ICP DAS USA ECAT-2012H Manual de usuario

Technical support: servic[email protected] P1

ECAT-2012H Quick Start

v1.0, Oct. 2019

What’s in the box?

1 Connecting the Power and Host PC

Switch on module and connect it to an EtherCAT network

NOTE: Attaching an ESC directly to an office network will result in network

flooding, since the ESC will reflect any frame – especially broadcast frames –

back into the network (broadcast storm).

Verify that LEDs indicator

The package includes the following items:

ECAT-2012H Module x 1

Quick Start x1 (This Document)

1) Connect the Host device to the IN

port on ECAT-2012H module.

2) Connect the PWR+ pin to positive

terminal on a +10 - +30 VDC power

supply, and connect the GND- pin to

the negative terminal.

Red, OK

Green, OK

OUT

+Vs

GND

F.G.

Technical support: servic[email protected] P2

2 Search Modules

ESI file

The latest ESI file (ICPDAS ECAT-2012.xml) can be

downloaded from ICP DAS website at

http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethercat/slave/ecat-2000/software/

Install the ESI file

Copy the “ICPDAS ECAT-2012.xml” file to the Master Tools installation folder, as

indicated in the table below.

Software

Default Path

Beckhoff EtherCAT Configuration

C:\EtherCAT Configurator\EtherCAT

Beckhoff TwinCAT 3.X

C:\TwinCAT\3.x\Config\Io\EtherCAT

Beckhoff TwinCAT 2.X

C:\TwinCAT\Io\EtherCAT

Run the EtherCAT Master software (Beckhoff TwinCAT 2.X)

Switch on power and execute the TwinCAT System Manager (Config mode)

1. I/O Devices Right click 

Scan Devices…

2. Click “OK” button

3. Choose the correct network

device which is connected to

ECAT-2012H and click “OK”

button

Technical support: servic[email protected] P3

(Default Settings)

3 Wiring to the Connector

Wiring Tip

Connecting the wire

Removing the wire

Wire Diagrams

Voltage Input (Differential) Voltage Input (Single-ended) Current Input

4. Click “OK” to start scanning

Click “OK” to activate the free run

mode for TwinCAT system

manager

5. In the left-hand window,

ECAT-2012His now shown in the

TwinCAT system Manager

Use the blade of a

flat-head screwdriver to

push the wire clamp, then

hold until step 2 complete.



Insert the

wire



Use the blade of a

flat-head screwdriver to

push the wire clamp, then

hold until step 2 complete.



Remove the

wire



mV/V

Vx+

Vx-

mV/V V

Vx+

AGND

Vx+

Vx-

Technical support: servic[email protected] P4

Wiring the AI0 (Analog Input type default is Differential input)

Verifying the AI Functionality

Related Information

Connect the V0- (Pin01) to

signal positive (-)

Connect the V0+ (Pin02) to

signal positive (+)





(+)

(-)

Stable Signal Source (e.g., Dry Battery)

EtherCAT Series Product Page:

http://www.icpdas.com/root/product/solutions/industrial_communication/fieldb

us/ethercat/ethercat_selection_guide.html

Documentation & Software:

http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethercat/slave/ecat-2000/

1. Click “AI0”in the left-hand window.

2. In the right-hand window, check the

voltage value in the “Value” item.

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA tM-P3R3 Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2510 Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7019Z Manual de usuario

ICP DAS USA

ICP DAS USA ET-7083 Manual de usuario

ICP DAS USA

ICP DAS USA SG-3784M Manual de usuario

ICP DAS USA

ICP DAS USA WF-2026 Manual de usuario

ICP DAS USA

ICP DAS USA LP-8 21 Series Instrucciones generales

ICP DAS USA

ICP DAS USA M-7002 Manual de usuario

ICP DAS USA

ICP DAS USA DS-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7017R Manual de usuario

ICP DAS USA

ICP DAS USA M-7065 Manual de usuario

ICP DAS USA

ICP DAS USA ISN-101 Manual de usuario

ICP DAS USA

ICP DAS USA DL-10 Manual de usuario

ICP DAS USA

ICP DAS USA tPET-P6 Manual de usuario

ICP DAS USA

ICP DAS USA PET-AR400 Manual de usuario

ICP DAS USA

ICP DAS USA tET-P2A2 Manual de usuario

ICP DAS USA

ICP DAS USA PDS-5000 Series Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2011H Manual de usuario

ICP DAS USA

ICP DAS USA PISO-CPM100U-D/T Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2000 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7055D Manual de usuario

ICP DAS USA

ICP DAS USA I-7083 Manual de usuario

ICP DAS USA

ICP DAS USA M-7016 Manual de usuario

ICP DAS USA

ICP DAS USA DS-2200 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario