Kichler Lighting Almere Manual de usuario

Product images may vary slightly from actual product.

56” Almere

INSTRUCTION MANUAL

Model# 330130READ AND SAVE THESE INSTRUCTIONS

2 | KICHLER.COM

TABLE OF CONTENTS

ELECTRICAL CONNECTIONS……………………………………………12

INSTALLING THE WALL CONTROL…………………………………14

COMPLETING THE FAN INSTALLATION………………………15

OPERATING INSTRUCTIONS……………………………………………16

FCC INFORMATION……………………………………………………………17

TROUBLESHOOTING………………………………………………………18

SAFETY RULES……………………………………………………………………3

TOOLS REQUIRED………………………………………………………………5

PACKAGE CONTENTS…………………………………………………………5

MOUNTING OPTIONS…………………………………………………………6

ATTACHING THE FAN BLADES…………………………………………7

HANGING THE FAN……………………………………………………………8

INSTALLATION OF SAFETY SUPPORT……………………………11

fan support and may need to be replaced. Due to the

complexity of the installation of this fan, a qualified

licensed electrician is strongly recommended.

6. The outlet box and support structure must be

securely mounted and capable of reliably supporting

a minimum of 15.9 kg (35 pounds). Use only cULus

Listed outlet boxes marked “Acceptable for Fan

Support of 15.9 kg (35 lbs) or less”.

7. The fan must be mounted with a minimum of 2.1 m (7

feet) clearance from the trailing edge of the blades to

the floor.

8. WARNING: Do not operate reversing switch while

fan blades are in motion. Fan must be turned o and

blades stopped before reversing blade direction.

9. Avoid placing objects in the path of the blades.

10. WARNING: make sure the power is disconnected

before cleaning your fan.

56” Almere | 3

READ AND SAVE THESE INSTRUCTIONS

SAFETY RULES

WARNING: FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY TO THE BUILDING STRUCTURE / CEILING JOIST.

DON’T SECURE THIS FAN TO AN OUTLET BOX.

1. CAUTION – RISK OF SHOCK: Disconnect Power at

the main circuit breaker panel or main fusebox before

starting and during the installation.

2. WARNING: All wiring must be in accordance with the

National Electrical Code “ANSI/NFPA 70” and local

electrical codes. Electrical installation should be

performed by a qualified licensed electrician.

3. WARNING: To reduce the risk of electric shock, this

fan must be installed with a general-use, isolating wall

control/switch.

4. WARNING: Not suitable for use with solid-state speed

controls.

5. WARNING: To reduce the risk of fire, electric shock,

or personal injury, mount to outlet box marked

“acceptable for fan support of 15.9 kg (35 lbs.) or

less” and use mounting screws provided with the

outlet box. Most outlet boxes commonly used for

the support of light fixtures are not acceptable for

4 | KICHLER.COM

16. N.W. 7.82 KGS (17.24 LBS) / G.W. 8.75 KGS (19.29 LBS)11. To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

12. Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened

cloth will be suitable for most cleaning.

13. After making electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be

spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the

outlet box and the ungrounded conductor on the

other side of the outlet box.

14. Electrical diagrams are reference only. Light kits that

are not packed with the fan must be cULus Listed

and marked suitable for use with the model fan you

are installing. Switches must be cULus General Use

Switches. Refer to the Instructions packaged with the

light kits and switches for proper assembly.

15. All set screws must be checked, and retightened

where necessary, before installation.

SAFETY RULES

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADES DURING ASSEMBLY OR AFTER INSTALLATION.

DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

• Phillips Screwdriver

• Blade Screwdriver

• 11 mm Wrench

• Step Ladder

• Wire Cutters

Unpack your fan and check the contents . You should have the following items:

A. Ball/Downrod Assembly

B. Mounting Bracket

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Assembly

G. Blade (3)

H. Blade Holder

I J

56” Almere | 5

I. Wall Control Unit

Face plate (1); Wall control (1); Receiver(1);

Wire Connector (4+5);

Long screw (2);

J. Package hardware

1.) Safety cable hardware: Wood screw (1);

Spring washer (1); Flat washer (1)

2.) Mounting hardware: Wire Connector (3);

3.) Blade attachment hardware: Screw (12);

4.) Motor Assembly attachment hardware: Screw (3) x12

6 | KICHLER.COM

Fig. 1

Outlet box

Fig. 2

Fig. 3

Recessed

outlet box ceiling

mounting

plane

Provide strong

support

ANGLED CEILING

MAXIMUM 22° ANGLE

Fig. 4

Outlet box

MOUNTING OPTIONS

If there is not an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the full weight of the fan (up

to 15.9kg (35 pounds)). Do not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A minimum

clearance of 12" is suggested for optimal operation.

NOTE: You must use 12" or longer downrod for 22° slope

(max angle 22°). (Fig. 3)

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist Hanger”

for the support of the outlet box. Make sure the joist hanger you

purchase has been designed for use with ceiling fans. (Fig. 4)

56” Almere | 7

ATTACHING THE FAN BLADES

CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The

Electrical Supply Circuit To The Fan Before Installing Fan Blades.

Step 1. Align the four holes in a blade with four matching holes in the

blade holder. Thread blade attachment screws into the aligned holes,

and tighten screws to secure the blade to the blade holder. Repeat for

remaining blades. (Fig. 5)

Step 2. NOTE: Inside of the blade holder there are six tabs. Three of the

tabs have a post on top, and three of the tabs have a hole in the center.

NOTE: In the outer ring of the motor assembly there are six holes. Three

of the holes are smaller in size and three of the holes are larger in size.

Carefully insert the motor assembly into the blade holder, aligning the

smaller holes in the motor assembly with the posts on top of the tabs.

Pass the posts through the smaller holes, and seat the outer ring of the

motor assembly on top of all six tabs.

The larger holes in the motor assembly should align with the holes in

the tabs. Thread the three motor assembly attachment screws into the

larger holes in the motor assembly and into the holes in the tabs, and

tighten to secure the motor assembly to the blade holder. (Fig. 6)” Fig. 6

Fig. 5

Blade Holder

BladeAttachment

Screws

Blade

Tab With Hole

Blade Holder

Motor Assembly

Tab With Post

Motor Assembly

Attachment Screws

8 | KICHLER.COM

Fig. 7

Fig. 8

Fig. 9

Outlet Box

Ceiling Mounting

Bracket

Flat Washer

Screw

Set Screw

Hanger Ball

Cross Pin

Clevis Pin

Downrod

Hairpin

HANGING THE FAN

REMEMBER to turn o the power before you begin installation. This is necessary for

your safety and also the proper programming of the control system.

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching fan to outlet box (not included), ensure the outlet box is securely

fastened to at least two points to a structural ceiling member (a loose box will cause the

fan to wobble). Pass the 120 volt supply wires from the ceiling outlet box through the

center of the ceiling mounting bracket. Install mounting bracket to outlet box in ceiling

using the screws and washers included with the outlet box. (Fig. 7)

Step 2. Remove the hairpin and clevis pin from the downrod assembly, retain for later

use. Remove the hanger ball from the downrod assembly by loosening set screw,

removing the cross pin, and sliding ball o of the rod. (Fig. 8)

NOTE: Make sure to keep loosened hardware separate to avoid confusion during

installation.

Step 3. Loosen the two set screws on the motor coupling. (Fig. 9)

Set Screw

Motor Coupling

56” Almere | 9

Step 4. Carefully feed fan wires and safety cable up through the

downrod. Thread the downrod onto the motor coupling until the clevis

pin holes are aligned. Next, replace the clevis pin and hairpin, then tighten

both set screws. (Fig. 10)

Step 5. Slip the coupling cover, canopy hole cover and canopy onto the

downrod. Carefully reinstall the hanger ball onto the downrod. Make sure

the cross pin is in the correct position and the set screw is tight and the

wires are not twisted . ( Fig. 11)

CAUTION: Ensure all screws are tight before moving to the next step.

HANGING THE FAN (continued)

Motor Coupling

Downrod

Cross Pin

Set Screw

Hairpin Clevis Pin

Set Screw

Fig. 10

Fig.11

Canopy

Hanger Ball

Canopy Hole Cover

Coupling Cover

Downrod

10 | KICHLER.COM

Step 6. Now lift the motor assembly into position and place the hanger

ball into the mounting bracket. Rotate until the “Check Tab” has dropped

into the “Registration Slot “ and seats firmly. ( Fig. 12) The entire motor

body should not rotate if this is done correctly.

WARNING: Failure to properly seat the “Check Tab” can damage the

ceiling fan during operation.

HANGING THE FAN (continued)

Fig. 12

Check Tab

Registration Slot

Mounting Bracket

Hanger Ball

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Admirador de Kichler Lighting

Kichler Lighting

Kichler Lighting Ample Manual de usuario

Kichler Lighting

Kichler Lighting Renew Select Patio Manual de usuario

Kichler Lighting

Kichler Lighting SPYRA Manual de usuario

Kichler Lighting

Kichler Lighting Monarch II Select Manual de usuario

Kichler Lighting

Kichler Lighting 52" RENEW DESIGNER Manual de usuario

Kichler Lighting

Kichler Lighting 300044 Manual de usuario

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Manual de usuario

Kichler Lighting

Kichler Lighting VASSAR Manual de usuario

Kichler Lighting

Kichler Lighting Szeplo 370060 Manual de usuario

Kichler Lighting

Kichler Lighting Golden Iridescence Manual de usuario

Kichler Lighting

Kichler Lighting Compass 300322 Manual de usuario

Kichler Lighting

Kichler Lighting BASICS PRO SELECT 330017MWH Manual de usuario

Kichler Lighting

Kichler Lighting Highland Manor Manual de usuario

Kichler Lighting

Kichler Lighting Canfield Manual de usuario

Kichler Lighting

Kichler Lighting Select Sutter Place Manual de usuario

Kichler Lighting

Kichler Lighting Select Sutter Place Manual de usuario

Kichler Lighting

Kichler Lighting 52" Basics Pro Manual de usuario

Kichler Lighting

Kichler Lighting Selectlight fixture Manual de usuario

Kichler Lighting

Kichler Lighting True Manual de usuario

Kichler Lighting

Kichler Lighting Terra Select Manual de usuario

Kichler Lighting

Kichler Lighting 300395 Manual de usuario

Kichler Lighting

Kichler Lighting Logan Manual de usuario

Kichler Lighting

Kichler Lighting Lehr Decor 80" Manual de usuario

Kichler Lighting

Kichler Lighting 330015WH Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje