Kichler Lighting 52" RENEW DESIGNER Manual de usuario

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

52" RENEWTM DESIGNER

UL Model #330163

52" RenewTM Designer | 3

SAFETY RULES

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

MOUNTING OPTIONS

HANGING THE FAN

INSTALLATION OF SAFETY SUPPORT

ELECTRICAL CONNECTIONS

FINISHING THE MOTOR INSTALLATION

ATTACHING THE FAN BLADES

INSTALLING THE LED LIGHT KIT

OPERATING INSTRUCTIONS

TROUBLESHOOTING

TABLE OF CONTENTS

Read all instructions BEFORE assembly and USE of product

KEEP INSTRUCTIONS FOR FUTURE USE

| KICHLER.COM

SAFETY RULES

1. CAUTION -RISK OF SHOCK-

Disconnect Power at the main circuit breaker panel or main

fusebox before starting and during the installation.

2. WARNING:Thisfixture is intendedforinstallationin accordance

with the National Electrical Code (NEC) and all local code

specifications. If you are not familiar with code requirements,

installation by a certified electrician is recommended.

3. WARNING: Suitable for use with solid-state speed controls.

4. WARNING: To reduce the risk of personal injury, use only the

two steel screws (and lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet boxes commonly

used for the support of lighting fixtures are not acceptable for

fan support and may need to be replaced, consult a qualified

electrician if in doubt.

5. WARNING: To reduce the risk of fire, electric shock or personal

injury, mount fan to outlet box marked “acceptable for fan

support”.

6. The outlet box and support structure must be securely mounted

and capable of reliably supporting a minimum of 50 pounds. Use

only CUL Listed outlet boxes marked “FOR FAN SUPPORT”.

7. The fan must be mounted with a minimum of 7 feet clearance

from the trailing edge of the blades to the floor.

8. Do not operate reversing switch while fan blades are in motion.

Fan must be turned o and blades stopped before reversing

blade direction.

9. Avoid placing objects in the path of the blades.

10. To avoid personal injury or damage to the fan and other items,

be cautious when working around or cleaning the fan.

11. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be suitable

for most cleaning.

12. After marking electrical connections, spliced conductors should

be turned upward and pushed carefully up into outlet box. The

wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet

box.

13. Electrical diagrams are reference only. Light Kits that are not

packed with the fan must be CUL Listed and marked suitable for

use with the model fan you are installing. Switches must be CUL

General Use Switches. Refer to the Instructions packaged with

the light kits and switches for proper assembly.

14. WARNING: To reduce the risk of personal injury, do not bend

the blade brackets (also reered to as flanges) during assembly

or after installation. Do not insert objects in the path of blades.

52" RenewTM Designer | 5

TOOLS REQUIRED

PACKAGE CONTENTS

• Philips screw driver

• Blade screw driver

• 11mm wrench

• Step ladder

• Wire cutters

Unpack your fan and check the contents. You should have the following items:

A. Fan blades (5)

B. Ceiling mounting bracket

C. Canopy decoration ring

D. Canopy

E. Canopy Cover

F. Ball/downrod assembly

G. Coupler cover

H. Fan motor assembly

I. 17W LED Light Kit

J. Blade brackets with pre-installed

mounting screws (5)

K. Package hardware:

1) Safety cable hardware:

screw (1), flat washer (1)

2) Gasket

3) Pull chains and fobs (1)

4) Balancing Kit

5) Blade attachment hardware:

screws (15), washers (15)

L. Glass shade

M. Remote package

1) Receiver

2) Wall transmitter

| KICHLER.COM

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting plate

Outlet box

ANGLED CEILING

MAXIMUM 22°

ANGLE

MOUNTING OPTIONS

If there is not an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the full weight of the fan (up

to 50 lbs). Do not use plastic outlet boxes.

Figures 1, 2, and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A minimum

clearance of 12” is suggested for optimal operation.

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist Hanger”

for the support of the outlet box. Make sure the joist hanger you

purchase has been designed for use with ceiling fans. (Fig. 4)

Fig. 2

Fig. 1

Fig. 3

Fig. 4

52" RenewTM Designer | 7

HANGING THE FAN

REMEMBER to turn o the power before you begin.

To properly install your ceiling fan, follow the steps below.

NOTE: This ceiling fan is supplied with two types of hanging

assemblies; the standard ceiling installation using the downrod with

ball and socket mounting and the “close-to-ceiling” installation. The

“close-to-ceiling” installation is recommended in rooms with less

than 8-feet ceilings or in areas where additional space is desired from

the floor to the fan blades.

CUL Listed

lectrical box

Ceiling

mounting

bracket

Mounting screws

(supplied with electrical box

)

Washer

120V wires

Fig. 5

| KICHLER.COM

HANGING THE FAN

Standard Ceiling Installation

Step 1. Pass the 120-volt supply wires through the center hole in the

ceiling hanger bracket as shown in Fig. 5.

Step 2. Secure the hanger bracket to the ceiling outlet box with the

screws and washers provided with your outlet box.

Step 3. Remove the hitch pin, lock pin and set screws from the top of the

motor assembly.

Step 4. Route wires exiting from the top of the fan motor through the

coupler cover, canopy cover, canopy, decoration ring and then through

the ball/downrod. (Fig. 6)

Step 5. Align the holes at the bottom of the downrod with the holes

in the collar on top of the motor housing (Fig. 6). Carefully insert the

hitch pin through the holes in the collar and downrod. Be careful not

to jam the pin against the wiring inside the downrod. Insert the locking

pin through the hole near the end of the hitch pin until it snaps into its

locked position, as noted in the circle inset of Fig. 6.

Step 6. Tighten two set screws on top of the fan motor firmly. (Fig. 6)

Step 7. Place downrod ball into the hanger bracket socket. (Fig 7)

Fig. 6

Fig. 7

Registration slotCheck tab

Locking pin

Set screws

Hitch pin

Ceiling canopy

Decoration ring

Coupler cover

Downrod

Cross pinHanger ball

52" RenewTM Designer | 9

Fig. 7

HANGING THE FAN

Close-to-Ceiling Installation

Step 1. Pass the 120-volt supply wires through the center hole in the

ceiling hanger bracket as shown in Fig. 8.

Step 2. Secure the hanger bracket to the ceiling outlet box with the

screws and washers provided with your outlet box.

Step 3. Remove three of the six screws and lock washers (every

other one) from the collar of top motor (Fig. 9)

Step 4. Place the ceiling canopy with decoration ring and the

gasket over the collar at the top of the motor. Align the mounting

holes with the holes in the motor and fasten using the screws and

lock washers provided. (Fig. 9)

Step 5. Tighten the mounting screws securely. (Fig. 9)

WARNING: Failure to completely tighten the three screws in step 5

could result in fan loosening and possibly falling.

Step 6. Hang the fan on the hook of the hanger bracket. Be certain

that the canopy is fully locked into hook as shown in Fig. 10. This will

allow you to make the electrical connections.

Ceiling mountin

bracket

Canopy

Hook

Fig. 8

Fig. 9

Screws and Lock

washers(3 of 6 places)

Canopy

Gasket

Collar

Decoration ring

| KICHLER.COM

INSTALLATION OF SAFETY SUPPORT

(Required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan

from falling, please install it as follows.

Step 1. Attach the provided wood screw and washers to the ceiling

joist next to the mounting bracket but do not tighten. (Fig. 10)

Step 2. Adjust the length of the safety cable to reach the screw and

washers by pulling the extra cable through the cable clamp until the

overall length is correct, put the end of the cable back through the

cable clamp, forming a loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of the safety cable over

the wood screw securely.

NOTE: Although the safety support cable is required for Canadian

installations only. It’s a good idea to make the attachment with

any installation.

Fig. 10

Hanger bracket

Safety cable

Attach safety cable

to ceiling joist with

screw

WARNING: To avoid possible electrical shock, be sure you have

turned o the power at the main circuit panel.

Follow the steps below to connect the fan to your household wiring.

Use the wire connecting nuts supplied with your fan. Secure the

connector with electrical tape. Make sure there are no loose wire

strands or connections.

Step 1. Insert the receiver into the ceiling mounting bracket with

the flat side of the receiver facing the ceiling. (Fig. 11) For best

performance, make sure the Black Antenna, on the end of the

receiver, remains extended and not tangled with any of the electrical

wires.

ELECTRIC CONNECTIONS

Ceiling mounting

bracket

Receiver

Fig. 11

52" RenewTM Designer | 11

Step 2. Motor to Receiver Electrical Connections: (Fig. 14) Connect the

black wire from the fan to the black wire marked “TO MOTOR L” on the

receiver. Connect the white wire from the fan to the white wire marked

“TO MOTOR N” on the receiver. Connect the blue wire from the fan to

the blue wire marked “FOR LIGHT” on the receiver. Secure all the wire

connections with the plastic wire nuts provided.

Step 3. (Fig. 14) Receiver to House Supply Wires Electrical Connections:

Connect the black (hot) wire from the ceiling to the black wire marked

“AC in L” from the receiver. Connect the white (neutral) wire from the

ceiling to the white wire marked “AC in N” from the receiver. Secure the

wire connections with the plastic wire nuts provided.

Step 4. (Fig. 14) If your outlet box has a ground wire (green or bare

copper) connect it to the fan ground wires; otherwise connect the

hanging bracket ground wire to the mounting bracket. Secure the wire

connection with a plastic nut (provided). After connecting the wires,

spread them apart so that the green and white wires are on one side

of the outlet box and black and blue wires are on the other side.

Carefully tuck the wire connections up into the outlet box.

Fig. 12

ELECTRIC CONNECTIONS

Outlet box

in the ceiling

Green (or bare)

Green

White

Black

Blue

Black

Receiver

Tabla de contenidos

Otros manuales de Admirador de Kichler Lighting

Kichler Lighting

Kichler Lighting Starkk 330180MWH Manual de usuario

Kichler Lighting

Kichler Lighting 52" Basics Pro Manual de usuario

Kichler Lighting

Kichler Lighting Vinea 52 Manual de usuario

Kichler Lighting

Kichler Lighting KLF-SOLA-34-WHT-BN Manual de usuario

Kichler Lighting

Kichler Lighting Wilton Manual de usuario

Kichler Lighting

Kichler Lighting 330013 Manual de usuario

Kichler Lighting

Kichler Lighting sterling manor select Manual de usuario

Kichler Lighting

Kichler Lighting Industrial Fan Manual de usuario

Kichler Lighting

Kichler Lighting 330163 Manual de usuario

Kichler Lighting

Kichler Lighting Maeve LED 52 Manual de usuario

Kichler Lighting

Kichler Lighting Lija 330140NI Manual de usuario

Kichler Lighting

Kichler Lighting Cortez Manual de usuario

Kichler Lighting

Kichler Lighting 35155 Manual de usuario

Kichler Lighting

Kichler Lighting Sterling Manor Manual de usuario

Kichler Lighting

Kichler Lighting Meredith Manual de usuario

Kichler Lighting

Kichler Lighting Crescent 300325 Manual de usuario

Kichler Lighting

Kichler Lighting Starkk Manual de usuario

Kichler Lighting

Kichler Lighting LYNDON Manual de usuario

Kichler Lighting

Kichler Lighting Terna 300230 Manual de usuario

Kichler Lighting

Kichler Lighting ERIS 337060 Manual de usuario

Kichler Lighting

Kichler Lighting Olympia Manual de usuario

Kichler Lighting

Kichler Lighting FRYST Manual de usuario

Kichler Lighting

Kichler Lighting Imari 65 Manual de usuario

Kichler Lighting

Kichler Lighting 35152 Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje