Linksys WAP54G - Wireless-G Access Point Instrucciones de funcionamiento originales

Now that you’ve connected the Access Point to your wired network, you are

ready to begin setting it up. The Setup Wizard will take you through all the

steps necessary to get the Access Point connecting your wireless network to

your wired network and communicating more efficiently.

A. Insert the Setup Wizard CD into your PC’s CD-ROM drive. Optimally,

your PC should be on your wired network.

B. The Welcome screen

should appear on your

monitor. If it does not,

this means the autorun

is not functioning.

Start the autorun man-

ually by clicking the

Start button, select-

ing Run, and typing

D:\setup.exe (if “D”

is your PC’s CD-ROM

drive). Then click the

Setup button.

WAP54G

Package Contents

• One Wireless-G Access Point with

Detachable Antennas (1)

• One Power Adapter (2)

• One Setup Wizard CD-ROM with User

Guide (3)

• One Category 5 Ethernet Network

Cable (4)

• One Quick Installation

• One Registration Card

Continued on back

This Quick Installation is meant to help you install the product quickly and easily. For detailed instructions on installation,

configuration, and further setup options, please consult the User Guide.

Instant Wireless®Series

WWiirreelleessss-GGAAcccceessssPPooiinntt

A. Locate an optimum location for the Access Point. The best place for the

Access Point is usually at the center of your wireless network, with line of

sight to all of your mobile stations.

B. Fix the direction of the antenna. Try to place it in a position that can best

cover your wireless network. Normally, the higher you place the antenna,

the better the performance will be. The antenna’s position enhances the

receiving sensitivity. Both antennas should be perpendicular to the ground

and parallel to each other.

C. Connect the included Category 5 Ethernet network cable to the Access

Point. Then connect the other end of the network cable to a switch or hub.

The Access Point will then be connected to your 10/100 network.

Connecting the Wireless-G

Access Point

D. Connect the AC power adapter to the Access Point’s Power port. Only use

the power adapter supplied with theAccess Point. Use of a different adapter

may result in product damage.

Proceed to Step 2.

Note: In order for all other wireless devices to communicate with the Access

Point, those devices must be operating in infrastructure mode. If any wireless

devices are configured in ad-hoc mode, they WILL NOT be recognized by the

Access Point.

Setting Up the Wireless-G

Access Point

Note: While the Access Point has been designed to work correctly right out

of the box, setting it up on a wireless-equipped computer will require you to

use the Linksys default settings. These settings can then be changed through

the Web-based Utility. For more details, refer to the User Guide on the Setup

Wizard CD-ROM.

C. You can configure the Access

Point through any PC con-

nected to your Ethernet net-

work. Make sure the Access

Point is connected to one of

your network switches or

hubs. Click the Next button.

D. The next screen will display a

list of access points on your

network, along with the status

information for each access

point. If there is only one

access point on your network,

it will be the only one dis-

played. If there are more than

one displayed, select the

Access Point by clicking on it,

and then click the Yes button.

E. On the Enter Network

Password screen, enter the

default password, admin, in

the Password field. Then

click the OK button. For

added security, remember to

change this password later

through the Web-based

Utility’s Password screen.

WWW.LINKSYS.COM

F. The IP Settings screen will

appear. Enter an IP Address

and Subnet Mask appropriate

to your network. Then enter a

unique name in the AP Name

field. Click the Next button.

G.The Basic Settings screen

will appear. Enter your wire-

less network’s SSID, and

select the channel at which

the network broadcasts its

wireless signal. Then click

the Next button.

H.The Security screen will

appear. Set the Wired

Equivalent Privacy (WEP)

encryption for your wireless

network. Select a WEP con-

figuration method and a

passphrase. Then click the

Next button.

I. The second Security screen

shows the WEP key. If you

entered a passphrase, then the

Key 1 field will display the

automatically generated

WEP key. If you did not enter

a passphrase, then enter a

WEP key in the Key 1 field.

Each point in your wireless

network must use the same

WEP key for the network to

function properly. Click the

Next button.

J. The next screen will allow

you to review your settings.

If these settings are correct,

click the Yes button to save

these settings. If there are

any problems with the set-

tings, click the No button to

exit the Setup Wizard.

K.At this point, the configura-

tion performed with the

Setup Wizard is complete.

To configure any other

access points in your net-

work, you can run this

Setup Wizard again. Click

the Exit button to exit the

Setup Wizard.

Congratulations! The installation of the Wireless-G Access Point is

complete.

For additional details, advanced configuration, or any other questions,

refer to the User Guide on the SetupWizard CD-ROM.

QI_WAP54G-121602NC BW

Otros manuales para WAP54G - Wireless-G Access Point

Este manual sirve para los siguientes modelos

Otros manuales de Punto de acceso inalámbrico de Linksys

Linksys

Linksys WAP51AB - Instant Wireless - Access Point Manual de usuario

Linksys

Linksys LAPAC1750PRO Manual de usuario

Linksys

Linksys WAP54G - Wireless-G Access Point Manual de usuario

Linksys

Linksys WAP54GP - Wireless-G Access Point Manual de operación

Linksys

Linksys WAP55AG - Wireless A+G Access Point Manual de usuario

Linksys

Linksys EtherFast Instant Broadband BEFW11S4 Manual de usuario

Linksys

Linksys Instant Broadband Series Guía

Linksys

Linksys WAP200E Manual de usuario

Linksys

Linksys WAP55AG - Wireless A+G Access Point Manual de usuario

Linksys

Linksys LAPAC2600 Manual de usuario

Linksys

Linksys WAP200 Manual de operación

Linksys

Linksys LAPN600 Manual de usuario

Linksys

Linksys WAP11 - Instant Wireless Network Access... Instrucciones de funcionamiento originales

Linksys

Linksys WAP55AG - Wireless A+G Access Point Instrucciones de funcionamiento originales

Linksys

Linksys WAP11 v.2.6 Manual de usuario

Linksys

Linksys WPG54G Manual de usuario

Linksys

Linksys WAP11 v2.2 Manual de usuario

Linksys

Linksys WRT610N V1 Manual de usuario

Linksys

Linksys WAP4400N Manual de operación

Linksys

Linksys LAPN300 Manual de usuario

Linksys

Linksys WAP4410N Manual de usuario

Linksys

Linksys WAP11 - Instant Wireless Network Access... Manual de usuario

Linksys

Linksys Instant Wireles Series Manual de usuario

Linksys

Linksys WAP54GP - Wireless-G Access Point Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario