Klein Tools VDV501-089 Manual de usuario
VDV Distance
Meter
VDV501-089
Instruction
Manual
ENGLISH
UÊ
/Ê-1, /
UÊ
*,-/Ê",Ê"" Ê-
UÊ
,Ê*1Ê ÊÊ" /",Ê
UÊ
1/"Ê*"7,"
Español pg. 6
Français pg. 12
www.kleintools.com
ÀÊ*ÀviÃÃ>ð°°-ViÊ£nxÇ
®
SEL
Short
ft m
pf/
User
RG-6
RG-59
Cat5e
Cat6
READY
Cat3
RG-11
Voltage!
ENGLISH
2
-,*/"
The Klein Tools Distance Meter determines the length of a particular cable
by measuring the total capacitance of the cable attached to the unit and
comparing that to a preset or user defined capacitance per foot variable.
The Klein Tools Distance Meter has two alligator clip leads, an RJ-style
twisted pair plug and a coaxial F-connector jack for input into the meter.
The unit comes pre-programmed with nominal length constants for the
following cables:
UÊ
,xÊV>Ý>
UÊ
,ÈÊV>Ý>
UÊ
,££ÊV>Ý>
UÊ
>ÌÎÊÌÜÃÌi`Ê«>À
UÊ
>ÌxiÊÌÜÃÌi`Ê«>À
UÊ
>ÌÈÊÌÜÃÌi`Ê«>À
User mode allows the user to adjust the capacitance per foot constant,
based on the cable that needs to be tested.
The Klein Tools Distance Meter is powered by a standard 9V battery.
,Ê-*/" -
UÊ
iÃÃ\
4.9" x 2.7" x 1.4" (12.3 x 6.9 x 3.5 cm)
UÊ
7i}Ì\Ê
7.5 oz. (213 g) with battery
UÊ
"«iÀ>Ì}Ê/i«iÀ>ÌÕÀi\
0°C / 32°F to 50°C / 122°F
UÊ
-ÌÀ>}iÊ/i«iÀ>ÌÕÀi\
-20°C / -4°F to 60°C / 140°F
UÊ
Õ`ÌÞ\Ê
10% to 90%, non-condensing
UÊ
>ÕÌÊ6ÌÊ/iÀ>Vi\
Reports voltage present up to 20 volts AC or DC
UÊ
>ÌÌiÀÞÊvi\
9V Alkaline Battery, typical
UÊ
VÌÛi\
425 hours
UÊ
-Ì>`LÞ\
4 years
UÊ
i}ÌÊi>ÃÕÀiiÌ
UÊ
iÌ`\Ê
Capacitance
UÊ
,iÃÕÌ\Ê
1 ft
(0.3 meter)
UÊ
i}ÌÊÃÌ>ÌÊ,>}i\
10 to 40pF/ft (33 to 132pF/meter)
UÊ
VVÕÀ>VÞÊÜÌÊÜÊi}ÌÊVÃÌ>Ì®\Ê
ÊÊ
+/-5% plus +/-1ft (+/-5% plus +/-0.3 m)
UÊ
>ÝÕÊ,>}i\
1500 ft / 450m on most cables
//,9Ê,* /
UÊ
To replace the battery, lightly pry off the bottom rubber cover,
and disconnect the leads.
UÊ
The device will turn itself off after five minutes of non-use.
UÊ
The Battery Icon will flash if voltage drops below 6V, and turn
unit off after voltage drops below 5V.
VDV Distance Meter
ÃÌÀÕVÌÊ>Õ>
Î
7, -
To ensure safe operation and service of the tester, follow these
instructions. Failure to observe these warnings can result in severe injury
or death.
The VDV Distance Meter is not designed to work on live electrical circuits.
Do not under any cirumstances connect this device to live circuits. If a
voltage is detected, the device will be disabled until the voltage is removed.
SYMBOLS:
Warning: Potential for personal injury.
Caution: Potential for damage or destruction to equipment.
Caution: Potential for damage or destruction to equipment.
Always wear approved eye protection.
Do NOT use on energized circuits.
Conformité Européenne. Conforms with European
Economic Area directives.
Do not place equipment and its accessories in the trash.
Items must be properly disposed of in accordance with
local regulations.
local regulations.
-Ê"*,/"
UÊ
The
*"7,
button turns the unit on and off with a short press.
UÊ
To change cable presets, press the
SEL
button, and scroll with the
1*
and
"7
arrows.
UÊ
All preconfigured Cable Modes and “User” Mode are scrolled through
by pressing
1*
or
"7
buttons. Pressing the
SEL
button selects
a mode and the “Ready” icon will display on the screen to take a
measurement automatically, no other action is required.
UÊ
To switch between imperial and metric units, hold the
1*
and
"7
arrow keys together for one second.
/-/ ÊÊ
UÊ
Attach the cable to be tested to the product using the appropriate
jack or connector.
UÊ
If necessary, change to the appropriate Cable Mode as detailed above.
The “Ready” icon will appear and a measurement will be taken of the cable
length automatically. This measurement is updated every five seconds.
UÊ
If the cable is shorted, the “Short” icon is displayed.
1-,Ê"
UÊ
If “User” Mode is selected the “Ready” icon will display along with
readings for pF (capacitance per foot) and a length measurement.
UÊ
The
1*
and
"7
buttons will change the pF constant upwards or
downwards. Holding the
1*
or
"7
buttons will allow the constant
to be changed more quickly.
UÊ
With a cable sample of known length, a user can adjust the pF
constant until the indicated length measurement matches the actual
cable length. Then this setting can be used to measure other cables
of the same type. This pF value is saved until changed again in “User”
Mode or battery replacement resets the unit.
UÊ
The distance for this mode is updated every second.
UÊ
TIP: Using a longer calibration cable will reduce the error in
subsequent tests.
SEL
ENGLISH
4
-, Ê1 /" -
°
i}ÌÊ`V>ÌÀ\
Displays length of cable being measured. Blinking
dashes mean the cable length or total capacitance has exceeded the
maximum limits of the unit. When using a preset value, this will update
every 5 seconds. When in “User” Mode, this will update every 1 second.
°ÊVÌÛiÊ>LiÊ*ÀiÃiÌÊV\
Displays the selected preset cable
value or “User” Mode.
°Ê,i>`ÞÊV\
When lit, indicates that the unit is ready to take a length
measurement.
°Ê-ÀÌÊV\Ê
Indicates whether the cable being tested has a short.
°Ê1ÌÊvÊi>ÃÕÀiiÌ\
Indicates the unit of measurement (feet or
meters) currently being used to display the measurement. To switch
between metric and imperial units, hold the
1*
and
"7
arrow
keys for one second.
°Ê6Ì>}iÊV\Ê
When lit, indicates that a voltage is present in the cable
being tested. The unit is disabled when this icon is lit. Immediately
disconnect the unit from the cable and disconnect the cable from the
voltage source.
NOTE: The absence of the “Voltage!”
symbol DOES
NOT necessarily mean that there are 0 volts on the line.
°Ê>«>VÌ>ViÊ«iÀÊÕÌÊi}ÌÊVÃÌ>Ì\
In “User” Mode, the pF
constant will be displayed. Use the
1*
or
"7
arrow keys to adjust
this value.
°Ê>ÌÌiÀÞÊ`V>ÌÀ\
This will flash when the battery drops below 6V.
Replace the battery at this point.
9*
1*É"7
UÊ
Use these buttons to cycle through cable presets and
“User” Mode.
UÊ
In “User” Mode, use these buttons to adjust the
capacitance per unit length constant
SEL
UÊ
In a testing mode (preset or user) press this to exit and
select a new mode.
UÊ
When a new mode is chosen, press again to re-enter
testing mode.
*"7,
UÊ
Short press to turn the unit on or off.
Short
ft m
pf/
User
RG-6
RG-59
Cat5e
Cat6
READY
Cat3
RG-11
Voltage!
E
G
H
ltage!
x
7,, /9
This product is warranted to be free from defects in materials and
workmanship for a period of two years from the date of purchase.
During this warranty period, Klein Tools has the option to repair or
replace or refund the purchase price of any unit which fails to conform
to this warranty under normal use and service. This warranty does not
cover damage which occurs in shipment or failure which results from
alteration, tampering, accident, misuse, abuse, neglect, or improper
maintenance. Batteries and damage resulting from failed batteries are
not covered by warranty. A purchase receipt or other proof of original
purchase date will be required before warranty repairs will be rendered.
Any implied warranties, including but not limited to implied warranties
of merchantability and fitness for a particular purpose, are limited to the
express warranty. Klein Tools shall not be liable for loss of use of the
instrument or other incidental or consequential damages, expenses, or
economic loss, or for any claim or claims for such damage, expenses or
economic loss.
Some states or countries laws vary, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to
state. If your Klein product requires repair or for information on how
to exercise your rights under the terms of this warranty, please contact
Klein Tools at 1-800-553-4676.
Turn instrument off and disconnect any cables. Clean the instrument by
using a damp cloth. Do not use abrasive cleaners or solvents.
-/",
Remove the batteries when instrument is not in use for a prolonged
period of time. Do not expose to high temperatures or humidity. After a
period of storage in extreme conditions exceeding the limits mentioned
in the
Specifications
section, allow the instrument to return to normal
cations
operating conditions before using it.
-*"-ÊÉÊ,9
This symbol indicates that equipment and its accessories
shall be subject to a separate collection and correct disposal.
1-/",Ê-,6
Ê/""-]Ê °
U
{xäÊ`Ê-ÌÀiiÌÊ
UÊ
VÃÀi]ÊÊÈääÈ
£nääxxÎ{ÈÇÈÊUÊ
www.kleintools.com
Otros manuales para VDV501-089
1
Tabla de contenidos
Otros manuales de Instrumento de medición de Klein Tools
Klein Tools
Klein Tools ET160 Manual de usuario
Klein Tools
Klein Tools CL110 Manual de usuario
Klein Tools
Klein Tools NCVT-1 Manual de usuario
Klein Tools
Klein Tools VDV512-110 Manual de usuario
Klein Tools
Klein Tools ET900 Manual de usuario
Klein Tools
Klein Tools Ranger TDR VDV501-090 Manual de usuario
Klein Tools
Klein Tools CL360 Manual de usuario
Klein Tools
Klein Tools ET910 Manual de usuario
Klein Tools
Klein Tools CL2200 Manual de usuario
Klein Tools
Klein Tools Coax Explorer 2 Manual de usuario
Klein Tools
Klein Tools RT390 Manual de usuario
Klein Tools
Klein Tools MM2000 Manual de usuario
Klein Tools
Klein Tools IR2000A Manual de usuario
Klein Tools
Klein Tools CL210 Manual de usuario
Klein Tools
Klein Tools 93MCLG Manual de usuario
Klein Tools
Klein Tools NCVT-1XTKIT Manual de usuario
Klein Tools
Klein Tools CL2200 Manual de usuario
Klein Tools
Klein Tools VDV Scout Pro 2 LT Manual de usuario
Klein Tools
Klein Tools PROBEplus Manual de usuario
Klein Tools
Klein Tools 935DAGL Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario