Metra Electronics 99-8201 Manual de usuario
KIT COMPONENTS
TOOLS REQUIRED
Cutting tool
Socket wrench
Phillips screwdriver
KIT FEATURES
ISO-DIN
head unit
provisions
Pocket
provisions
99-8201
INSTALLATION
INSTRUCTIONS
APPLICATIONS
CAR PAGE
TOYOTA
Celica 2000-05................................................1-3
Echo 2000-05..................................................1-3
Radio
Housing
"C"
Radio
Housing
"E"
Mounting
Brackets
Re-connect the battery terminal and test the unit
for proper operation. Mount the head unit/kit
assembly to the sub-dash with (4) screws
previously removed in step #1.
76
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
(6) #6 x ¼"
Phillips Flat-
5
Align the holes in the Mounting Brackets with the holes in the ISO-DIN head unit and mount
the Brackets to the head unit with the screws included with the unit.
3
Pocket
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-07 METRA ELECTRONICS CORPORATION
rev. 06-15-07
2
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip and
remove the gear shifter trim bezel and remove (2)
Phillips screws exposed below the climate
controls. Pull off climate control knobs and
remove (2) Phillips screws exposed. Unclip the
climate control/factory radio trim bezel and
remove. Remove (4) 10mm screws securing the
factory head unit and disconnect the wiring.
Locate Radio Housing "C". Using the
dotted lines as a guide, cut and remove
all tabs on the Mounting Brackets
EXCEPT tabs "C". Skip to the
Installation Instructions for ALL
VEHICLES on Page #2.
Locate Radio Housing "E". Using the
dotted lines as a guide, cut and remove
all tabs on the Mounting Brackets
EXCEPT tabs "E". Skip to the
Installation Instructions for ALL
VEHICLES on Page #2.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove the
climate control knobs and (2) Phillips screws
exposed. Unclip and remove the climate control
trim bezel. Depress the side clips securing the
climate control panel and move the panel to
access (2) Phillips screws from the top of the
factory radio brackets. Remove the ashtray.
Unclip and remove the radio trim bezel. Remove
(2) Phillips screws from the bottom of the radio
brackets and disconnect the wiring.
1
1
TOYOTA Celica 2000-05 ALL VEHICLES
TOYOTA Echo 2000-05
3
4
Snap the Pocket onto the back of the Radio Housing.
Attach the Mounting Brackets to the sides of the Radio Housing by inserting the slotted
Bracket tabs into the slotted Housing tabs. (Be sure the mounting bosses on the Brackets
align with the mounting bosses on the Pocket ). Mount the Brackets to the Pocket with (6) #6 x
¼" Phillips Flat-Head Screws.
2
2
"C"
"E"
"E"
"C"
CUT
CUT
CUT
CUT
CUT
2
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip and
remove the gear shifter trim bezel and remove (2)
Phillips screws exposed below the climate
controls. Pull off climate control knobs and
remove (2) Phillips screws exposed. Unclip the
climate control/factory radio trim bezel and
remove. Remove (4) 10mm screws securing the
factory head unit and disconnect the wiring.
Locate Radio Housing "C". Using the
dotted lines as a guide, cut and remove
all tabs on the Mounting Brackets
EXCEPT tabs "C". Skip to the
Installation Instructions for ALL
VEHICLES on Page #2.
Locate Radio Housing "E". Using the
dotted lines as a guide, cut and remove
all tabs on the Mounting Brackets
EXCEPT tabs "E". Skip to the
Installation Instructions for ALL
VEHICLES on Page #2.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove the
climate control knobs and (2) Phillips screws
exposed. Unclip and remove the climate control
trim bezel. Depress the side clips securing the
climate control panel and move the panel to
access (2) Phillips screws from the top of the
factory radio brackets. Remove the ashtray.
Unclip and remove the radio trim bezel. Remove
(2) Phillips screws from the bottom of the radio
brackets and disconnect the wiring.
1
1
TOYOTA Celica 2000-05 ALL VEHICLES
TOYOTA Echo 2000-05
3
4
Snap the Pocket onto the back of the Radio Housing.
Attach the Mounting Brackets to the sides of the Radio Housing by inserting the slotted
Bracket tabs into the slotted Housing tabs. (Be sure the mounting bosses on the Brackets
align with the mounting bosses on the Pocket ). Mount the Brackets to the Pocket with (6) #6 x
¼" Phillips Flat-Head Screws.
2
2
"C"
"E"
"E"
"C"
CUT
CUT
CUT
CUT
CUT
KIT COMPONENTS
TOOLS REQUIRED
Cutting tool
Socket wrench
Phillips screwdriver
KIT FEATURES
ISO-DIN
head unit
provisions
Pocket
provisions
99-8201
INSTALLATION
INSTRUCTIONS
APPLICATIONS
CAR PAGE
TOYOTA
Celica 2000-05................................................1-3
Echo 2000-05..................................................1-3
Radio
Housing
"C"
Radio
Housing
"E"
Mounting
Brackets
Re-connect the battery terminal and test the unit
for proper operation. Mount the head unit/kit
assembly to the sub-dash with (4) screws
previously removed in step #1.
76
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
(6) #6 x ¼"
Phillips Flat-
5
Align the holes in the Mounting Brackets with the holes in the ISO-DIN head unit and mount
the Brackets to the head unit with the screws included with the unit.
3
Pocket
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-07 METRA ELECTRONICS CORPORATION
rev. 06-15-07
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Metra Electronics
Metra Electronics
Metra Electronics 99-9109B Manual de usuario
Metra Electronics
Metra Electronics 70-9800 Manual de usuario
Metra Electronics
Metra Electronics 99-7893 Manual de usuario
Metra Electronics
Metra Electronics 99-7389B Manual de usuario
Metra Electronics
Metra Electronics 95-3528 Manual de usuario
Metra Electronics
Metra Electronics 109-TO7 Manual de usuario
Metra Electronics
Metra Electronics 99-7006 Manual de usuario
Metra Electronics
Metra Electronics 99-6520B Manual de usuario
Metra Electronics
Metra Electronics 95-7393B Manual de usuario
Metra Electronics
Metra Electronics 99-7877S Manual de usuario
Metra Electronics
Metra Electronics 71-7552 Manual de instrucciones
Metra Electronics
Metra Electronics 99-8227S Manual de usuario
Metra Electronics
Metra Electronics 98-8999 Manual de usuario
Metra Electronics
Metra Electronics 95-8223 Manual de usuario
Metra Electronics
Metra Electronics 95-7953 Manual de usuario
Metra Electronics
Metra Electronics 99-7952 Manual de usuario
Metra Electronics
Metra Electronics 108-TO4 Manual de usuario
Metra Electronics
Metra Electronics 99-6507 Manual de usuario
Metra Electronics
Metra Electronics 99-7300 Manual de usuario
Metra Electronics
Metra Electronics 95-3105 Manual de usuario
