M-system M8BS2-041 Manual de usuario

M8BS2-041

P. 1 / 3EM-5478-1 Rev.3

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

package you received as below.

If you have any problems or questions with the product,

please contact M-System's Sales Ofﬁce or representatives.

n PACKAGE INCLUDES:

Installation base.......................................................(1)

n MODEL NO.

Check that model No. described on speciﬁcation label is

exactly what you ordered.

n INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, installation, connection and basic mainte-

nance procedures.

POINTS OF CAUTION

n CONFORMITY WITH EC DIRECTIVES

•This equipment is suitable for use in a Pollution Degree

2 environment and in Installation Category III, with the

maximum operating voltage 300V.

Basic insulation is maintained between the input and output.

Prior to installation, check that the insulation class of this

unit satisﬁes the system requirements.

• The equipment must be mounted inside a panel.

• The equipment must be installed such that appropriate

clearance and creepage distances are maintained to conform

to CE requirements. Failure to observe these requirements

may invalidate the CE conformity.

n POWER INPUT RATINGS

• Power input ratings are specied by the model number

sufﬁx code. Check the power input voltage for the unit on

the speciﬁcation label.

AC power: 100 – 240V AC rating: 85 – 264V, 47 – 63 Hz,

130VA min.

DC power: 24 V DC rating: 24V ±10%, 2,5A min.

n ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the

air, install the installation base inside proper housing and

ventilate it.

• Do not install the base where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

• Environmental temperature must be within 0 to 55°C or 32

to 131°F (0 to50°C or 32 to 122°F for AC power) with relative

humidity within 30 to 90% RH(30 to 85% RH for AC Power)

in order to ensure adequate life span and operation.

• Be sure that the ventilation slits are not covered with

cables, etc.

n WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

n AND ....

• The unit is designed to function as soon as power is supplied,

however, a warm up for 10 minutes is required for satisfying

complete performance described in the data sheet.

COMPONENT IDENTIFICATION

n REAR VIEW

MOUNTING REQUIREMENTS mm (inch)

INSTALLATION BASE

(for Network interface) MODEL

M8BS2

-041

INSTRUCTION MANUAL

Specifications

230 (9.06)

4–M5 SCREW

50 (1.97)

M8BS2-041

P. 2 / 3EM-5478-1 Rev.3

TERMINAL CONNECTIONS

Connect the unit referring the drawings below and the connection diagrams in the following page.

nEXTERNAL DIMENSIONS mm (inch)

• M8BS2-041-M2

1 2 34

+–+–+–+–

V.ADJ

100 (3.94)

50 (1.97)

210 (8.27)

230 (9.06)

250 (9.84)

156 (6.14)

132 (5.20) 26 (1.02) min.

AC POWER UNIT

CH1 CH4

7.2(.28)

8–M3.5

OUTPUT TERMINALS

5–M3.5 POWER

TERMINALS

CDCDCDCD

CH4CH1

ABABABAB

16–M3.5 INPUT TERMINALS

17 (.67)

CT PROTECTOR (CTR)

7.3 (.29)

6.6 (.26)

• M8BS2-041-R

1 2 34

+–+–+–+–

100 (3.94)

50 (1.97)

210 (8.27)

230 (9.06)

250 (9.84)

132 (5.20) 26 (1.02) min.

CH1 CH4

7.2(.28)

8–M3.5

OUTPUT TERMINALS

3–M3.5 POWER

TERMINALS

CDCDCDCD

CH4CH1

ABABABAB

16–M3.5 INPUT TERMINALS

17 (.67)

CT PROTECTOR (CTR)

123

92 (3.62)

POWER LED

7.3 (.29)

8.6 (.34)

M8BS2-041

P. 3 / 3EM-5478-1 Rev.3

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage across the power

terminals.

3) Installation & environment

MAINTENANCE

Power units' standard life is expected for 10 years with aver-

age ambient temperature 35°C (95°F) and 1.0A load. Contact

M-System for use in extremely different conditions.

HOW TO REPLACETHE POWER UNIT (power suffix code: M2)

1) Prepare Power Unit (switching regulator) model HDC10.

2) Turn off the power supply connected to the Power Unit.

3) Remove the wire binding and wiring connected to the

terminal 1 – 2 and 4 – 5.

4) Loosen and remove the mounting screws A(4 places).

5) Detach the Power Unit from the Installation Base.

6) Attach the new Power Unit to the Installation Base and

tighten the screws in reverse order as explained above.

Ch.1

INPUT

Ch.4

INPUT

–

POWER

UNIT

AC POWER

Ch.1

INPUT

Ch.4

INPUT

–

■ DC Power Supply ■ AC Power Supply

OUTPUT 2

Ch.1

OUTPUT

Ch.4

OUTPUT

OUTPUT 2

Ch.1

OUTPUT

Ch.4

OUTPUT

POWER

Ch.1

INPUT

Ch.4

INPUT

–

POWER

UNIT

AC POWER

Ch.1

INPUT

Ch.4

INPUT

–

■ DC Power Supply ■ AC Power Supply

OUTPUT 2

Ch.1

OUTPUT

Ch.4

OUTPUT

OUTPUT 2

Ch.1

OUTPUT

Ch.4

OUTPUT

POWER

n CONNECTION DIAGRAM

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive

remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this

warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original

sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: info@m-system.co.jp

V.ADJ

: Mounting screws with

washer, M3 x 6 (4 pls.)

: 24V DC (+)

: 24V DC (–)

: FG

: AC power input (U)

: AC power input (V)

Otros manuales de Sistema de E/S de M-system

M-system

M-system R5T-RS Manual de usuario

M-system

M-system R7C-SV4 Manual de usuario

M-system

M-system R3-CT8A Manual de usuario

M-system

M-system R1M-GH2T Series Manual de usuario

M-system

M-system R7F4HC-DAC32D-K Manual de usuario

M-system

M-system 15BX-4 Manual de usuario

M-system

M-system R3-CT8C Manual de usuario

M-system

M-system R7M-DA16F Manual de usuario

M-system

M-system R7ML-YS2-R Manual de usuario

M-system

M-system R7E-EC16B Manual de usuario

M-system

M-system R30YN16A Manual de usuario

M-system

M-system R7HL-PA4E Manual de usuario

M-system

M-system R7G4HML-6-SVF8N Manual de usuario

M-system

M-system R7D-PA8 Manual de usuario

M-system

M-system R30PA2 Manual de usuario

M-system

M-system R1M-D1 Manual de usuario

M-system

M-system R7C-YV2 Manual de usuario

M-system

M-system M6 Series Manual de usuario

M-system

M-system R7ML-SV4 Manual de usuario

M-system

M-system R3-PD16C Manual de usuario

M-system

M-system Remote I/O R8 Series Manual de usuario

M-system

M-system R7 Series Manual de usuario

M-system

M-system R7I4DML3-DA32A Manual de usuario

M-system

M-system R7D-YS2 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario