ICP DAS USA M-7067 Manual de usuario

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7067

7 Channel Form A Relay Output Digital Input

Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7067_m_7067d.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7067 device is a network data acquisition and control module that

support Modbus RTU. They can be remotely controlled using a set of

commands called DCON protocol. With the Modbus RTU protocol, it can

easily communicate with most popular SCADA/ HMI software and PLCs.

2. Terminal Assignment

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

4. Default Settings

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

。Checksum disabled

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the digital input and output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format

to search module. The default settings for the module can be found in Section 3.

Click OK after selecting the COM port setting.

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA ET-87P2 Manual de usuario

ICP DAS USA

ICP DAS USA tGW-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA ET-7000 series Manual de usuario

ICP DAS USA

ICP DAS USA M-7053D Manual de usuario

ICP DAS USA

ICP DAS USA M-7016 Manual de usuario

ICP DAS USA

ICP DAS USA I-7045D Manual de usuario

ICP DAS USA

ICP DAS USA MDC-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7064 Manual de usuario

ICP DAS USA

ICP DAS USA MDC-714i Manual de usuario

ICP DAS USA

ICP DAS USA I-7080 Manual de usuario

ICP DAS USA

ICP DAS USA I-7060D Manual de usuario

ICP DAS USA

ICP DAS USA GTP-230 Manual de usuario

ICP DAS USA

ICP DAS USA I-2533 Manual de usuario

ICP DAS USA

ICP DAS USA GTM-204M-4G Manual de usuario

ICP DAS USA

ICP DAS USA M-7041 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2012H Manual de usuario

ICP DAS USA

ICP DAS USA ET-7218Z Manual de usuario

ICP DAS USA

ICP DAS USA LinPAC-51 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7016 Manual de usuario

ICP DAS USA

ICP DAS USA tM-P3R3 Manual de usuario

ICP DAS USA

ICP DAS USA EIP-2000 Series Guía de instalación

ICP DAS USA

ICP DAS USA HRT-711 Manual de usuario

ICP DAS USA

ICP DAS USA tM Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7065 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario