M-system JC-ECT Manual de usuario

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9043 P. 1 / 5

INSTRUCTION MANUAL

JUNCTION SLAVE

(EtherCAT) MODEL JC-ECT

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Junction slave......................................................................(1)

Mounter slider.....................................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, and connected wires, may

affect the protection level of this unit when it is inte-

grated in a panel system. The user may have to review

the CE requirements in regard to the whole system and

employ additional protective measures to ensure the CE

conformity.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%

Power consumption:

JC-ECT-4: approx. 2.0 W, JC-ECT-8: approx. 4.3 W

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 10 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

JC-ECT

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9043 P. 2 / 5

COMPONENT IDENTIFICATION

PWR+

PWR

I N

X 2

L /A

X 3

X 4

L /A

PWR

RJ-45 Modular Jack

for EtherCAT

Power Supply

Connector

Status Indicator LED PWR LED

■ MODULE TYPE: 4 (4 ports)

PWR+

PWR

L /A

X 5

X 6

L /A

X 7

X 8

I N

X 2

L /A

X 3

X 4

L /A

PWR

RJ-45 Modular Jack

for EtherCAT

Power Supply

Connector

Status Indicator LED PWR LED

■ MODULE TYPE: 8 (8 ports)

■STATUS INDICATOR LED

ID FUNCTION COLOR S TAT U S

PWR Main unit internal power Green OFF Error

ON Normal

L/A Port link / activity status Green

OFF No Link

Flickering Link and activity

ON Link without activity

Flickering 50ms-On, 50ms-Off

WIRING INSTRUCTIONS

1. PWR + Power Supply

2. PWR − Power Supply

3. FE Functional earth

Cable connector: TFMC1,5 / 5–STF–3,5

(Phoenix Contact) (included in the package)

Applicable wire size:

0.2 − 1.5 mm2;stripped length 10 mm

Recommended solderless terminal

• AI0,25−10YE 0.25 mm2(Phoenix Contact)

• AI0,34−10TQ 0.34 mm2(Phoenix Contact)

• AI0,5−10WH 0.5 mm2(Phoenix Contact)

• AI0,75−10GY 0.75 mm2(Phoenix Contact)

• A1−10 1.0 mm2(Phoenix Contact)

• A1,5−10 1.5 mm2(Phoenix Contact)

■

POWER SUPPLY

JC-ECT

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9043 P. 3 / 5

MOUNTING INSTRUCTIONS

■DIN RAIL MOUNTING

• Mounting

1) Hook the upper hook at the rear side of the base onto the

DIN rail.

2) Push the lower part of the unit in the direction of the ar-

row until the base is ﬁrmly ﬁxed to the DIN rail.

• Dismounting

1) Push down the slider using the tip of a minus screwdriver.

2) Pull out the lower part of the unit.

3) Remove the upper part of the unit from the DIN rail.

■SURFACE MOUNTING

1) Insert the mounter slider along the rail at the back of the

unit as shown below, and push in the rail until it clicks

once.

2) Fix the unit with M4 screws referring to “MOUNTING

REQUIREMENTS unit: mm (inch)” on page 5.

(Torque: 1.4 N·m)

JC-ECT

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9043 P. 4 / 5

EXTERNAL DIMENSIONS unit: mm (inch)

50(1.97) [3(.12)]

115(4.52)[4 (.18)] [4 (.18)][7 (.28)] [7 (.28)]

[4(.16)]

73(2.87)

55(2.17)

DIN RAIL

(35 mm wide)

2–4.3 (.17) dia Mtg Hole

4 (.16) deep

CONNECTION DIAGRAM

Connect the unit as in the diagram below.

In order to improve EMC performance, bond the FG terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

PWR–

PWR+

POWER (IN)

PWR–

PWR+

POWER (OUT)

–

RJ-45 modular jack

EtherCAT (IN)

EtherCAT X2 (OUT)

RJ-45 modular jack

EtherCAT X3 (OUT)

EtherCAT X4 (OUT)

RJ-45 modular jack

EtherCAT X5 (OUT)*1

EtherCAT X6 (OUT)*1

RJ-45 modular jack

EtherCAT X7 (OUT)*1

EtherCAT X8 (OUT)*1

*1. Available with JC-ECT-8 only.

JC-ECT

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9043 P. 5 / 5

MOUNTING REQUIREMENTS unit: mm (inch)

125 (4.92)

SYSTEM CONFIGURATION EXAMPLE

Note) Be sure to connect the EtherCAT master device to the EtherCAT (IN) port.

EtherCAT junction slave

(Model: JC-ECT)

EtherCAT

master device

R30NECT1

R8-NECT1

Tabla de contenidos

Otros manuales de Sistema de E/S de M-system

M-system

M-system R30NCIE1 Manual de usuario

M-system

M-system R7M-EA8/UL Manual de usuario

M-system

M-system R3S-RS4A Manual de usuario

M-system

M-system R7ML-LC2-R Manual de usuario

M-system

M-system R7F4DD-DC16B-C Manual de usuario

M-system

M-system EtherCAT R7I4DECT-1-YVF4 Manual de usuario

M-system

M-system R3-PC16A Manual de usuario

M-system

M-system R7C-DC8C Manual de usuario

M-system

M-system R7ML-LC2 Manual de usuario

M-system

M-system R3-SS8N Manual de usuario

M-system

M-system R7L-DC16B Manual de usuario

M-system

M-system R7F4DC-DAC16C-H Manual de usuario

M-system

M-system Mini-MW Series Manual de usuario

M-system

M-system R30NE1 Manual de usuario

M-system

M-system 15BX-4 Manual de usuario

M-system

M-system R7C-EC16B Manual de usuario

M-system

M-system R7E-YV2 Manual de usuario

M-system

M-system R5T-RS Manual de usuario

M-system

M-system R3-CZ4 Manual de usuario

M-system

M-system R7F4DC-DAC16D-H Manual de usuario

M-system

M-system R3-DA8C Manual de usuario

M-system

M-system R3-TS4 Manual de usuario

M-system

M-system R7HL-PA4E Manual de usuario

M-system

M-system R7C-YV4 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario