M2 Antenna Systems 35.7-4 Manual de usuario
M2 Antenna Systems, Inc.
Model No: 35.7-4
M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722
Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com
©2022 M2 Antenna Systems Incorporated
08/30/22
Rev.01
Model .........................................35.7-4
Frequency Range.......................35.4 to 36 MHz
Gain............................................10.89 dBi
Front to back ..............................22 dB Typical
Feed type ...................................“T” Match
Feed Impedance. .......................50 Ohms Unbalanced
Maximum VSWR ........................1.5:1 Typical
Input Connector..........................“N’ Connector
Power Handling ......................... 1.5 kW
Boom Length / Dia..................... 20’ / 2”
Element Length / Dia................. 188” / 7/8”-1/2”
Turning Radius: ......................... Call
Stacking Distance...................... Call
Mast Size................................... 2” to 3 ” Nom.
Wind area / Survival .................. 3.8 Sq. Ft. / 100 MPH
Weight / Ship Wt........................ 40 Lbs. / 45 Lbs.
FEATURES:
The 35.7-4 has been computer optimized from the ground up for gain and pattern covering 35.4-36 MHz. Originally
designed for Meteor Scatter and monitoring systems. The custom 1:1 Fairite balun and low loss hairpin match help
maintain high efficiency. Element ring clamps and other important components are CNC machined for maximum strength
and electrical integrity. All antenna hardware is stainless steel and the U-bolts for mounting are Zinc plated.
M2 antenna Systems, Inc., has well over 35 designs for Meteor Scatter applications covering from 39 MHz to 50 MHz. If
you have a specific requirement, please contact us for more details.
SPECIFICATIONS:
*Subtract 2.14 from dBi for dBd / FS = Free Space
35.7-4 ASSEMBLY MANUAL
1. Refer to the Dimension Sheet. Note the approximate position of each element. Slide the 2” RING CLAMPS
into their approximate positions on the boom, element channels to top. If necessary, spread the ring clamp
fingers with a flat blade screwdriver to ease movement on boom. Loosely add a 1/4-20 x 1” bolt and locknut to
fingers of all clamps.
2. Mount the “T” MATCH ASSEMBLY BLOCK to the underside of the boom using the 1/4” hole 54-3/8” from
the rear end. Secure with a single 1/4-20 x 2-1/4” bolt. Orient the two connectors towards the front. Make sure
the Driven Element ring clamp is to the rear of the “T” match block. Now slide the ring clamp up against the “T”
match block and tighten the 1/4-20 x 1” bolt and locknut to hold the clamp in position.
3. Select the two 3/4” ELEMENT SECTIONS by length specified on the Dimension Sheet for the driven
element and slide a 4-3/8” long SHORTING BAR onto each one. Position them roughly in the middle of the
tubing.
4. Slide the butt end (with hole) of each 3/4” ELEMENT SECTION halfway into a 7/8” x 30” CENTER SLEEVE
and line up holes. Slide a 1/4-20 x 1-3/4” bolt through each hole and place this assembly into the Driven
Element ring clamp channel. Add the 1/4” locknuts and tighten.
5. Add the 8-32 x 1-1/4” screw and locknut and the two 8-32 x 1/4” set screws to each SHORTING BAR. Slide
the shorting bars down onto the 1/4” “T” MATCH rods and position them according to the Dimension Sheet.
Align the rods parallel with the element sections and tighten the hardware. A 5/64 Allen wrench has been
provided for the set screws.
6. Pair up the remaining 3/4” element sections and 7/8” x 30” sleeves and mount to the ring clamps as in step
#4, following the Dimension Sheet for length.
35.7-4 DIMENSION SHEET
35.7-4 ASSEMBLY MANUAL
7. Now adjust the ELEMENT SPACING to match the Dimension Sheet. Since the Driven element is fixed, use
it as the reference for setting the position of the Reflector, 52-1/2” to the rear. Then space all Director elements
forward, using the Driven element as the reference. Dimensions given are “center to center” and can also be
used “edge to edge” when working with a measuring tape. After setting spacing of each element, align it
parallel with the Driven Element and tighten the 1/4-20 x 1” bolt.
8. Attach the balun coil to the pair of connectors on the “T” match block. Secure balun with the nylon ties
supplied (ties should be snug, but not crushing cable). Bottom connector on block is for your 50 Ohm feedline.
9. Locate the balance point of the antenna and mount the BOOM TO MAST PLATE, 6” length horizontal.
Orient for desired polarity and secure with two heavy duty 2” U-bolts, cradles, 3/8” stainless lockwashers and
nuts. Two 2” U-bolts are supplied for attaching the antenna to the mast. If the feed connector will not be
accessible after installation, connect a feedline section now that reaches at least to the boom to mast plate.
10. This completes the ASSEMBLY. When the antenna is installed in position on the mast, the main feedline
can be attached. REMEMBER to support the feedline at the antenna boom exit point and on the mast. Allow
enough slack feedline to permit full rotation of the antenna.
Carefully designed and manufactured by:
M2 Antenna Systems, Inc.
4402 N. Selland Ave.
Fresno, CA 93722
(559) 432-8873 Fax (559) 432-3059
35.7-4 PARTS & HARDWARE
DESCRIPTION QTY
BOOM SECTION, 2” x.125 x 240” STR ................................................... 1
ELEMENT SECTION, 3/4” X SEE DIMENSION SHEET.......................... 8
ELEMENT SLEEVE, 7/8” X .058 X 30” (FOR 2” RING CLAMP) .............. 4
BOOM TO MAST PLATE, .250” X 4” X 6”................................................ 1
DRIVEN ELEMENT ASSEMBLY ............................................................. 1
BALUN, RG-6........................................................................................... 1
RING CLAMP, 2”...................................................................................... 4
U-BOLT AND CRADLE, 2” HD................................................................. 4
ASSEMBLY INSTRUCTIONS .................................................................. 1
IN HARDWARE BAG
SHORTING BARS, 1/2” X 1” X 4.375” ..................................................... 2
NUT, 3/8-16 SS........................................................................................ 8
LOCKWASHER, 3/8 SPLIT RING SS ...................................................... 8
BOLT, 1/4-20 X 2-1/4” SS ........................................................................ 1
BOLT, 1/4-20 X 1-3/4” SS ........................................................................ 8
BOLT, 1/4-20 X 1” SS .............................................................................. 4
NYLOCK NUT, 1/4 SS ............................................................................. 12
SET SCREW, 8-32 X 1/4” SS .................................................................. 4
SCREW, 8-32 X 1-1/4” SS ....................................................................... 2
NYLOCK NUT, 8-32 SS ........................................................................... 2
NYLON TIE, 11” ....................................................................................... 4
ALLEN WRENCH, 5/64”........................................................................... 1
M2ANTENNA SYSTEMS, INC.
4402 N. SELLAND AVE.
FRESNO, CA 93722
(559) 432-8873 FAX: (559) 432-3059
Tabla de contenidos
Otros manuales de Antena de M2 Antenna Systems
M2 Antenna Systems
M2 Antenna Systems 2M7X Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 17M5DX Manual de usuario
M2 Antenna Systems
M2 Antenna Systems Relay/Preamp Housing with MAP65 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 75-5AS Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 146CP8 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 6M HO LOOP Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 420-450-11HP Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 436CP42UG Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 222 HO LOOP Manual de usuario
M2 Antenna Systems
M2 Antenna Systems SYSTEM SAMPLE 3 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 20M5-125 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 300XP12 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 30M3-125 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 215-470LP16 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems EB-432/RK70CM Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 303CP26 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 2MCP22 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems FGHM64 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 295XP6 Manual de usuario
M2 Antenna Systems
M2 Antenna Systems 222XP40 Manual de usuario
Manuales populares de Antena de otras marcas
Alfa Network
Alfa Network APA-L01 Manual de usuario
Naval
Naval PR-422CA Manual de usuario
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario
TERK Technologies
TERK Technologies TV44 Manual de usuario
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manual de usuario
HP
HP J8999A Manual de usuario
