head are reinstalled into
the Power Crimp Head in the same manner.
Installing the Crimp Dies in the Power Crimp Head
1. Select the desired crimping dies.
2. Insert the Anvils or dies (E1 and I1) into the bottom slots of the nest. Install the M3 x
14 long BHCS and lightly tighten in place.
Note: The tool part number markings on the dies go inward so they will not be visible when installed.
3. Insert the Punches or dies (E2 and I2) into the top slots of the nest. Install the M3 x 8 long BHCS and lightly
tighten in place. See Figure 3.
4. Make sure the small markings on the individual dies match up and wire gauge identification (AWG) marks
should be facing out and aligned as shown in Figure 4.
Note: Make sure the longer screw only goes into the lower dies.
5. Completely close the crimp dies until they are touching, and then securely tighten the M3 BHCS.
Adjustments
The crimp height on the 63816- 8 Power Crimp Head can be adjusted, if necessary. To do this, first measure the
conductor crimp height of a crimped terminal and compare to the crimp specification listed in the product
specification for that terminal. If an adjustment is required, follow the procedure, below:
MAKE SURE
CENTER OF LOCATOR
IS IN THE
DOWN POSITION
Figure 2
Power Crimp Head for Crimp Dies and Locator Kits
Doc No: ATS-63816 8 Release Date: 5-26-11 UNCONTROLLED COPY Page 3 of 4
Revision: A Revision Date: 5-26-11
1. Loosen the locking set screw located just below the knurled knob at the top of the Power Crimp Head. See
Figure 5.
2. If the crimp height is too loose, rotate the knob, a small amount, in the counter-clockwise direction. Crimp
another terminal and re-check the crimp height.
3. If the crimp height is too tight, turn the knob clockwise and follow
the same procedure.
4. Do this until the proper crimp height is achieved.
5. When the proper crimp height is achieved, lock the set screw.
Operation
1. To load a terminal and position the wire in the terminal in the
Power Crimp Head, follow the loading procedure as explained in
the Hand Crimp Tool Specification sheet.
2. Crimp the terminal by squeezing the trigger on the side of the
battery actuator until the tool cycles and returns and the jaws
open.
3. Remove the terminal from the locator and inspect the crimp for
proper quality.
CAUTION: Never place fingers into the tooling nest area.
Maintenance
It is recommended that each operator of the tool be made aware of, and
responsible for, the following maintenance steps:
1. This tool was engineered for durability, but like any fine piece of
equipment, it needs cleaning and lubrication for a maximum service
life of trouble-free crimping
2. Remove dust, moisture and other contaminants with a clean brush,
or soft, lint-free cloth.
3. Do not use any abrasive materials that could damage the tool.
4. The use of a light oil, such as SAE 3 weight automotive oil, every
5, crimps, or monthly, will significantly enhance the tool life and
ensure a stable calibration. Make certain all sliding surfaces in the
tool head are protected with a thin coat of high quality machine oil.
See Figure 1 for lubrication points. Do not oil excessively and wipe
excess oil from the tool frame when complete.
5. Store the tool in a clean and dry area when not in use.
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life-tested. All tools are warranted free of manufacturing defects for a period of 30 days.
Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not be
applicable to altered, misused, or damaged tools.
LOCKING
SET SCREW
Figure 5
KNURLED
KNOB
LUBRICATION
POINTS
(BOTH SIDES)
LIGHT OIL
(EVERY MONTH
OR
5,000 CRIMPS)
Figure 6
Power Crimp Head for Crimp Dies and Locator Kits
Doc No: ATS-63816 8 Release Date: 5-26-11 UNCONTROLLED COPY Page 4 of 4
Revision: A Revision Date: 5-26-11
Parts List
Item
Order No
Description
Quantity
1
63816
-
8
Power
Crimp
Head
(for style 4D crimp tools)
1
2
638
16
-
8 1
Return Spring
2
http://www.molex.com
2
2
Figure 7
1
Tabla de contenidos
Otros manuales de Herramientas de crimpado de molex
molex
molex CR60927A Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63811-8900 Manual de usuario
molex
molex 63823-0400 Guía del usuario
molex
molex 63827-2970 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63823-5100 Guía del usuario
molex
molex 63827-1600 Manual de usuario
molex
molex 63811-6670 Manual de usuario
molex
molex 11-01-0185 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63811-7400 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63827-3200 Manual de usuario
molex
molex AT AFIFG Manual de usuario
molex
molex 63811-6170 Manual de usuario
molex
molex 63825-5000 Manual de usuario
molex
molex 63825-5770 Manual de usuario
Manuales populares de Herramientas de crimpado de otras marcas
Textron
Textron ESG105L Manual de usuario
Tyco Electronics
Tyco Electronics 90035-3 Manual de usuario
Emerson
Emerson Klauke ES 20RMCCFB Manual de usuario
Continental Refrigerator
Continental Refrigerator PC150HD Manual de usuario
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario