Linksys WAP54G - Wireless-G Access Point Manual de usuario

A Division of Cisco Systems, Inc.

Model No.

Wireless Quick Installation Guide

Wireless

Quick Installation Guide

Model No.

GHz

2802.11g

WAP54G ver. 2 (UK)

Access Point

Wireless-G

Package Contents

• Wireless-G Access Point

• Detachable Antennas

• Power Adapter

• Setup CD with User Guide

• Ethernet Network Cable

• Quick Installation

ALocate an optimum location

for the Access Point. The best

place for the Access Point is

usually at the center of your

wireless network, with line of

sight to all of your PCs and

wireless accessories.

BFix the direction of the

antenna. Try to place it in a

position that will best cover

your wireless network. Nor-

mally, the higher you place the

antenna, the better the perfor-

mance will be. The antenna's

position enhances the receiv-

ing sensitivity.

CConnect a standard Ethernet

network cable to the Access

Point. Then, connect the other

end of the Ethernet cable to a

switch or router. The Access

Point will then be connected to

your 10/100 Network.

DConnect the AC Power

Adapter to the Access Point's

Power Socket. Only use the

power adapter supplied with

the Access Point. Use of a dif-

ferent adapter may result in

product damage.

Connecting the Access Point

Now that you've connected the

Access Point to your wired network,

you are ready to begin setting it up.

This Setup Wizard will take you

through all the steps necessary to

configure the Access Point.

AInsert the Setup Wizard CD into

your PC's CD-ROM drive. Your

PC must be on your wired net-

work to set up the Access Point.

BThe Setup Wizard's Welcome

screen should appear on your

monitor. If it does not, this

means the Setup Wizard is not

automatically running as it

should. Start the Setup Wizard

manually by clicking the Start

button, selecting Run, and typ-

ing d:\setup.exe (where “D” is

your PC's CD-ROM drive). Click

the Setup button to continue

this Setup Wizard. Click the User

Guide button to view the User

Guide. To exit this Setup Wizard,

click the Exit button.

NOTE: The Access Point should be config-

ured through the Setup Wizard and set up

through a wired network connection.

Configuring the Access Point

CThe next screen shown displays

how the Access Point should

be connected while running

this Setup Wizard. Optimally,

you should perform this setup

through a PC on your wired

network. Click the Next button

to continue the Setup Wizard.

DThe Setup Wizard will run a

search for the Access Point

within your network and then

display a list along with the sta-

tus information for each

access point. If this is the only

access point on your network, it

will be the only one displayed.

If there are more than one dis-

played, select the Access Point

by clicking on it and click the

Yes button to continue the

Setup Wizard.

EYou will be asked to sign onto

the Access Point you've

selected. Enter the Password

you've assigned. If none has

been assigned, enter the

default password: admin.

Then, click the OK button. (This

password can be changed

from the Web-based Utility's

Password tab.)

FThe Configure Network Address

Settings screen will appear

next. Enter an IP Address, Sub-

net Mask, and the IP Address of

your network Gateway. Then,

click the Next button.

IP Address. This IP address must

be unique to your network. (The

default IP address is

192.168.1.245.)

Subnet Mask. The Access

Point's Subnet Mask must be

the same as your Ethernet net-

work.

Gateway. This IP address

should be the IP address of the

gateway device that allows for

contact between the Internet

and the local network.

GThe Wireless Settings screen

should now appear. Enter your

wireless network's SSID and

select the channel at which

the network broadcasts its wire-

less signal. Enter, also, a Device

Name to prevent any confu-

sion when using multiple

Access Points. Then, click the

Next button.

SSID. The SSID is the unique

name shared among all points

in a wireless network. The SSID

must be identical for all points

in the wireless network. It is

case sensitive and must not

exceed 32 characters, which

may be any keyboard charac-

ter. Make sure this setting is the

same for all points in your wire-

less network.

Channel. Select the appropri-

ate channel from the list pro-

vided to correspond with your

network settings. All points in

your wireless network must use

the same channel in order to

function correctly.

Device Name. The Device

Name is a unique name given

to the Access Point to prevent

confusion when using multiple

Access Points.

HThe (optional) Security Settings

screen will appear next. From

this screen, you can set the

level of encryption you desire

for your network, along with

selecting Passphrases and/or

encryption keys.

With WPA PSK, or Pre-Shared

Keys, you have two encryption

options, TKIP and AES, with

dynamic encryption keys.

Select the type of algorithm,

TKIP or AES. Enter a WPA Shared

Key of 8-32 characters.

The WEP key can consist of the

letters “A” through “F” and the

numbers “0” through “9” and

should be 10 characters in

length for 64-bit encryption or

26 characters in length for 128-

bit encryption. All points in your

wireless network must use the

same WEP key to utilize WEP

encryption.

Click the Next button to con-

tinue.

IYou should now review the set-

tings you've chosen. If these

settings are correct, click the

Yes button to save these set-

tings. If you wish to change any

of the settings, click the No but-

ton. You will exit the Setup Wiz-

ard and can start it again to

revise your settings.

WAP54G-V2-UK-QIG-40224NCKL

Linksys is a registered trademark or trademark of

Cisco Systems, Inc. and/or its affiliates in the U.S.

For additional information or troubleshooting

help, refer to the User Guide on the CD-ROM

or the Technical Support Insert. You can also

e-mail for further support.

Website

http://www.linksys.com/international

JAt this point, the configuration

performed with the Setup Wiz-

ard is complete. To configure

any other Access Points in your

network, you can run this Setup

Wizard again. Click the Exit but-

ton to exit the Setup Wizard.

A Division of Cisco Systems, Inc.

Modelnr.

Trådløs Installationsvejledning

Trådløs

Installationsvejledning

Modelnr.

WAP54G ver. 2 (DK)

Access point

Trådløs-G

Pakkens indhold

• Trådløs-G Access point

• Aftagelige antenner

• Strømforsyning

• Installations-cd med

brugervejledning (kun på engelsk)

• Ethernet-kabel

• Installationsvejledning

GHz

2802.11g

AFind en velegnet placering til

access point'et. Den bedste

placering er normalt midt i det

trådløse netværk med en fri

sigtelinje til alle dine pc'er og

det trådløse tilbehør.

BFikser antennens retning.

Forsøg at placere den i en

position, der dækker det

trådløse netværk bedst.

Normalt bliver modtage- og

sendeforhold bedre, jo højere

du placerer antennen.

Antennens position forbedrer

modtagelsen.

CTilslut et standard Ethernet-

kabel til access point'et. Tilslut

den anden ende af Ethernet-

kablet til en switch eller router.

Access point'et er derefter

tilsluttet til 10/100-netværket.

DTilslut vekselstrømsforsyningen til

strømstikket på det trådløse

access point. Brug kun den

strømforsyning, der følger med

det trådløse access point. Brug

af en anden strømforsyning

kan beskadige produktet.

Tilslutning af access point'et

Otros manuales para WAP54G - Wireless-G Access Point

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Linksys

Linksys

Linksys WAP54A - Instant Wireless - Access Point Manual de usuario

Linksys

Linksys WAP54GP - Wireless-G Access Point Manual de usuario

Linksys

Linksys Instant Broadband Series Manual de usuario

Linksys

Linksys WAP11 - Instant Wireless Network Access... Manual de usuario

Linksys

Linksys WAP54G - Wireless-G Access Point Instrucciones de funcionamiento originales

Linksys

Linksys LAPN600 Manual de usuario

Linksys

Linksys WAP51AB - Instant Wireless - Access Point Instrucciones de funcionamiento originales

Linksys

Linksys WAP11 - Instant Wireless Network Access... Manual de usuario

Linksys

Linksys Instant Broadband Series Guía

Linksys

Linksys WPG54G Manual de usuario

Linksys

Linksys LAPAC1750 Manual de usuario

Linksys

Linksys LAPN300 Manual de usuario

Linksys

Linksys WAP54GPE - Wireless-G Exterior Access Point Manual de operación

Linksys

Linksys LAPAC1750 Manual de usuario

Linksys

Linksys SPA400 Guía de configuración rápida

Linksys

Linksys LAPAC1200C Manual de usuario

Linksys

Linksys LAPAC1750PRO Manual de usuario

Linksys

Linksys WAP11 v.2.6 Manual de usuario

Linksys

Linksys WAP54G - Wireless-G Access Point Instrucciones de funcionamiento originales

Linksys

Linksys WAP200 Manual de operación

Linksys

Linksys WAP200E Manual de usuario

Linksys

Linksys WPG54G Instrucciones de funcionamiento originales

Linksys

Linksys WAP54G - Wireless-G Access Point Manual de usuario

Linksys

Linksys WAP54GX Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario