KMC Controls MCP-1060 Series Manual de usuario

MCP-1060 Series 1 Installation Guide

Installation Guide

6" Pneumatic Damper Actuator

MCP-1060 Series

Mounting

The MCP-1160 series actuator MUST be mounted on

a rigid surface due to the force generated at, or near,

maximum air pressure.

1. Align the actuator with the controlled device. The

mounting joint allows the actuator to be located

in a dierent plane from the controlled device.

2. Aach the actuator to the rigid surface.

3. Adjust the crank arm assembly length (see the

chart) to provide the (minimum 60° to maximum

120°) rotation as required.

4. Do NOT tighten the universal joint. The actuator

must be free to swivel as it operates.

5. See the Connection section on the next page.

All dimension are in inches (mm)

CAUTION

Pneumatic devices must be supplied with clean, dry

control air. Any other medium (e.g., oil or moisture

contamination) will cause the device to fail.

CLEVIS

FEEDBACK SPRING

ALTERNATE

FEEDBACK

SPRING

CRANK ARM

BRACKET

MOUNTING POST

(Not Included)

MCP-1060 Series 2 Installation Guide

Important Notices

The material in this document is for information pur-

poses only. The contents and the product it describes

are subject to change without notice. KMC Controls,

Inc. makes no representations or warranties with respect

to this document. In no event shall KMC Controls, Inc.

be liable for any damages, direct or incidental, arising

out of or related to the use of this document.

Maintenance

No routine maintenance is required. However,

care should be taken during any installation or

maintenance due to the power of the actuator. Each

component is designed for dependable, long-term

reliability, and performance. Careful installation will

also ensure long-term reliability and performance.

Adjustments and Calibration

DANGER

The MCP-1060 contains a large powerful spring.

Exercise extreme caution if disassembly is required.

The actuator shaft MUST be restrained to prevent

the spring from expanding.

To change the positioner start-point:

1. Apply the desired signal pressure.

2. Rotate the start-point adjuster until the actuator

starts to stroke.

More Information

For specications and other information about the

actuators, see the MCP-1160 Series Data Sheet on

the KMC web site. For information about the posi-

tioner, see CMC-1001 Data Sheet.

KMC Controls, Inc.

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com

[email protected]

Connections

NOTE: Use 1/4" (6 mm) O.D. FR polyethylene

tubing and only clean, dry control air.

NOTE: MCP-1160 models ordered with CMC-1001

positioners are factory-piped between the

positioner and the actuator.

1. Connect the input control signal to the actuator

port (if no positioner is used) or to the positioner

(CMC-1001 input) Port 2(see the diagram).

2. Connect the main air (20 psi) to the positioner

(CMC-1001 center) port.

3. If a positioner is not factory-piped to the actuator,

connect the actuator input port to positioner

(CMC-1001 output) Port 1.

NOTE: If the application requires operation near

the maximum temperature and maximum

pressure, add a tubing restraint to the

actuator connection.

The MCP-1160 contains an 8-13 psi spring. A CMC-

1001 positioner allows the unit to operate over any 5

psi span with the start-point adjustable from 3-10 psi.

Replace the 5 psi spring with a 7 or 10 psi spring to

widen the span.

Otros manuales de Controladores de KMC Controls

KMC Controls

KMC Controls SimplyVAV BAC-8001 Manual de usuario

KMC Controls

KMC Controls MCP-1020 Series Manual de usuario

KMC Controls

KMC Controls MEP-4201 Manual de usuario

KMC Controls

KMC Controls SimplyVAV BAC-8205 Manual de usuario

KMC Controls

KMC Controls CSC-3501 Manual de usuario

KMC Controls

KMC Controls MEP-4 Series Guía del usuario

KMC Controls

KMC Controls KMD-5205 Instrucciones de funcionamiento

KMC Controls

KMC Controls MEP-1500 Series Manual de usuario

KMC Controls

KMC Controls BAC-7003 Manual de usuario

KMC Controls

KMC Controls KMDigital KMD-5290E Instrucciones de funcionamiento

KMC Controls

KMC Controls BAC-5900 Series Manual de usuario

KMC Controls

KMC Controls BAC-4000 series Guía del usuario

KMC Controls

KMC Controls AppStat Manual de usuario

KMC Controls

KMC Controls MEP-5062 Manual de usuario

KMC Controls

KMC Controls KMD-5290 Manual de usuario

KMC Controls

KMC Controls CSC 3000 Series Guía del usuario

KMC Controls

KMC Controls CSC-1001 Manual de usuario

KMC Controls

KMC Controls KMD-7001 Instrucciones de funcionamiento originales

KMC Controls

KMC Controls CEE-3009 Manual de usuario

KMC Controls

KMC Controls MEP-46 Q Series Manual de usuario

KMC Controls

KMC Controls CSC-2000 Series Manual de usuario

KMC Controls

KMC Controls KMD-5831 Instrucciones de funcionamiento originales

KMC Controls

KMC Controls CTE-3017 Manual de usuario

KMC Controls

KMC Controls CSC 3000 Series Guía del usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario