Metra Electronics 99-3307G Manual de usuario

REV. 1/26/2017 INST99-3307G

INSTALLATION INSTRUCTIONS FOR PART 99-3307G

CAUTION!

All accessories, switches, climate controls panels,

and especially air bag indicator lights must be connected before

cycling the ignition. Also, do not remove the factory radio with

the key in the on position, or while the vehicle is running.

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted gray to match factory finish

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (6) #8 x 3/8” Phillips screws

• E) (2) #10 x ¾” Phillips screws • F) (2) #10 panel clips • G) Axxess interface and wiring harness (not shown)

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Axxess interface and harness included

Antenna Adapter: • 40-EU55

• Panel removal tool • Phillips screwdriver

• 9/32” socket wrench

TOOLS REQUIRED

Chevy Equinox 2010-2015 / GMC Terrain 2010-2014

(with monochrome display)

99-3307G

Table of Contents

BCE FD

Dash Disassembly ................................................. 2

Kit Preparation....................................................... 3

Kit Assembly

–ISO DIN radio provision with pocket...................... 4

–ISO DDIN radio provision ...................................... 4

Axxess Interface Installation .............................5-7

99-3307G

Dash Disassembly

1. With pocket above factory radio

controls - Remove (2) 9/32”

screws from inside the pocket,

then unclip and remove the pocket.

2. Without pocket, just unsnap and

remove the panel. (Figure A)

3. Unsnap, unplug, and remove

the radio/ climate control panel.

(Figure B)

4. Unclip and remove the (2) side

panels from the left and right

side of the pocket/CD slot panel.

(Figure C)

5. Remove (4) 9/32” screws to remove

the pocket/CD slot panel. Remove

the power outlet and attach it to the

included pocket if installing single

DIN. If you are mounting a DDIN the

power outlet will not be retained with

this kit. Remove the rubber bottom

from the factory pocket and save it

for final assembly. (Figure D)

6. Remove (2) 9/32” screws from

each a/c vent then unclip and

remove the vents. Remove the

screws inside and under the vent

cavities and two from below the

vent locations. (this will allow flex

in the dash to fit the aftermarket in

later). (Figure E)

7. Remove (4) 9/32” screws securing

the radio chassis and remove.

(Figure F)

Continue to Kit Preparation

(Figure A) (Figure D)

(Figure C) (Figure F)

(Figure B) (Figure E)

99-3307G

(Figure A) (Figure B)

Kit Preparation

1. A small section of the sub-dash

must be cut with a cutting tool to

allow the radio to fit:

a. Remove the lip from the

section of dash just above

the original CD slot location

by cutting along the dotted line.

(Upper shading in figure A)

b. It is also recommended that

a portion of the sub dash

in front side of the console be

removed. (Lower shading in

figure A)

2. Attach the (2) #10 panel clips

included with the kit onto the front

legs of the radio brackets.

(Figure B)

Continue to Kit Assembly

99-3307G

Kit Assembly

ISO DDIN radio provision

1. Attach the radio brackets to the

radio using the screws supplied

with the radio. (Figure A)

Continue to Axxess

Interface Installation

(Figure B)

(Figure A)

ISO DIN radio provision with pocket

1. Attach the pocket to the radio

brackets using the (4) #8 x 3/8”

Phillips screws provided.

(Figure A)

2. Remove the metal DIN sleeve

and trim ring from the

aftermarket radio.

3. Slide the radio into the bracket/

pocket assembly and then secure

it using the screws supplied with

the radio. (Figure B)

Continue to Axxess

Interface Installation

(Figure A)

99-3307G

Axxess Interface Installation

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Can be used in amplified or non-amplified models

• Provides NAV outputs (mute, parking brake, reverse, and V.S.S)

• Pre-wired ASWC-1 harness included (ASWC-1 sold separately)

• Retains balance and fade

• Micro “B” USB updatable

INTERFACE FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape • Small flat-blade screwdriver

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

• Axxess Interface

• 3307 harness

INTERFACE COMPONENTS

From the 3307 harness to the aftermarket radio:

• Connect the Black wire with a ring terminal to the chassis of the aftermarket radio.

Attention: The interface will not function properly unless this step is performed

exactly as stated.

•Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Red wire to the accessory wire.

• If the vehicle is factory amplified, connect the Blue/White wire to the amp turn on

wire. This wire must be connected to hear sound from the factory amplifier.

• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.

• If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute

wire is not connected, the radio will turn off when OnStar is activated.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

Continued on the next page

Connections to be made

99-3307G

Connections to be made (cont.) Final Assembly

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire.

• The Black/Yellow wire is used for OnStar level adjustment for models that do not

come equipped with steering wheel controls. See the OnStar Level Adjustment

section for further instructions.

• Tape off and disregard the Green/Orange wire, it will not be used

in this application

• If retaining the factory AUX-IN jack, connect the Red & White RCA jacks to

the AUX input.

12-pin pre-wired ASWC-1 harness:

•This harness is to be used along with the optional ASWC-1 (not included) to

retain steering wheel audio controls. If the ASWC-1 is not being used, disregard

this harness. If it will be used, please refer to the ASWC-1 instructions for radio

connections and programming.

Note: Disregard the harness that comes with the ASWC-1.

• Connect the Red wire to the accessory wire.

Note: The relay attached to the 3307 harness is only for audible turn signal clicks.

No extra steps are required to retain this, so leave it as-is.

Continue to Final Assembly

With the key in the off position:

1. Connect the 3307 harness into the interface, and then to the vehicle.

2. Locate the factory antenna connector in the dash and complete all necessary

connections to the radio. Metra recommends using the proper mating adapter

from Metra.

3. Before using the kit it must be initialized.

Attention! If the interface loses power for any reason, the following steps will

need to be performed again. Also, if installing an ASWC-1 connect it after you

initialize and test the interface/radio, with the key in the off position.

a. Turn the key (or push-to-start button) to the ignition position and wait until

the radio comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the

off position, disconnect the interface, check all connections, reconnect the

interface, and then try again.

b. Turn the key to the off position, and then to the accessory position.

Test all functions of the installation for proper operation, before

reassembling the dash.

4. Test the radio and climate controls for proper operation.

Continued on the next page

99-3307G

Final Assembly (cont.)

5. Chime level adjustment:

a. With the vehicle on, turn it off and leave the keys in the ignition.

Open the driver’s door; chimes will be heard.

b. Wait 10 seconds, and then with a small flat-blade screwdriver, turn the

potentiometer clockwise to raise the chime level; counterclockwise to

lower the chime level.

c. When the chime is at a desired level, remove the keys from the ignition.

This will lock the chime volume at its current level.

6. OnStar level adjustment:

a. Press the OnStar button to activate it.

b. While OnStar is speaking, press the VOLUME UP or VOLUME DOWN buttons

on the steering wheel to raise or lower the OnStar level.

c. If the vehicle does not come equipped with steering wheel controls, find the

Black/Yellow wire on the 3307 harness.

d. While OnStar is speaking, tap the Black/Yellow wire to ground. Once the

OnStar level is set, it will stay at that level until the Black/Yellow wire is

tapped to ground again.

7. Attach the radio trim panel over the completed assembly, and then reassemble

the dash in reverse order of disassembly.

REV. 1/26/2017 INST99-3307G

INSTALLATION INSTRUCTIONS FOR PART 99-3307G

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians

IMPORTANT

If you are having difficulties with the installation

of this product, please call our Tech Support line

at 1-800-253-TECH. Before doing so, look over

the instructions a second time, and make sure

the installation was performed exactly as the

instructions are stated. Please have the vehicle

apart and ready to perform troubleshooting

steps before calling.

INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-3307G

REV. 1/26/2017 INST99-3307G

¡PRECAUCIÓN! Todos los accesorios, interruptores,

paneles de control climático y especialmente las luces

indicadoras de bolsa de aire deben estar conectados

antes de encender el encendido. Además, no extraiga la

radio de fábrica con la llave en la posición de encendido,

o mientras el vehículo esté funcionando.

Indice

• Herramienta para quitar paneles

• Destornillador Phillips • Llave del tubo 9/32”

HERRAMIENTAS REQUERIDAS

• Provisión de radio ISO DIN con cavidad

• Provisión de radio ISO DDIN

• Pintura color gris para igualar el acabado de fábrica

• A) Panel de la moldura del radio • B) Soportes del radio • C) Cavidad • D) (6) tornillos #8 de 3/8” Phillips

• E) (2) tornillos #10 de 3/4” Phillips • F) (2) ganchos #10 para panel • G) Interfaz y arnés de cableado Axxess (no mostrado)

CARACTERÍSTICAS DEL KIT

COMPONENTES DEL KIT

CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)

Arnés de cables: • Incluye interfaz y arnés Axxess

Adaptador de antena: • 40-EU55

Chevy Equinox 2010-2015 / GMC Terrain 2010-2014

(con pantalla monocromática)

99-3307G

A B CE FD

Desmontaje del tablero ......................................... 2

Preparación del kit ................................................ 3

Ensamble del kit

–Provisión de radio ISO DIN con cavidad.................. 4

–Provisión de radio ISO DDIN .................................. 4

Instalación de la interfase Axxess......................5-7

99-3307G

Desmontaje del tablero

1. Con la cavidad por encima de los

controles del radio de fábrica, retire

los (2) tornillos de 9/32” de dentro

de la cavidad, luego desenganche y

quite la cavidad.

2. Sin la cavidad, solo suelte a presión y

quite el panel. (Figura A)

3. Suelte a presión, desconecte y quite

todo el panel del radio/control del

clima. (Figura B)

4. Desenganche y quite los (2) paneles

del lado izquierdo y derecho del panel

de la cavidad/ranura del CD.

(Figura C)

5. Quite los (4) tornillos de 9/32” para

quitar el panel de la cavidad/ranura

del CD. Quite la toma de corriente

y fíjela a la cavidad incluida si está

instalando un solo DIN. Si va a montar

un DDIN, la toma de corriente no

se retendrá en este equipo. Quite el

botón de hule de la cavidad de fábrica

y consérvelo para el ensamblado

final. (Figura D)

6. Quite los (2) tornillos de 9/32” de

cada rejilla de aire acondicionado y

luego desenganche y quite las rejillas.

Quite los tornillos de dentro y debajo

de las cavidades de las rejillas y dos

de debajo de las ubicaciones de las

rejillas. (Esto permitirá flexibilidad en

el tablero para que quepa después el

mercado secundario). (Figura E)

7. Quite los (4) tornillos de 9/32” que

sujetan el chasis del radio para

retirarlo. (Figura F)

Continúe con la preparación del kit

(Figura A) (Figura D)

(Figura C) (Figura F)

(Figura B) (Figura E)

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios para automóviles de Metra Electronics

Metra Electronics

Metra Electronics 70-7003 Manual de servicio

Metra Electronics

Metra Electronics 87-99-3052 Manual de usuario

Metra Electronics

Metra Electronics 99-4000 Manual de usuario

Metra Electronics

Metra Electronics 99-5721 Manual de usuario

Metra Electronics

Metra Electronics 99-3303 Manual de usuario

Metra Electronics

Metra Electronics 95-5817 Manual de usuario

Metra Electronics

Metra Electronics 70-7306 Manual de usuario

Metra Electronics

Metra Electronics 95-7951 Manual de usuario

Metra Electronics

Metra Electronics 107-HY1 Manual de usuario

Metra Electronics

Metra Electronics 99-6503 Manual de usuario

Metra Electronics

Metra Electronics 99-7300 Manual de usuario

Metra Electronics

Metra Electronics 99-7424 Manual de usuario

Metra Electronics

Metra Electronics 70-6504 Manual de usuario

Metra Electronics

Metra Electronics 95-7322 Manual de usuario

Metra Electronics

Metra Electronics 99-3413 Manual de usuario

Metra Electronics

Metra Electronics 99-7503 Manual de usuario

Metra Electronics

Metra Electronics 99-8100 Manual de usuario

Metra Electronics

Metra Electronics 99-7318 Manual de usuario

Metra Electronics

Metra Electronics 99-8218 Manual de usuario

Metra Electronics

Metra Electronics 99-8205 Manual de usuario

Metra Electronics

Metra Electronics 95-7617B Manual de usuario

Metra Electronics

Metra Electronics 95-3023HG Manual de usuario

Metra Electronics

Metra Electronics 99-8903B Manual de usuario

Metra Electronics

Metra Electronics 82-3043 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario