Klein Tools CL2500 Manual de usuario

ENGLISH

www.kleintools.com

Instruction

Manual

For Professionals...Since 1857

CL2500

• 1000A AC/DC

• TRUE RMS

• DC ZERO

• BACKLIGHT

• WORKLIGHT

• BAR GRAPH

• MAX /MIN /HOLD

• 3-5/6 DIGIT

5999 COUNT LCD

• AUTO /MANUAL

RANGE

• NON CONTACT

VOLTAGE TESTER

TRMS

ENGLISH

CL2500

Instruction Manual

GENERAL SPECIFICATIONS

The Klein Tools CL2500 is a True RMS, auto-ranging clamp meter.

It measures AC /DC voltage, AC /DC current, resistance, capacitance,

frequency, and duty cycle. It can also test non-contact voltage, diodes,

and continuity.

• Operating Altitude: 2000 meters

• Storage Altitude: 10000 meters

• Humidity: 0% to 80% at 32°F to 95°F (0°C to 35°C)

0% to 70% at 32°F to 131°F (0°C to 55°C)

• Operating Temperature: 0°C / 32°F to 40°C / 104°F < 75% R.H.

• Storage Temperature: -20°C /-4°F to 60°C /140°F

• Accuracy Temperature: 18°C /64°F to 28°C /82°F

• Temperature Coefﬁcient: 0.1*(speciﬁed accuracy) /°C

• Dimensions: 8.09" x 2.56" x 1.38"

• Weight: 13.6oz.

• Calibration: Accurate for one year

• Certiﬁcations: UL & cUL standard UL3111-1 Listed

• Pollution Degree: 2

• CAT Rating: CAT IV 600V, CATIII 1000V

• Accuracy: ± (% of reading + # of least signiﬁcant digits)

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring

a known voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms, or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Ensure meter leads are fully seated, and keep ﬁngers away from

the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes

are connected.

• Use caution when working with voltages above 60V DC,

or 25V AC RMS. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock,

replace batteries if a low battery indicator appears.

• Unless measuring voltage or current, shut off and lock out

power before measuring resistance or capacitance.

• Always adhere to local and national safety codes. Use individual

protective equipment to prevent shock and arc blast injury where

hazardous live conductors are exposed.

SYMBOLS

AC Alternating Current Warning or Caution

DC Direct Current Dangerous levels

DC/AC Voltage or Current Double Insulated Class II

Ground Safe for disconnect

from live conductors

AC Source

FEATURE DETAILS

A. Use CAT IV 600 rated leads or higher.

Do not attempt to measure more than 1000V DC or 750V AC or 2000µA.

B. Keep hands below line when measuring high current levels.

C. Auto Power-Off (Apo)

• Device will power off after 30 minutes non-use.

• Turn the dial or press a button to wake.

• Disabled during Max / Min function.

• Holding Select button while turning on disables Auto Power-Off.

D. Select Functionality Button

• Quick press (<0.5 sec):

»Switch between AC and DC.

»Switch between and .

• Long press (>1 sec):

»Switch between AC, Frequency, and Duty Cycle modes.

»Zero the DC current clamp reading.

E. Hold /Backlight /Worklight

• Press to hold the current input on the display.

• Press again to return to live reading.

• Press for 2 seconds to enable / disable lights.

• Using lights decreases battery life.

F. Auto /Manual Range

• Press repeatedly to cycle through manual ranges.

• Press for 2 seconds to return to auto ranging mode.

• AT is displayed on LCD only during auto ranging mode.

G. Max /Min Hold

• Press to enter Max /Min mode; the largest and smallest

values will be saved while in this mode.

• Press repeatedly to alternate between the maximum and minimum readings.

• Press for 2 seconds to return to live reading and clear

the stored maximum and minimum values.

H. I. Battery Replacement

• When indicator is displayed on the LCD, batteries must be

replaced.

• Remove the back screw and replace 2 x AAA batteries.

J. Magnetic Back

• Attach instrument to metal for hands-free use.

K. Bar Graph

• The bar graph shows an approximate analog representation

of a measurement.

• The bar graph responds much faster than the digital display.

• The scale of the bar graph is zero to the maximum reading of

the selected range.

FUNCTION INSTRUCTIONS

1. AC /DC Current (large): < 1000A

Features:

ZERO (DC)MAX/MINRANGEHOLD

• Center wire in guides for best accuracy.

• Opposing currents cancel (use line-splitter when necessary).

2. AC /DC Current (small): <2000µA

Features:

MAX/MINRANGEHOLD

• Select AC or DC current source.

• Current above 2000µA will damage instrument.

3. AC /DC Voltage: <750V AC or 1000V DC

Features:

MAX/MINRANGEHOLD

• Select AC or DC voltage source.

5. Resistance:

<60MΩ

Features:

MAX/MINRANGEHOLD

4. Frequency (Hz) /Duty Cycle (See Feature Details)

Features:

HOLD

• Select , , or setting.

• Do not measure resistance on a live circuit.

6. Capacitance:

<6000µF

Features:

HOLD

• Safely discharge capacitor before measurement.

• Reading may take up to 60 seconds for large capacitors.

7. Diode /Continuity

Display shows:

• Forward voltage drop if forward biased.

• “O.L.” if reverse biased.

Diode Features:

• Display shows resistance.

• Buzzer sounds if less than 40Ω.

Continuity Features:

HOLD MAX/MIN

ENGLISH

8. Non Contact Voltage (NCV): >25V AC

SYMBOLS USED ON LCD

AC Measurement DC Measurement

Negative DC Value

Auto Range Active

.L.

Overload: Range Exceeded Apo

Auto Power-Off Active

Low Battery

HOLD

Hold Active

MIN

Minimum Reading

Maximum Reading

Duty Cycle Mode Frequency Mode

Voltage Measurement

Current in Amps

Resistance in Ohms Diode Test

Capacitance in Farads Continuity Test

Relative / Zero Mode

Nano 10

-9

Micro 10

-6

Milli 10

-3

Kilo 10

Mega 10

ELECTRICAL SPECIFICATIONS

DC Voltage Measurement

Range Resolution Accuracy

600mV ˜ 600V 0.1mV ˜ 0.1V ± (0.5% + 4 digits)

1000V 1V ± (0.8% + 10 digits)

Overload Protection: 1000V

AC Voltage Measurement

Range Resolution Accuracy

600mV ˜ 750V 0.1mV ˜ 1V ± (2.0% + 5 digits)

Overload Protection: 750V RMS

Frequency Response: 45 to 400 Hz

Minimum Voltage for Frequency Measurement: 200mV

Response: True RMS

DC Current Measurement

Range Resolution Accuracy

600µA 0.1µA ± (1.2% + 3 digits)

2000µA 1µA

60A 0.01A ± (2.5% + 15 digits)

600A ~ 1000A 0.1A ~ 1A ± (1.5% + 8 digits)

Overload Protection:

• Voltage: 600V RMS

• Current: 2000µA (leads), 1000A (clamp)

AC Current Measurement

Range Resolution Accuracy

600µA 0.1µA ± (2.0% + 5 digits)

2000µA 1µA ± (1.5% + 5 digits)

60A 0.01A ± (2.9% + 15 digits)

600A ~ 1000A 0.1A ~ 1A ± (1.9% + 8 digits)

Overload Protection:

• Voltage: 600V RMS

• Current: 2000µA (leads), 1000A (clamp)

Frequency: 45 to 400Hz

Minimum Current for Frequency Measurement: 400µA (leads) or 20A (clamp)

Response: True RMS

Resistance Measurement

Range Resolution Accuracy

600Ω˜6MΩ0.1Ω˜0.001MΩ± (1.0% + 4 digits)

60MΩ0.01MΩ± (2.0% + 4 digits)

Overload Protection: 600V RMS

Capacitance Measurement

Range Resolution Accuracy

60nF ˜6000µF 0.01nF ˜1µF ± (3.5% + 6 digits)

Overload Protection: 600V RMS

Frequency Measurement

Range Resolution Accuracy

99.99Hz ˜499.9kHz 0.01Hz ˜100Hz ± (0.1% + 4 digits)

Overload Protection: 600V RMS

Duty Cycle Measurement

Range Resolution Accuracy

0.1 ˜99.9% 0.1% ± (0.2% per kHz + 0.1% + 5 digits)

Overload Protection: 600V RMS

Diode Test

Overload Protection Range Test Current Open Circuit Voltage

600V RMS 6.0V Appx. 0.25mA <1.8V DC

Continuity Test

Overload Protection Open Circuit Voltage Threshold (Appx.)

600V RMS <0.44V ~40Ω

Non Contact Voltage Detector

On Voltage

Appx. 25V AC and above

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-877-775-5346

www.kleintools.com 139677



WARRANTY

This product is warranted to be free from defects in materials and workmanship

for a period of two years from the date of purchase. During this warranty period,

Klein Tools has the option to repair or replace or refund the purchase price of

any unit which fails to conform to this warranty under normal use and service.

This warranty does not cover damage which occurs in shipment or failure which

results from alteration, tampering, accident, misuse, abuse, neglect, or improper

maintenance. Batteries and damage resulting from failed batteries are not

covered by warranty. A purchase receipt or other proof of original purchase date

will be required before warranty repairs will be rendered.

Any implied warranties, including but not limited to implied warranties of

merchantability and ﬁtness for a particular purpose, are limited to the express

warranty. Klein Tools shall not be liable for loss of use of the instrument or other

incidental or consequential damages, expenses, or economic loss, or for any

claim or claims for such damage, expenses or economic loss.

Some states or countries laws vary, so the above limitations or exclusions may

not apply to you. This warranty gives you speciﬁc legal rights, and you may also

have other rights which vary from state to state. If your Klein product requires

repair or for information on how to exercise your rights under the terms of this

warranty, please contact Klein Tools at 1-877-775-5346.

CLEANING

Turn instrument off and disconnect test leads. Clean the instrument by using

a damp cloth. Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when instrument is not in use for a prolonged period of

time. Do not expose to high temperatures or humidity. After a period of storage

in extreme conditions exceeding the limits mentioned in the Speciﬁcations

section, allow the instrument to return to normal operating conditions before

using it.

DISPOSAL /RECYCLE

Caution: This symbol indicates that equipment and its accessories

shall be subject to a separate collection and correct disposal.

Tabla de contenidos

Otros manuales de Instrumento de medición de Klein Tools

Klein Tools

Klein Tools ET300 Manual de usuario

Klein Tools

Klein Tools CL3000 Manual de usuario

Klein Tools

Klein Tools CL700 Manual de usuario

Klein Tools

Klein Tools IR2000A Manual de usuario

Klein Tools

Klein Tools CL320 Manual de usuario

Klein Tools

Klein Tools CL320 Manual de usuario

Klein Tools

Klein Tools CL310 Manual de usuario

Klein Tools

Klein Tools CL330 Manual de usuario

Klein Tools

Klein Tools CL210E Manual de usuario

Klein Tools

Klein Tools MM500 Manual de usuario

Klein Tools

Klein Tools CL312 Manual de usuario

Klein Tools

Klein Tools CL390 Manual de usuario

Klein Tools

Klein Tools 935DAF Manual de usuario

Klein Tools

Klein Tools CL310 Manual de usuario

Klein Tools

Klein Tools CL900 Manual de usuario

Klein Tools

Klein Tools 935DAA Manual de usuario

Klein Tools

Klein Tools ET200 Manual de usuario

Klein Tools

Klein Tools VDV500-123 Probe-Pro Manual de usuario

Klein Tools

Klein Tools CL900 Manual de usuario

Klein Tools

Klein Tools ET920 Manual de usuario

Klein Tools

Klein Tools NCVT-1XTKIT Manual de usuario

Klein Tools

Klein Tools ET450 Manual de usuario

Klein Tools

Klein Tools CL445 Manual de usuario

Klein Tools

Klein Tools ET130 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario