HP Integrity rx1600 Manual de usuario

February 2004

Printed in the U.S.A.

Smart Array (A9890A) Cable Routing

The purpose of this document is to provide cable routing information when a Smart Array PCI-X RAID card (A9890A)

is used to drive the embedded hard disk drives. The existing SCSI cable connected to the Channel A connector on the

system board is relocated to the Channel A connector on the Smart Array PCI-X card installed in slot 1 (full-length slot)

of the PCI cage.

The SCSI cable is routed from the PCI cage under the power supply bracket and over the IDE cable, if installed, avoiding

blocking the airflow of the chassis fans.

Refer to the hp integrity rx1600 Operation and Maintenance Guide for detailed instructions on powering down the

server, extending the server from a rack, and removing and replacing covers and components.

1. Disconnect the SCSI cable from the Channel A connector on the system board by pulling on the cable release strap.

See figure 1.

Figure 1. SCSI Channel A Connector on System Board

2. Remove the PCI cage from the server.

3. Remove any accessory card installed in PCI slot 2 (half-length slot).

4. Install the Smart Array PCI-X RAID card (A9890A) in PCI slot 1 (full-length slot).

5. Orient the PCI cage with the installed PCI-X RAID card component-side-up allowing routing of the SCSI cable.

See figure 2.

Figure 2. Cable Routing on Smart Array Card and PCI Cage

NOTE If an optional management processor card is installed in the server, follow the

instructions provided in the hp integrity rx1600 Operation and Maintenance Guide to

remove the card, allowing access to the Channel A connector. Reinstall the card after the

SCSI cable has been disconnected.

Channel A

connector

Around heatsink

Exit parallel to

connector

Channel A1

Under slot 2 connector

6. Attach the SCSI Channel A connector (previously removed from the system board connector) to the A1 Channel of

the PCI-X RAID card.

7. Route the SCSI cable around the heatsink on the PCI-X RAID card and under the edge of the PCI slot 2 connector.

See figure 2.

8. Continue routing the cable parallel to the connector edge of the PCI cage.

9. Reinstall any accessory card previously removed from PCI slot 2.

10. Install the PCI cage into the server chassis.

11. Route the SCSI cable under the power supply bracket as shown in figure 3.

Figure 3. Route Cable under Power Supply Bracket

12. Route the SCSI cable through the access slot of the fan assembly to the connector on the SCSI backplane.

See figure 4.

Figure 4. Cable Routing at SCSI Cage

13. Complete the installation by following the instructions provided in the hp integrity rx1600 Operation and

Maintenance Guide for closing up the server, installing in a rack, and powering-up. To enable RAID refer to the

A9890A documentation.

NOTE The SCSI cable should be routed over the IDE cable if the IDE cable is present.

CAUTION Do not block the airflow of the chassis fans. Reduced airflow may cause overheating.

Power Supply

Bracket

Route over IDE

cable (if present)

Do not block fans

Otros manuales para Integrity rx1600

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de HP

HP MCS G2 Guía de instalación

HP M8201R Manual de usuario

HP 98625A Manual de usuario

HP StorageWorks FC1142SR Manual de usuario

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manual de usuario

HP MicroServe Manual de usuario

HP Smart Array P400 Instrucciones de uso

HP Rp5700 - Point of Sale System Instrucciones de instalación

HP A1250 Series Instrucciones de montaje

HP 64767 Manual de usuario

HP Xw6600 - Workstation - 2 GB RAM Manual de usuario

HP 381513-B21 - Smart Array P800 Controller... Manual de usuario

HP 3000 III Series Manual de usuario

HP P Class 450/500/550/600/650/700/750 Manual

HP Z400 - Workstation Manual de usuario

HP 64746 Manual de usuario

HP Xw4600 - Workstation - 2 GB RAM Manual de usuario

HP A58 0AF Series Instrucciones de montaje

HP Model 744 - VME Workstation Manual de usuario

HP D7171A - NetServer - LPr Manual de usuario

HP P Class 450/500/550/600/650/700/750 Manual

HP 6600 FIP-20 Flex Instrucciones de montaje

HP ML570 - ProLiant - G2 Manual de usuario

HP OmniBook 3100 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario