Kargo Master 4A81L Manual
Instruction Guide
4A81L
Kargo Master
Rancho Cordova, CA 95742
800-343-7486
CustomerService@KargoMaster.com
DATE: ______________
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 1
Instructions –4A81L
*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
INSTALLING, AND USING THIS PRODUCT*
Warning
Always check for wires, fuel tanks and lines, brake lines and other important vehicle
functionality items prior to drilling and installing all products.
Tools Needed
9/16” Socket and Wrench
1/2” Socket and Wrench
Table of Contents
Parts List ................................................................................................................................... 2
Assembly Hardware .............................................................................................................. 3-4
Step 1 –Remove Ladder Stops .............................................................................................. 5
Step 2 –Mount Side Tube ..................................................................................................... 6
Step 3 –Mount Clamp Tube ............................................................................................... 7-8
Step 4 –Mount Handle .......................................................................................................... 9
Step 5 –Mount Latch Assembly ............................................................................................ 9
Step 6 –Mount Ladder Hook .............................................................................................. 10
Step 7 –Install Extra Pad ..................................................................................................... 10
Before You Begin
•Read all instructions.
•DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF.
•This kit is the Driver Side add on ONLY.
•BE SURE TO ADJUST LADDER CLAMPS ACCORDINGLY TO FIRMLY SECURE LADDER TO RACK.
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 2
Instructions –4A81L
Parts
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 3
Instructions –4A81L
Assembly Hardware (18-4A81L)
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 4
Instructions –4A81L
Assembly Hardware (18-4A81L) Continued
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 5
Instructions –4A81L
Step 1 –Remove Ladder Stops
•If havent already done so, remove ladder stops from opposite end of both bows where the
clamp and lock is installed.
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 6
Instructions –4A81L
Step 2 –Mount Side Tube
•Place a generous amount of sealant
into the tube connection.
•Place side tube on top of installed
bows.
•Have the bend towards the front of
the vehicle as shown.
•Mount rotation bar plate to the rear
of the tube as shown.
•Leave one square slot open at the rear.
•Bolt together using 5/16” x 2” carriage bolt, a 5/16” flat washer and a 5/16” nyloc.
•Snug Tighten, but allow movement.
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 7
Instructions –4A81L
Step 3 –Mount Clamp Tube
•Place clamp and lock L bracket on top of installed bows. Do not install hardware right now.
•Insert plastic bushings into the clamp and lock L bracket and the rotation bar plate installed in
Step 2, with flanges as shown so they cannot come out at a later time. If bushings are not
placed in correct orientation, they can fall out.
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 8
Instructions –4A81L
•Insert clamp tube into both plastic bushings.
•Adjust clamp on clamp tube to fit firmly against your ladder.
•Bolt clamp and lock L bracket to bows using 3/8”x 1”carriage bolt, 3/8”flat washer and a
3/8”nyloc as shown.
•TIGHTEN
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 9
Instructions –4A81L
Step 4 –Mount Handle
•Bolt handle to clamp tube using a 5/16” x 2-3/4” hex head, two 5/16” flat washers, 5/16”
nylon washer and 5/16” a nyloc. The nylon washer goes in between the clamp tube and
handle.
•TIGHTEN
Step 5 –Mount Latch Assembly
•Bolt latch to the rear of the mount tube that was installed in Step 5 using 5/16” x 2” carriage
bolt, 5/16” curved washer and a 5/16” nyloc.
•TIGHTEN
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Kargo Master
Kargo Master
Kargo Master 40816 Manual
Kargo Master
Kargo Master 4089P Manual
Kargo Master
Kargo Master 40669SH Manual
Kargo Master
Kargo Master 40053 Manual
Kargo Master
Kargo Master 4A98L-Rev 1 Manual de usuario
Kargo Master
Kargo Master PRO-III Manual de usuario
Kargo Master
Kargo Master Congo Pro Kit Manual de usuario
Kargo Master
Kargo Master 48152 Manual de usuario
Kargo Master
Kargo Master 40110 Manual de usuario
Kargo Master
Kargo Master 80070 Manual
Kargo Master
Kargo Master 30070 Manual de usuario
Kargo Master
Kargo Master 80070 Hoja de datos
Kargo Master
Kargo Master 40150 Manual
Kargo Master
Kargo Master 406GMF-P Manual
Kargo Master
Kargo Master 4081M Manual de usuario
Kargo Master
Kargo Master 409CD Manual de usuario
Kargo Master
Kargo Master 4A943 Manual de usuario
Kargo Master
Kargo Master 40201 Manual de usuario
Kargo Master
Kargo Master 40933 Manual
Kargo Master
Kargo Master 4A84L Manual
