KMC Controls MEP-4201 Manual de usuario

MEP-4201/4501/4901 1 Installation Guide

Installation Guide

Tri-State/Two-Position Actuators (25/45/90 in-lb.)

MEP-4201/4501/4901

Mounting 1

Wiring 2

Maintenance 2

More Information 2

Mounting

Illustration 1—Overview (Direct-Coupled Mounting)

1. Ensure the damper can move freely through its

entire range of motion, and x any binding before

installing the actuator. Turn the damper blade to

its fully closed position.

2. Press (to the right) and hold the gear disengage-

ment lever (see Illustration 1), rotate the actuator

to the fully closed position, and release the lever.

NOTE: Depending on the damper-seal design,

backing the actuator o its stop

approximately 5° may provide tight

damper shut-o.

3. Align the actuator and slide it onto the shaft.

4. Leaving a gap between the actuator and

mounting surface to prevent any binding, nger-

tighten the nuts on the V-bolt.

5. Insert the provided (HMO-4001/4002, dependent

on model) non-rotation bracket into the slot at the

base of the actuator and secure the non-rotation

bracket with two #8 or #10 self-tapping screws.

6. Evenly tighten the V-bolt nuts (30–35 in-lb.

on MEP-4201 model or 60–70 in-lb. on MEP-

4501/4901).

7. If desired, use a 7/64-inch hex key wrench to

loosen and position the end-stop screw.

NOTE: The two holes at the top of the actuator

are NOT for use in direct-coupled

applications. (They are for remote

mounting, such as with the optional

HLO-4001 Crank Arm Kit.) For mounting

to valves, see the appropriate valve

installation guide.

Gear

Disengagement

Lever

HMO-4002

Non-Rotation

Bracket

Mounting

Surface

1.625

(41.3)

6.000

(152.4)

3.406

(86.5)

Adjustable

Stop

° Rotation

Indicators

1.563

(39.7)

2.812

(71.4)

Gear

Disengagement

Lever

Removeable Conduit Fitting with

(2)1/2" NPS Threaded Holes (for

use with flexible conduit only)

HMO-4001 Non-Rotation “T”

Bracket included with MEP-4901

HMO-4002 Non-Rotation

Bracket included with

MEP-4201& MEP-4501

MEP-4201/4501/4901 2 Installation Guide

Power/Signal

Terminal Block

(Under Conduit Fitting)

Selector

Switches Illustration 5—Tri-State Floating Point Control

Illustration 3—Two-Position Control (3-Wire), CCW Leg

Illustration 4—Two-Position Control (3-Wire), CW Leg

Wiring

To wire the actuator:

1. Loosen the screw on the conduit ing and lift up

to remove the ing.

2. Using a utility knife or drill, cut the hole plug

to accept wiring or replace the plug with an

application-specic ing.

NOTE: The hole plugs (or similar ings) protect

internal components from debris. To

guarantee an IP54 rating, install an HMO-

4521 cord grip or HPO-4051 cable kit.

3. Thread wires through the plugged opening and

connect to the terminal block according to the

relevant application. (See Illustrations 3 through

5.) Adjust the selector switch as needed.

4. Reinstall the conduit ing and tighten the screw.

Illustration 2—Wiring Compartment

KMC Controls, Inc.

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com; [email protected]

Maintenance

No routine maintenance is required. Careful

installation will ensure long term reliability and

performance.

More Information

–Power Supply

24VAC/VDC

CCW

COM

~/+

–

Switch Position

1 2

–Power Supply

24VAC/VDC

Contact Position:

Closed = CCW Rotation

CCW

COM

~/+

Open = CW Rotation

Switch Position

1 2

–Power Supply

24VAC/VDC

Contact Position:

Closed = CW Rotation

CCW

COM

~/+

Open = CCW Rotation

Switch Position

1 2

Important Notices

The material in this document is for information

purposes only. The contents and the product it

describes are subject to change without notice.

KMC Controls, Inc. makes no representations or

warranties with respect to this document. In no event

shall KMC Controls, Inc. be liable for any damages,

direct or incidental, arising out of or related to the

use of this document.

For models, specications, and

additional information, see

the MEP-4201/4501/4901 Series

Data Sheet on the KMC web

site.

For accessories, troubleshoot-

ing, torque selection, links to

sample applications, and other

information, see the MEP-4xxx

Applications Guide on the

KMC web site.

Este manual sirve para los siguientes modelos

Otros manuales de Controladores de KMC Controls

KMC Controls

KMC Controls CSC 3000 Series Guía del usuario

KMC Controls

KMC Controls MEP-4201 Manual de usuario

KMC Controls

KMC Controls MEP-5062 Manual de usuario

KMC Controls

KMC Controls CSC-3501 Manual de usuario

KMC Controls

KMC Controls BAC-7302 Instrucciones de funcionamiento

KMC Controls

KMC Controls KMD-5210 Instrucciones de funcionamiento

KMC Controls

KMC Controls CSC 3000 Series Guía del usuario

KMC Controls

KMC Controls BAC-5901C-AFMS Manual de usuario

KMC Controls

KMC Controls MEP-46 Q Series Manual de usuario

KMC Controls

KMC Controls MCP-1160 Series Manual de usuario

KMC Controls

KMC Controls SimplyVAV BAC-8205 Manual de usuario

KMC Controls

KMC Controls MEP-1500 Series Manual de usuario

KMC Controls

KMC Controls MEP-7 Series Guía del usuario

KMC Controls

KMC Controls BAC-7401 Instrucciones de funcionamiento

KMC Controls

KMC Controls BAC-7003 Manual de usuario

KMC Controls

KMC Controls BAC-7001 Manual de usuario

KMC Controls

KMC Controls FlexStat BAC-120063CW-ZEC Manual del operador

KMC Controls

KMC Controls KMD-5205 Instrucciones de funcionamiento

KMC Controls

KMC Controls KMDigital KMD-5290E Instrucciones de funcionamiento

KMC Controls

KMC Controls MCP-1040 Series Manual de usuario

KMC Controls

KMC Controls BAC-4000 series Guía del usuario

KMC Controls

KMC Controls KMD-5290 Manual de usuario

KMC Controls

KMC Controls KMD-5831 Instrucciones de funcionamiento originales

KMC Controls

KMC Controls BAC-9001CE Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario