Kargo Master 406GMF-P Manual
Kargo Master
Rancho Cordova, CA 95742
800-343-7486
CustomerService@KargoMaster.com
20210319R1 DATE: ________________
Instruction Guide
406GMF-P
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 1
*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING, INSTALLING,
AND USING THIS PRODUCT. *
Warning
Always check for wires, fuel tanks and lines, brake lines and other important vehicle
functionality items prior to drilling and installing all products.
Tools Needed
7/16” Socket and Wrench
7/16” Box Wrench
10MM Socket and Wrench
10MM Box Wrench
Table of Contents
Before You Begin............................................................................................................................................... 1
Parts .................................................................................................................................................................. 2
Hardware (18-406GMF-P)................................................................................................................................. 3
Hardware (18-40600)........................................................................................................................................ 3
Step 1 –Install Floor Mounts............................................................................................................................ 4
Step 2 –Install Upper Corner Mounts .............................................................................................................. 5
Step 3 –Attach Upper Mount to Corner Mounts............................................................................................. 6
Step 4 –Join Partition Panels............................................................................................................................ 7
Step 5 –Install Partition.................................................................................................................................... 8
Before You Begin
Read all instructions prior to assembling or installing any Kargo Master product.
Always locate your installation locations prior to performing any work.
ENSURE SAFETY WHILE INSTALLING INTO VEHICLE.
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 2
Parts
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 3
Hardware (18-406GMF-P)
Hardware (18-40600)
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 4
DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF
Step 1 –Install Floor Mounts
Behind both seats, locate the D-Rings in the floor.
Remove both D-Rings.
Align the floor mounts with the
previously removed D-Rings. Orient
the vertical flanges on floor mounts
towards rear of the van.
Loosely install the floor mounts using
the previously removed D-Rings as
shown.
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 5
Step 2 –Install Upper Corner Mounts
Along the roof of the van, locate the mount
locations behind both seats. These are above the
slider door.
Evaluate the mounting locations and determine if a threaded emboss is present.
Note: In some vans, a M6 threaded emboss will be attached (see picture above). The others will have two
through holes.
Be sure to use the correct upper corner mount. When the mount is attached properly, the flange should
be towards the front of the vehicle and parallel to the floor. The slots in the upper corner mount will
attach to the partition assembly.
Through the rear most hole of the upper corner mount, attach in place using a M6 x 22mm hex head bolt,
two 1/4” flat washers and a 1/4” lock nut in the orientation shown.
Driver Side Shown Here
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 6
If there is no threaded emboss
on the forward most hole
location, install corner mount
using a M6 x 22mm hex head
bolt, two 1/4” flat washers and
1/4” lock nut in the orientation
shown.
Snug tighten, but allow
movement.
If a threaded emboss is present,
attach through the front most
hole location, install corner
mount using a M6 x 22mm hex
head bolt, 1/4” lock washer and
1/4” flat washer, as shown.
Snug tighten, but allow
movement.
Repeat this step on opposite
side of vehicle for opposing
corner mount.
Tighten corner mount
hardware.
Step 3 –Attach Upper Mount to Corner Mounts
Using two 1/4” x 5/8” flanged hex
head bolts and two 1/4” flanged lock
nuts, LOOSELY bolt upper mount to
a corner mount. Be sure to orient
the upper mount with the flange on
the front of vehicle and flange
downward. DO NOT tighten!
Driver Side Shown Here
Driver Side Shown Here
Driver Side Shown Here
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 7
Using two 1/4” x 5/8” flanged hex head bolts and two 1/4” flanged lock nuts, LOOSELY bolt upper mount
to opposing corner mount. DO NOT tighten!
Step 4 –Join Partition Panels
Using four 1/4” x 5/8”flanged hex head bolts and 1/4” flanged lock nuts, attach driver-side partition panel
to passenger-side partition panel. Be sure flanges are facing the same direction.
Snug tighten but allow for movement.
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 8
Attach rubber edge trimming to outer edges of partition panels.
Repeat for opposite side.
Step 5 –Install Partition
Position partition in vehicle. Flanges on partition are towards rear of vehicle.
Using six 1/4” x 5/8” flanged hex head bolts and 1/4” flanged lock nuts, LOOSELY bolt partition to upper
mount.
Snug tighten but allow for movement.
Instructions –406GMF-P
For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 9
Using four 1/4” x 1/2” hex head bolts, 1/4” lock washers, 1/4” flat washers, bolt partition to nuts pressed
in floor mounts.
Snug tighten but allow for movement.
Re-install previously removed D-rings.
GO BACK AND TIGHTEN ALL HARDWARE.
INSTALLATION AND ASSEMBLY ARE COMPLETE.
Shown from below for clarity.
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Kargo Master
Kargo Master
Kargo Master 4081P Manual de usuario
Kargo Master
Kargo Master 409CD Manual de usuario
Kargo Master
Kargo Master 40933 Manual
Kargo Master
Kargo Master KILIMANJARO Manual de usuario
Kargo Master
Kargo Master PRO-II KS Manual de usuario
Kargo Master
Kargo Master 4095L Manual de usuario
Kargo Master
Kargo Master 48152 Manual de usuario
Kargo Master
Kargo Master 48132 Manual de usuario
Kargo Master
Kargo Master 40201 Manual de usuario
Kargo Master
Kargo Master 4A824 Manual
Kargo Master
Kargo Master 40020 Manual de usuario
Kargo Master
Kargo Master 40890 Manual de usuario
Kargo Master
Kargo Master 4A98L-Rev 1 Manual de usuario
Kargo Master
Kargo Master 4A96M Manual de usuario
Kargo Master
Kargo Master 40669SH Manual
Kargo Master
Kargo Master 406GM Manual
Kargo Master
Kargo Master 4A82T Manual de usuario
Kargo Master
Kargo Master PRO-IV Manual de usuario
Kargo Master
Kargo Master 80070 Manual
Kargo Master
Kargo Master 4090L Manual
