M2 Antenna Systems 2MCP8A Manual de usuario

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

REV F

Model ........................................ 2MCP8A

Frequency Range ...................... 143 To 148 MHz

*Gain.......................................... 9.2 dBic

Front to back.............................. 16 dB Typical

Beamwidth ............................... 60° Circular

Elipticity...................................... >3dB

Feed type................................... “T” Match

Feed Impedance........................ 50 Ohms Unbalanced

Maximum VSWR ....................... 1.3:1 Typical

Input Connector..........................“N” Female

Power Handling ..........................1.5 kW

Boom Length / Dia......................64” / 1”

Maximum Element Length..........41-1/4”

Turning Radius: ..........................64”

Stacking Distance.......................63” High & 63” Wide

Mast Size....................................1-1/2” to 2” Nom.

Wind area / Survival ...................0.5 Sq. Ft. / 100MPH

Weight / Ship Wt.........................4 Lbs. / 7 Lbs.

M2 Antenna Systems, Inc.

Model No: 2MCP8A

FEATURES:

The 2MCP8A is a light weight, circularly polarized antenna optimized for Low Earth Orbit (LEO) satellite

communications or other applications where a small circular polarized antenna is required. Optimum match and gain are

between 143 & 148 MHz for the satellite band. Rear mounted for easy coaxial cable routing. A preamp can be mounted

close to the antenna for almost no coax loss before the preamp, maximizing your receive performance. Computer design

techniques help keep spurious side lobes low down for optimum signal to noise ratios. This antenna features the same

CNC machined, O-ring and silicone-gel sealed, driven element assemblies common to all M2 Yagi antennas. This insures

years of trouble free performance regardless of weather.

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd

2MCP8A DIMENSION SHEET

TOOL REQUIRED FOR ASSEMBLY: screwdriver, 11/32 nut driver or wrench, 7/16” and 1/2” end

wrenches and sockets, measuring tape.

Start by laying out the boom sections using the DIMENSION SHEET as a guide. Use 8-32 X 1-1/4

screws and locknuts to join sections.

Note: If mounting antenna to a standard H-frame with a T-brace kit, it is important to

install the T-brace coupling bars to antenna before elements. Refer to H-Frame and T-

brace drawings for placement and more information.

ASSEMBLING THE HORIZONTAL ELEMENTS

2. Separate elements by length into two identical sets, "H" and "V". Lay out the "H" elements by

length and position as shown the DIMENSION sheet. Start with the reflector (longest) element.

Balance it on your finger to find rough center and push on a black button insulator to about 1/2” off

center. Push the element through the hole on the boom and install the second button, snugging it

up into boom. DO NOT BOTHER ACCURATELY CENTERING the element at this time and DO

NOT INSTALL the stainless steel shaft retainers yet. It is easier to do it after all the horizontal

elements are installed in the boom.

3. Install the 3/16” rod DRIVEN ELEMENT as you did the reflector. Then continue with the installation

of the DIRECTORS. Note that the Director Elements do not consistently diminish in length

from rear to front, so pay close attention to length and position.

4. Now begin centering the elements. Use a tape measure to EQUALIZE the amount the element

sticking out on each side of the boom. Once you have all the elements centered, sight down the

element tips from the rear comparing each side. Look for any obvious discrepancies and correct if

found.

5. NOTE: The SHAFT RETAINERS, for securing the elements, should always be used for permanent

and long term antenna installations. For portable or temporary use the retainers may be left off.

The button insulators, normally a tight fit, hold the elements quite securely.

To install the stainless steel SHAFT RETAINERS, use thumb and forefinger to hold the retainer

over the end of the PUSH TUBE ( 3/8" x 3" tube, supplied in the kit), internal fingers on retainer

dished into tube. HOLD THE ELEMENT FIRMLY TO PREVENT IT FROM SLIDING OFF CENTER

and press the retainer onto the element end and continue until retainer butts on insulator button.

Locking pliers, lightly clamped up against opposite button insulator will help maintain center

reference. If you push the first retainer too far, remove element from boom, push retainer

completely off the element, and start over. Install another retainer to the opposite side of the

element. Continue installing retainers until all elements are locked in place.

6. Mount the HORIZONTAL DRIVEN ELEMENT BLOCK / ROD ASSEMBLY to the TOP of the boom

using a single 8-32 X 1-1/4" screw. Orient the block with the two balun connectors facing to rear.

Install the 8-32 x 1/4” set screws (internal Allen head - tool supplied) into the SHORTING BARS.

Slide the bars onto the Driven Element Block Rods as shown on the Dimension Sheet and tighten

the set screws.

7. Mount the JUNCTION BLOCK as shown on the Dimension Sheet. Secure with 8-32 x 1-1/4" screw.

(SEE PICTURE ON NEXT PAGE FOR MORE INFORMATION).

ASSEMBLING THE VERTICAL ELEMENTS

8. Repeat steps #2 through #5 for the Vertical elements, using the Dimension Sheet as your guide to

lengths and spacing.

2MCP8A ASSEMBLY MANUAL

9. NOTE: INSTALLATION OF THE VERTICAL DRIVEN ELEMENT BLOCK DETERMINES THE

CIRCULARITY OF THIS ANTENNA. THE ORIENTATION OF THE BLOCK FOR RHC - RIGHT

HAND CIRCULARITY - IS SHOWN ON THE DIMENSION SHEET AND HDWE. DRAWING.

Viewed from the rear of the boom (rearmost Reflector HORIZONTAL), the VERTICAL Driven

Element Block mounts to the LEFT hand side of the boom with the two Balun connectors oriented

to the BACK. Secure with 8-32 x 1-1/4” screw. Install the Shorting Bars as in step #6. For Left

Hand Circularity, mount the Vertical driven element block to the opposite side of the boom, balun

connectors to BACK.

10. Attach Baluns and Phasing lines to the Driven Element Blocks and Junction Block as shown in the

picture. Depending on model and polarity, the Vertical balun may loop around another element.

This is normal. Coil rear balun if single loop overhangs rear of boom. Form balun and phasing line

coax close to the boom and secure with nylon cable ties. Ties should be snug but not crushing or

kinking the coax. Tighten the connectors gently using a 7/16" end wrench.

11. Use good quality coax and “N” connector for your feed line. Secure feed coax near connector on

Junction Block, to provide stress relief, route to rear of boom, and secure again. Allow about 60” of

coax to hang in a loop between the rear end of the boom and the reattachment point (at least 12”

beyond element tips) on the mast or cross boom. Do not route feed line to boom to mast plate

as exiting antenna here will adversely affect circular field.

12. The boom to mast plate is normally mounted to the boom at the balance point (with feed line

attached). Use two 1" U-bolts and the stainless nuts and lock washers provided. DO NOT OVER

TIGHTEN. 2” U-bolts are provided for mounting the antenna to your NON-CONDUCTIVE 2” mast

or cross boom.

INSTALLATION TIPS

13. The 2MCP8A is a circular polarized antenna and creates a field in all planes or polarities.

Performance DETERIORATES SIGNIFICANTLY if it is mounted on a metal (conductive) mast or

cross boom. A 2” mast or cross boom of any NON-CONDUCTIVE material can be used.

Fiberglass is the prime choice for its strength and weather resistance. Mount the 2M14CP so that

element tips are at least 12” from any conductive material (mast, tower, feed line, etc.).

2MCP8A ASSEMBLY MANUAL

DRIVEN ELEMENT

ASSEMBLY

1/4λ PHASING

CABLE

1/2λ BALUN

JUNCTION

BLOCK

1/4λ PHASING

CABLE

1/2λ BALUN

DRIVEN ELEMENT

ASSEMBLY

REAR OF ANTENNA FRONT OF ANTENNA

FEED

CONNECTOR

2MCP8A PARTS & HARDWARE

DESCRIPTION QTY

BOOM SECTION #1, 1” X .058” X 32”, SOE ......................................................... 1

BOOM SECTION #2, 1” X .058” X 34.5”................................................................. 1

ELEMENTS, 3/16” ROD X Dimension Sheet.......................................................... 8

DRIVEN ELEMENT BLOCK ASSEMBLY (SADEA2MCP8A) ................................. 2

JUNCTION BLOCK (SADE0065) ........................................................................... 1

BALUN, RG-6 1/2.................................................................................................. 2

MATCHING / PHASING CABLE, 1/4 ................................................................... 2

BOOM-TO-MAST PLATE, .125” X 3” X 4” (M2APT0019)....................................... 1

U-BOLT AND CRADLE, 1-1/2" ............................................................................... 2

U-BOLT, 1”.............................................................................................................. 2

ASSEMBLY MANUAL............................................................................................. 1

IN HARDWARE BAG:

SHORTING BAR (M2ASB0090) ............................................................................. 4

BUTTON INSULATOR............................................................................................ 16

KEEPER, SS........................................................................................................... 16

NUT, 5/16-18, SS.................................................................................................... 4

LOCK WASHER, 5/16”, SS .................................................................................... 4

NUT, 1/4-20, SS...................................................................................................... 4

LOCK WASHER, 1/4”, SS ...................................................................................... 4

SCREW, 8-32 X 1-1/4”, SS ..................................................................................... 5

LOCKNUT, 8-32, SS ............................................................................................... 2

SET SCREW, 8-32 X 1/4”, SS ................................................................................ 8

7” CABLE TIE, NYLON .......................................................................................... 6

ALLEN HEAD WRENCH......................................................................................... 1

PUSH TUBE, 3/8 X 3” ............................................................................................. 1

Carefully manufactured by:

M2 ANTENNA SYSTEMS, INC.

4402 N. Selland Ave.

Fresno, CA 93722

(559) 432-8873 Fax: 432-3059

www.m2inc.com Email: [email protected]om

Tabla de contenidos

Otros manuales de Antena de M2 Antenna Systems

M2 Antenna Systems

M2 Antenna Systems 44.5-5 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 137CP14HD Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 440-460-11HD Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222-10EZ Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6M HO LOOP Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6M3 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M1L Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6.9-4CDD-125 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M4LLDD Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222 HO LOOP Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 432-12EME Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 222XP30 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 2M4X Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 432-15WL Guía de inicio rápido

M2 Antenna Systems

M2 Antenna Systems 303CP26 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 400-800-8 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 6M-3SS Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 436CP16 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M3C Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 248CP22A Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 440-6SX Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 348CP18 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 2MXP20 Manual de usuario

M2 Antenna Systems

M2 Antenna Systems 40M2C Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario