Kramer VS-34FD Manual de usuario

VS-34FD Quick Start

P/N:

2900- 301348QS

Rev:

Scan for full manual

VS-34FD Quick Start Guide

This guide helps you install and use your VS-34FD for the first time.

Go to www.kramerav.com/downloads/VS-34FD to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VS-34FD 34 Flexible I/O Digital Matrix Switcher

1 Set of rack ears (attached)

1 Quick start guide

1 Power cord

Step 2: Get to know your VS-34FD

Feature

Function

keypad

Numeric

1 to 0

◄(Backward)

Press to shift the LCD display to the right (the LCD display only shows 11 of the

available matrix combinations).

►(Forward)

Press to shift the LCD display to the left (the LCD display only shows 11 of the

available matrix combinations).

Double-function

Selector Buttons

Area

Menu Button

Functions

ALL

Press to connect an input to all outputs. After pressing the MENU

button, this button lights and is enabled.

STO

Press to store the current setup in a preset. After pressing the MENU

button, this button lights and is enabled.

EDID

Press to assign EDID channels.

ESC

Press to exit the current operation.

10 11115 16

17 18 19 20

12 13 14

8 9

2 3

Feature

Function

OFF

Press to turn off an output. After pressing the MENU button, this

button lights and is enabled.

RCL

Press to recall a preset. After pressing the MENU button, this button

lights and is enabled.

DELAY

Press to set the delay between confirming an action and the execution

of the action.

ENTER

Press to complete the input-output setup when using a one-digit

number instead of two digits. For example, to enter input 5, you can

press either 05 or 5, ENTER.

Press to enter the options in a setup menu.

EXIT MENU Button

Press to exit a menu or return to switching mode.

DEFAULT SETUP Button

Press to open the reset menu on the display.

TAKE Button

Press to confirm actions.

MENU Button

Press once to enable the ALL, OFF, STO and RCL buttons.

Press again to enter the configuration menu.

When in a menu, press to cycle through the menu items.

LOCK Button

Press and hold for approximately 2 sec to lock/unlock the front panel buttons.

OUTPUTS/INPUTS

LCD Display

Displays the outputs (upper row) switched to the selected inputs (lower row).

Displays user interface messages and menus.

SERVICE Mini USB Connector

Use for controlling the matrix switcher and for firmware upgrade via K-Upload.

POWER LED

Lights yellow when the power supply is active and the device is powered on.

ERROR LED

Lights red when an error is detected. Briefly lights red immediately following a power

disruption (e.g., cable disconnection, power off, and so on).

PS-1 Power Module

Supplies power to the device.

PS-2 Power Module

Supplies power to the device.

Feature

Function

PS-2 Power Module and Switch

Connect to the mains power supply (for the PS-1 power module) and use switch to

power the unit.

PS-1 Power Module and Switch

Connect to the mains power supply (for the PS-2 power Module) and use switch to

power the unit.

You can connect PS-1 and/or PS-2.

If one of them fails to operate, the other can power the unit.

48V DC Harness Connector

Connect to the PS-4812 PoE power supply add-on.

RS-232 9-pin D-sub Port

Connect to the remote operation PC or a controller.

RESET Recessed Button

Press to reboot the VS-34FD control card.

NET 1 RJ-45 Connector

Connect to a PC or controller via the Ethernet LAN (100Mb).

NET 2-1G RJ-45 Connector

Connect to a PC or controller via the Ethernet LAN (100/1000Mb).

21 22 26

24 2825

ININ IN IN IN IN IN INOUT OUT OUT OUT OUT OUT OUT OUT OUTCTRL

2723

48V

Feature

Function

IN/OUT Connector Cards (2x17)

Insert an input or output card and connect sources/acceptors to the HDMI™ and/or

AUDIO 3.5mm mini jacks to create a flexible matrix switcher (ranging from 2x32 to

32x2).

Different card types are available.

Each port in a card operates independently.

Card slots support hot-plug connection, so the device immediately identifies a card as

IN or OUT.

AUDIO 3.5mm mini jacks can be set as inputs or outputs (the output is the HDMI

audio embedded audio) when a source/acceptor is connected.

The port numbers are fixed. Each card has 2 ports and they are numbered

accordingly (for example, in the card located under 19-20, the top port is 19 and the

lower one is 20).

Step 3: Install the VS-34FD

To rack mount the machine, attach both rack ears

(by removing the screws from each side of the

machine and replacing those screws through the

rack ears) or place the machine on a table.

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect the inputs and outputs

Insert the input and output cards into the card slots and then connect the inputs and the outputs.

You can insert IN/OUT cards into slots while the device is powered.

Always switch OFF the power on each device before connecting it to your VS-34FD.

For optimum range and performance use the recommended Kramer cables available at www.kramerav.com/product/VS-34FD.

Using third-party cables may cause damage!

Step 5: Connect the power

Connect the power cord to VS-34FD and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the

terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the

bottom of the unit.

Step 6: Set operation parameters

To operate VS-34FD via the front panel, use the

numeric keypad.

When the unit is powered-on, the last matrix setup that

was used is loaded. Use either the setup recall

(records a stored configuration from a preset) or

default setup recall (for quick retrieval of a commonly

used programmable default setup) functions to retrieve

other setups.

After switching on the power, the LCD display shows the

following screens in sequence:

Step 7: Operate the VS-34FD

Operate VS-34FD via:

•Front panel buttons.

•Remotely, by RS-232 serial commands

transmitted by a touch screen system,

PC, or other serial controller via

RS-232, USB or Ethernet port.

•Remotely, using the IR remote control

transmitter.

•Embedded web pages via the Ethernet.

RS-232 Control / Protocol 3000

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII

Stop Bits:

Example: (Switch video input 2 to output 4): #V 2>4<CR>

Default Ethernet Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.255.0

TCP Port #:

5000

Gateway:

192.168.0.1

Default User:

Admin

Default Password:

Admin

Using the embedded web pages

Click the navigation pane to open the following pages:

•Routing Settings –Change the input to output

routing.

•Authentication –Activate password security

(default = no password).

•EDID Management –Copy EDIDs from outputs

to inputs.

•Settings –Change device name and IP settings,

configure card settings and upgrade card

firmware, and perform factory reset.

•Status –Monitor operation status of cards,

power supplies, and fans.

•About –View current FW version and

manufacturer information

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Otros manuales para VS-34FD

Otros manuales de Conmutador de matriz de Kramer

Kramer

Kramer VS-44H Manual de usuario

Kramer

Kramer VP-1608 Manual de usuario

Kramer

Kramer VS-1616DN-EM Manual de usuario

Kramer

Kramer VS-88DT Manual de usuario

Kramer

Kramer VS-44H2A Manual de usuario

Kramer

Kramer VS-2516 Manual de usuario

Kramer

Kramer VS-88HDCPxl Manual de usuario

Kramer

Kramer VS-84UT Manual de usuario

Kramer

Kramer VS-1604 Manual de usuario

Kramer

Kramer VS-3232V Manual de usuario

Kramer

Kramer VS-84HN Manual de usuario

Kramer

Kramer VS-6464DN-EM Manual de usuario

Kramer

Kramer 88DS Manual de usuario

Kramer

Kramer VP-773A Manual de usuario

Kramer

Kramer VS-44HDXI Manual de usuario

Kramer

Kramer VS-88H2 Manual de usuario

Kramer

Kramer VS-88HD Manual de usuario

Kramer

Kramer Sierra Pro XL 1608V3S Manual de usuario

Kramer

Kramer VS-806YC Manual de usuario

Kramer

Kramer Sierra Video 3232V3 Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Kramer

Kramer VS-66UHD Manual de usuario

Kramer

Kramer VS-44HN Manual de usuario

Kramer

Kramer VS-88DVI Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Roland

Roland XS-1HD Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario

Extron electronics

Extron electronics MTPX Plus Series Manual de usuario

Key Digital

Key Digital Champion KD-16x16CS Manual de usuario

Shinybow USA

Shinybow USA SB-8811 Manual de usuario

Optimus

Optimus Compact Manual de usuario