Molex 207129 Series Manual de usuario

Hand Crimp Tool for OBD II 1.52mm (.060”) Crimp Terminals

Doc No ATS-6381947HM Release Date 02-09-09 UNCONTROLLED COPY Page 1 of 6

Revision B Revision Date 08-11-10

INSULATION

CRIMP

▲

SEE NOTE

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

Application Tooling

Speci ication Sheet

Modular Crimp Head

Order No. 63819-4770

Hand Crimp Tool

Order No. 63819-4700

FEATURES

% A full cycle ratcheting hand tool ensures complete crimps

% Ergonomically designed soft handles

% Precisely designed crimping profiles with simple contact positioning

% Easy handling due to outstanding force ratio

% Modular Crimp Head is removable and can be use in the Air Powered Tool Order No.63816-0100,

accompanied by Air Powered Crimp Adapter (Order No. 63816-0700).

% Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V),

accompanied by Battery Powered Crimp Adapter (Order No. 63816-0600).

SCOPE

Products OBD II 1.52mm (.060”) Crimp Terminal, 0.30-0.50mm² and 20-22 AWG.

Terminal

Series No.

Terminal Order No.

Reel Form Only

Wire Size Insulation Diameter Strip Length

IPC/WHMA-A620 Terminal

AWG mm²

mm In. mm In. mm In.

57964 57964-9702

AVS-0.3,

CAVS-0.3

0.37

1.40-2.30

.055-.090

1.40-2.30

.055-.090

3.60-4.80

.142-.189

22AWG 0.35

AVS-0.5,

CAVS-0.5

0.56

20AWG 0.50

To achieve optimum IPC-A620 insulation crimps, use this insulation OD range.

Overall insulation OD specification for terminal.

Customer to cut off terminal from reel 0.25mm (.010”) maximum Cut-off Tab.

DEFINITION OF TERMS

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the

scope.

TYPE 4A

Hand Crimp Tool for OBD II 1.52mm (.060”) Crimp Terminals

Doc No ATS-6381947HM Release Date 02-09-09 UNCONTROLLED COPY Page 2 of 6

Revision B Revision Date 08-11-10

TERMINAL

PRE-STRIPPED

WIRE

LOCATOR

Figure 1

WIRE STOP

BLADE

▲Insulation Crimp Note

Due to the terminal’s insulation grip design and/or

insulation diameter range, this tool uses “overlap”

form geometry in the insulation punch. This produces

an overlap insulation crimp (A620 – compliant). While

the insulation punch profile may appear “lopsided”,

this is a normal condition for this tool. See figure to

the right. (Some tools with multiple crimp pockets

may not have the “overlap” profile on all pockets).

CRIMP SPECIFICATION

Terminal Series No. Bell mouth Cut-o Tab Maximum Conductor Brush

mm In. mm In. mm In.

57964 0.20-0.80 .008-.031 0.20 .008 0.30-1.50 .012-.059

After crimping, the crimp profiles should measure the following (See notes on page 4).

Terminal

Series No

Wire Size Conductor Crimp Insulation Crimp Pull Force

Minimum Pro ile

Height (Re .) Width (Re .)

Height (Re .)

Width (Re .)

AWG mm2

mm In. Mm In. mm In. mm In. N Lb. AWG 22

0.3mm2

AWG 20

0.5mm2

57964

0.3, 0.3f 0.37 1.05-1.15

.041-.045

1.90 .075 2.20 .087 2.25 .089 58.8

13.2

22 AWG

0.35 1.05-1.15

.041-.045

1.90 .075 2.20 .087 2.25 .089 58.8

13.2

0.5, 0.5f 0.56 1.15-1.25

.045-.049

1.90 .075 2.40 .095 2.35 .093 88.2

19.8

20 AWG

0.50 1.15-1.25

.045-.049

1.90 .075 2.40 .095 2.35 .093 88.2

19.8

ΤΤ

Τ Tool Quali ication Notes

1. Pull Force should be measured with no influence from the

insulation crimp.

1. The above specifications are guidelines to an optimum crimp.

OPERATION

Open the tool by squeezing the handles together, at the end of the

closing stroke, the ratchet mechanism will release the handles, and

the hand tool will spring open.

Crimping Terminals

1. Lift the wire stop blade up.

2. Insert the terminal fully into the correct profile until the terminal is fully seated and stops.

3. Bring down the wire stop blade.

4. Slide the pre-stripped wire into the wire stop blade. See Figure 1. Be sure to hold the wire in place until the

terminal is fully crimped. See Figure 2.

5. Close the tool until the ratchet releases, the tool handles will then spring open.

6. Lift the wire stop blade up if it is still in down position.

7. Carefully remove the crimped terminal.

OVERLAP

INSULATION

CRIMP

OVERLAP FORM GEOMETRY

ANVIL

PUNCH

WIRE

Hand Crimp Tool for OBD II 1.52mm (.060”) Crimp Terminals

Doc No ATS-6381947HM Release Date 02-09-09 UNCONTROLLED COPY Page 3 of 6

Revision B Revision Date 08-11-10

Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be followed.

Maintenance

It is recommended that each operator of the tool be

made aware of, and responsible for, the following

maintenance steps

1. Remove dust, moisture, and other

contaminants with a clean brush, or soft, lint

free cloth.

2. Do not use any abrasive materials that could

damage the tool.

3. Make certain all pins; pivot points and bearing

surfaces are protected with a thin coat of high

quality machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment

it needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30

weight automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool

life.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by lifting the ratchet release lever. See Figure 6.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Repetitive use of this tool should be avoided.

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Figure 2

CONDUCTOR

PUNCH

WIRE

LOCATOR

TERMINAL

INSULATION

PUNCH

INSULATION

ANVIL

CONDUCTOR

ANVIL

WIRE STOP

BLADE

Hand Crimp Tool for OBD II 1.52mm (.060”) Crimp Terminals

Doc No ATS-6381947HM Release Date 02-09-09 UNCONTROLLED COPY Page 4 of 6

Revision B Revision Date 08-11-10

Notes:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above).

Variations in tools, terminals, wire stranding, and insulation types may affect crimp height.

3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all

insulation sizes.

4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts

available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no

influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips

on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping

Handbook 63800-0029 for additional information on crimping and crimp testing.

6. Molex does not certify crimp hand tools.

CAUTION Molex crimp specifications are valid only when used with Molex terminals and tooling.

Hand Crimp Tool for OBD II 1.52mm (.060”) Crimp Terminals

Doc No ATS-6381947HM Release Date 02-09-09 UNCONTROLLED COPY Page 5 of 6

Revision B Revision Date 08-11-10

MODULAR

CRIMP

HEAD

BATTERY

POWER

CRIMP

ADAPTER

LOCKING

PINS

LOCKING PINS

BATTERY

POWERED

TOOL

AIR

POWER

TOOL

MODULAR

CRIMP HEAD

LOCKING

PINS

LOCKING

PINS

AIR

POWER

CRIMP

ADAPTER

Applications or the Modular Crimp Head

WARNING NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction

and without first reading and understanding the instructions in the proper Manual or Specification Sheet.

See Chart below for the correct Manual or Specification Sheet.

WARNING NEVER install tooling or service this tool while it is into any power source. Disconnect the

power by unplugging or turn off the Actuator from its power source.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

The chart below shows all applications for this Modular Crimp Head.

Modular Crimp Head

Order No.

Tool

Order no.

Tool

Description

Adapter

Order No.

Adapter

Description

Figure

No.

63819-4770

63816-0000

Hand Crimp Frame (Short) N/A N/A 3

63816-0050

Hand Crimp Frame (Long) N/A N/A 3

63816-0200

Battery Power Tool (110 V)

63816-0600

Battery Power Crimp Adapter

63816-0250

Battery Power Tool (220 V)

63816-0600

Battery Power Crimp Adapter

63816-0100

Air Power Tool 63816-0700

Air Power Crimp Adapter 5

Applications or the Modular Crimp Head

Hand Crimp Tool Battery Powered Tool Air Powered Tool

Figure 3 Figure 4 Figure 5

MODULAR

CRIMP

HEAD

LOCKING

PINS

HAND CRIMP

FRAME LONG

OR SHORT

Hand Crimp Tool for OBD II 1.52mm (.060”) Crimp Terminals

Doc No ATS-6381947HM Release Date 02-09-09 UNCONTROLLED COPY Page 6 of 6

Revision B Revision Date 08-11-10

RATCHET

RELEASE LEVER

HANDLE

SPRING

CRIMPING

SPRING (2)

Figure 6

M4 x 14

LONG BHCS

PARTS LIST

Hand Crimp Tool 63819-4700

Item

Order Number

Description Quantity

1 63819-4770 Modular Crimp Head 1 (Ref)

2 63816-0050 Hand Crimp Frame (Long)

1 (Ref)

3 63819-4775 Locator 1

4 63816-0001 Locking Pin 2

5 63600-0525 Handle Spring 1

6 63600-0520 Crimping Spring 2

http //www.molex.com

Otros manuales para 207129 Series

100

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 43178 Series Manual de usuario

molex

molex HCS-125 Series Manual de usuario

molex

molex 63827-3200 Manual de usuario

molex

molex 63825-5800 Guía del usuario

molex

molex 63819-4100 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63811-7000 Manual de usuario

molex

molex 11-01-0101 Manual de usuario

molex

molex 207128 Series Manual de usuario

molex

molex 63825-6900 Guía del usuario

molex

molex 63825-9400 Guía del usuario

molex

molex 207129 Series Manual de usuario

molex

molex CR5974 Manual de usuario

molex

molex 63825-5770 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63828-0600 Manual de usuario

molex

molex 98897 Manual de usuario

molex

molex 5050731100 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 11-01-0185 Manual de usuario

molex

molex 63811-5600 Manual de usuario

molex

molex 63811-9200 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex CR1031E Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario