HP Vectra VE4 Manual de usuario
Smart 16/4 PCI Token-Ring
Installation Guide
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent
of Hewlett-Packard Company.
Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft
Corporation.
MMXTM is a trademark of Intel Corporation.
Pentium® is a registered trademark of Intel Corporation.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France
1 Connecting to a Netware 3.12 Server
Windows for Workgroups
1 Connecting to a Netware 3.12 Server
Windows for
Workgroups
Requirements
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
• Madge Smart 16/4 PCI TR adapter and drivers diskettes ver 4.4.
• Driver Name: Size: 59KB Date: 5/22/95
• Novell Netware 3.12 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
• Netware client for DOS and MS-Windows.
Device Configuration
• Interrupt 9 (2)
• I/O Address FCC0-h
Procedure
1With the HP Vectra turned off install the Madge Smart16/4 PCI TR
adapter card into a PCI slot.
2Power on the machine and boot to a DOS prompt.
3Insert Netware Client for DOS and Windows Disk 1 and execute
“A:\INSTALL.”
4Change the settings to match the following and then option 6 to continue
the installation.
• C:\NWCLIENT
•YES
•YES
• C:\WINDOWS
•No
• Madge Smart 16/4 PCI Ringnode
5Insert the corresponding diskettes to finish the file transfer, and then
reboot the machine.
1 Connecting to a Netware 3.12 Server
Windows for Workgroups
6After windows loads, open the “NETWORK” folder, and double-click the
“NETWORK SETUP” icon.
7Select “Networks” and verify that “Novell Netware (Workstation Shell 4.0
and above)” is optioned under “Install Windows support for the following
network only.”
8Click on “OK” twice, and the installation is complete.
1 Connecting to a Netware 3.12 Server
Windows 95 SR2
Windows 95 SR2 Requirements
• HP Vectra with Windows 95 SR2 installed.
• Madge Smart16/4 PCI TR adapter and drivers diskettes ver 4.4.
• Driver Name: Windows 95 Default
• Novell Netware server that supports Net BEUI, NWLink IPX/SPX, and
NWLink NetBIOS transfer protocols.
Device Configuration
• Interrupt 9 (2)
• I/O Address FCC0-h
Procedure
1Upon booting, Windows 95 will automatically recognize the adapter. Click
on “Next.”
2When prompted, click on “Other Locations.”
3Insert drivers disk 2 of 2, set the path to “A:\WIN95\RPL\” and click “OK.”
(If you have an HP preloaded HDD, set the path to
“C:\LANDRV\MADGE\DISK2\ WIN95\RPL\”)
4Verify that “Madge Smart 16/4 PCI Ringnode (BM) 2” is listed and click on
“Finish.”
5Click “OK” to provide your Computer and Workgroup names.
6Enter your Computer Name, Workgroup Name, Computer Description,
and click on “Close.”
7When asked for the “Madge Networks Driver Disk”, click on “OK.”
8Insert drivers disk 2 of 2, set the path to “A:\” and click “OK.” (If you have
an HP preloaded HDD, set the path to “C:\LANDRV\MADGE\DISK2\”)
9Click on “Yes” to restart your computer and finish the installation.
1 Connecting to a Netware 3.12 Server
Windows 95 SR2
2 Connecting to a Netware 4.11 Server
Windows for Workgroups
2 Connecting to a Netware 4.11 Server
Windows for
Workgroups
Requirements
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
• Madge Smart 16/4 PCI TR adapter and drivers diskettes ver 4.4.
• Driver Name: Size: 59KB Date: 5/22/95
• Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
• Netware client for DOS and MS-Windows.
Device Configuration
• Interrupt 9 (2)
• I/O Address FCC0-h
Procedure
1With the HP Vectra turned off install the Madge Smart16/4 PCI TR
adapter card into a PCI slot.
2Power on the machine and boot to a DOS prompt.
3Insert Netware Client for DOS and Windows Disk 1 and execute
“A:\INSTALL.”
4Change the settings to match the following and then option 6 to continue
the installation.
• C:\NWCLIENT
•YES
•YES
• C:\WINDOWS
•No
• Madge Smart 16/4 PCI Ringnode
5Insert the corresponding diskettes to finish the file transfer, and then
reboot the machine.
2 Connecting to a Netware 4.11 Server
Windows for Workgroups
6After windows loads, open the “NETWORK” folder, and double-click the
“NETWORK SETUP” icon.
7Select “Networks” and verify that “Novell Netware (Workstation Shell 4.0
and above)” is optioned under “Install Windows support for the following
network only.”
8Click on “OK” twice, and the installation is complete.
2 Connecting to a Netware 4.11 Server
Windows 95 SR2
Windows 95 SR2 Requirements
• HP Vectra with Windows 95 SR2 installed.
• Madge Smart16/4 PCI TR adapter and drivers diskettes ver 4.4.
• Driver Name: Windows 95 Default
• Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
Device Configuration
• Interrupt 9 (2)
• I/O Address FCC0-h
Procedure
1Upon booting, Windows 95 will automatically recognize the adapter. Click
on “Next.”
2When prompted, click on “Other Locations.”
3Insert drivers disk 2 of 2, set the path to “A:\WIN95\RPL\” and click “OK.”
(If you have an HP preloaded HDD, set the path to
“C:\LANDRV\MADGE\DISK2\ WIN95\RPL\”)
4Verify that “Madge Smart 16/4 PCI Ringnode (BM) 2” is listed and click on
“Finish.”
5Click “OK” to provide your Computer and Workgroup names.
6Enter your Computer Name, Workgroup Name, Computer Description,
and click on “Close.”
7When asked for the “Madge Networks Driver Disk”, click on “OK.”
8Insert drivers disk 2 of 2, set the path to “A:\” and click “OK.”
(If you have an HP preloaded HDD, set the path to
“C:\LANDRV\MADGE\DISK2\”)
9Click on “Yes” to restart your computer and finish the installation.
2 Connecting to a Netware 4.11 Server
Windows 95 SR2
Otros manuales para Vectra VE4
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Hardware de computadora de HP
HP
HP StorageWorks XP128 Manual de usuario
HP
HP 4440B Manual de usuario
HP
HP Pavilion xl700 - Desktop PC Manual de usuario
HP
HP 381513-B21 - Smart Array P800 Controller... Manual de usuario
HP
HP GbE2c - Blc Layer 2/3 Fiber SFP Option Cómo utilizar
HP
HP 3000 Series Manual
HP
HP 64782 Manual de usuario
HP
HP F1381A Manual de usuario
HP
HP A3550A - High Availability Disk Arrays Model 20 Storage... Manual de usuario
HP
HP M8201R Manual de usuario
HP
HP 64793 Series Manual de usuario
HP
HP CB001A Manual de usuario
HP
HP E2416B Manual de usuario
HP
HP E2465A PowerPC 604 PGA Manual de usuario
HP
HP Visualize c100 Manual de usuario
HP
HP 6-Port SATA RAID Manual de usuario
HP
HP Nx9420 - Compaq Business Notebook Manual
HP
HP Smart Array P400 Instrucciones de uso
HP
HP 81200 Manual de usuario
HP
HP D7171A - NetServer - LPr Manual de instalación y operación
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
