M2 Antenna Systems 215-470LP16 Manual de usuario

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.00

Model .........................................215-470LP16

Frequency Range.......................215-470 MHz Cont.

*Gain ..........................................8.5 dBi Typical Average

Front to back ..............................27 dB Typical Average

Beamwidth..................................@230MHz E=61°/H=92°

Beamwidth..................................@350MHz E=58°/H=89°

Beamwidth..................................@450MHZ E=59°/H=90°

Feed Impedance........................50 Ohms Unbalanced

Maximum VSWR........................>1.5:1 AVG.

Mounting Polarity........................Horizontal or Vertical

Mast............................................1.5-2.0 Dia

Input Connector..........................“N” Female

Power Handling..........................250 Watts

Boom Length / Dia......................42” / 3/4” SQ

Turning Radius:..........................21”

Wind area / Survival...................0.8 Sq. Ft. / 125 MPH

Weight / Ship Wt.........................14 lbs. / 16 lbs.

M2 Antenna Systems, Inc.

Model No: 215-470LP16

FEATURES:

The 215-470LP16 is a dual boom log periodic with more elements than many conventional designs. The extra

elements help in lowering VSWR and produces higher gains across the working frequency range. The result is a high

quality commercial broad band VHF antenna. Built for extreme environmental conditions, this design uses 6061-t6 alumi-

num and all stainless hardware and UV stabilized acetyl insulation. Internal stainless screws secure the elements in

place. Optional models are available with welded elements for corrosive environments or extreme conditions. The 215-

470LP16 antenna can be ordered with many finishes, anodized, chem filmed, or a combination chem film and paint, with

many colors available.

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd

215-470LP16 DIMENSION SHEET

215-470LP16 HORIZONTAL MOUNTING

WITH HORIZONTAL

MOUNTING THE FEED

LINE CAN BE ATTACHED

TO THE LOWER BOOM

SECTION AND DOWN

THE MAST

WHEN ATTACHING

U-BOLT AND UNICRADLE

USE SIDE HOLES ON

MAST MOUNTING PLATE

HORIZONTAL MOUNTING

TO A VERTICAL MAST USING

THE SIDE MOUNT

OPTION

HORIZONTAL MOUNTING

TO A VERTICAL MAST USING

THE TOP MOUNT

OPTION

WHEN ATTACHING U-BOLTS

AND UNICRADLES

USE THE HOLES CENTERED

UNDER THE BOOM ON THE

MAST MOUNTING PLATE

215-470LP16 VERTICAL MOUNTING

NOTE THE POSITION OF THE

CONNECTOR MOUNTING

BRACKET, IT IS MOVED TO

THE REAR OF THE CABLE

ACCESS SLOT

WHEN CENTER MOUNTING ANTENNAS VERTICALLY POLARIZED IT

IS NESISARY TO MOUNT YOUR ANTENNAS ON A NON METALIC

MAST, AND FEED LINES NEED TO BE ROUTED OFF THE REAR OF

THE ANTENNA, BEHIND AND BELOW THE ELEMENTS AT LEAST 12”

FAILURE TO FOLLOW THIS PRACTICE CAN SEVELY DEGRADE THE

PERFORMANCE OF THE ANTENNA.

ATTACH THE FEED LINE

TO THE REAR BOOM

CABLE SUPPORT FOR

STRAN RELIEF OF THE

CABLE AND CONNECTOR.

NON METALLIC MAST

215-470LP16 ASSMBLY

1. Find the lower boom assembly with the cable access slot. Add the con-

nector mount bracket. Refer to the horizontal or vertical mounting options

pages to chose connector mount bracket location.

2. locate the Feedline RG-303 with connectors. Feed the SMA female con-

nector end of the cable inside the boom starting from the cable access

slot. Feed the cable thru past the front of the boom by 6”.

215-470LP16 ASSMBLY

3. Note the picture of the feed nose assembly, locate the grounded side of

the feed nose assembly. Warning The feed nose assembly when

unattached is fragile, after complete installation it will be very durable.

Care must be taken during the following steps.

4.Slide on the supplied 1/2 shrink tube onto the cable. Attach the feed

nose assembly to the end of the cable, slide the shrink tube over the mat-

ing SMA connectors and shrink.

GROUNDED

FEED NOSE

215-470LP16 ASSMBLY

5. Carefully slide the cable and feed nose assembly back into the boom

assembly, align the grounded side of the feed nose assembly with the

hole in the front of the boom assembly and add the 8-32 x 3/8 screw.

6. Add silicone sealant or equivalent around the feed nose and solder con-

nections as to seal for long term installation. Use appropriate topography

sealing techniques for long term installation.

5. Route the N connector thru the connector mount bracket, add lock

washer and nut and tighten.

215-470LP16 ASSMBLY

6. locate the front and rear delrin spreader bars. Add the both smaller front

spreader bars to either side of the boom assembly add the 8-32 screw

thru the boom and add the nut. Repeat for the rear end of the boom as-

sembly.

7. Find the upper boom section and attach to the open holes of the rear

spreader bars. Carefully bring the nose of the upper boom assembly clos-

er to the nose of the lower boom assembly, slide the center conductor side

of the feed nose assembly into the nose of the upper boom assembly and

add the 8-32 x 3/3 screw and tighten. Add the 8-32 screws to the front

spreader bars, add the nuts and tighten all the hardware.

215-470LP16 ASSMBLY

8. Locate the BTM side plate, BTM block and mast mount plate. See the

picture and assemble the BTM bracket. Add the u-bolts and

uni-cradles for your mounting style, horizontal or vertical polarity. Be sure

to tighten all hardware before installation. Always use good low loss coax

for feed line. Seal all exposed connectors with the appropriate sealing

techniques for your particular topography.

Screw, 8-32 x 1 3/4 ss

w/ lock nut

Screw, 8-32 x 1 1/2 ss

w/ lock nut

Screw, 1/4-20 x 1 3/4 ss

w/ lock nut

MAST MOUNT

PLATE

BTM SIDE

PLATE

BTM INSULATOR

PLATE

215-470LP16 PARTS & HARDWARE

DESCRIPTION...............................................................................QTY

BOOM ASSEMBLY W/ ELEMENTS, UPPER................................1

BOOM ASSEMBLY W/ ELEMENTS, LOWER...............................1

FEED NOSE ASSEMBLY ..............................................................1

FEED LINE, RG-303 W/ SMA FEMALE TO N FEMALE ...............1

CONNECTOR MOUNT BRACKET................................................1

REAR BOOM CABLE SUPPORT..................................................1

BTM SIDE PLATE..........................................................................2

BTM BLOCK...................................................................................1

MAST MOUNT PLATE...................................................................1

BTM INSULATOR PLATE2

FRONT SPREADER BAR, DELRIN2

REAR SPREADER BAR, DELRIN.................................................2

UNICRADLE, (M2AMC0076) .........................................................2

U-BOLT, 2” SS HINDLEY...............................................................2

PENETROX / ZINC PASTE CUP...................................................1

ASSEMBLY MANUAL....................................................................1

HARDWARE:

NUT,1/4-20 SS...............................................................................4

LOCKNUT, 1/4-20 SS ....................................................................2

LOCKWASHERS, 1/4 SS...............................................................4

BOLT,1/4-20X1/2,FH SCKT,SS .....................................................4

BOLT, 1/4-20X1-3/4” SS ................................................................2

SCREW, 8-32 X 1-3/4” SS .............................................................2

SCREW, 8-32 X 1-1/2 SS...............................................................6

SCREW, 8-32 X 1” SS....................................................................1

SCREW, 8-32 X 3/8” SS.................................................................4

LOCKWASER, #8 SS.....................................................................4

LOCKNUT, 8-32 SS .......................................................................9

CABLE TIE, 8” NYLON...................................................................4

SHRINK TUBE, 1/2 W/ SEALANT X 1 1/2”....................................1

ALLEN WRENCH, 5/32..................................................................1

M2ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE.

FRESNO, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

Otros manuales de Antena de M2 Antenna Systems

M2 Antenna Systems

M2 Antenna Systems 222XP30 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 8-30LP9 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 2M4 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 2MXP20 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M3FS Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 440-18 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 35.7-4 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 406-6SX Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 17M5DX Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 23CM22EZB Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 418CP30 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 41-3BB Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 300XP12 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6M5XHP Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222XP40 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems KT34M2 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 432-6WL Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 2MCP8A Manual de usuario

M2 Antenna Systems

M2 Antenna Systems FG2227-21X4CP Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 2M-440XPSS Manual de usuario

M2 Antenna Systems

M2 Antenna Systems Relay/Preamp Housing with MAP65 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M4LLDD Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 146CP8 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 249CP24 Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario