HP D7171A - NetServer - LPr Manual de usuario
HP NetServer
Ultra3 SCSI Hot-Swap
Hard Disk Drive and Tray
User Guide
HP Part Number 5969-5922
Printed in February 2000
ii
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard shall not
be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software
on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced, or
translated to another language without the prior written consent of Hewlett-
Packard Company.
Hewlett-Packard Company
Network Server Division
Technical Communications/MS 45SLE
10955 Tantau Avenue
Cupertino, CA 95014-8059 USA
© Copyright 2000 Hewlett-Packard Company.
Audience Assumptions
The guide is for the person who installs, administers, and troubleshoots LAN
servers. Hewlett-Packard Company assumes you are qualified in the servicing of
computer equipment and trained in recognizing hazards in products with
hazardous energy levels.
iii
Contents
1 Introduction to Ultra3 Drives..........................................................................1
Overview............................................................................................................1
Ultra3 Drives are Low Voltage Devices.........................................................1
Ultra3 Drives Have Two Heights; Drive Cages Have Several Sizes.............1
Filler Panels...................................................................................................1
Disk Spacers .................................................................................................2
Verify Contents .................................................................................................. 2
2 Installation Procedure..................................................................................... 3
Installing the Ultra3 Disk Drive Module..............................................................3
Removing the Ultra3 Disk Drive Module............................................................8
Installing the Ultra3 Drive in a Tray (optional)....................................................9
3 Supported Configurations............................................................................11
4 Warranty and Support...................................................................................13
Hardware Warranty..........................................................................................13
HP Repair and Telephone Support..................................................................13
HP World Wide Web Site................................................................................13
5 Regulatory Information................................................................................. 15
Index.................................................................................................................... 17
1
1 Introduction to Ultra3 Drives
Overview
Ultra3 SCSI hot-swap hard disk drives provide higher I/O bandwidth and can
work with longer cable lengths than Ultra drives. Ultra3 drives operate at SCSI
bus data rates of up to 160 MB per second--double the rate of Ultra2 SCSI. With
Ultra3 drives, HP NetRAID environments and applications will show immediate
increases in performance.
Note: These drives are also backward compatible with Ultra2
controller systems.
Ultra3 Drives are Low Voltage Devices
Ultra3 drives have LVD (low voltage differential) signal levels. The low voltage
requirements allow the integration of the differential drivers and receivers into
drive SCSI controllers. LVD provides the signal quality necessary to run at Ultra3
data rates. LVD also allows for significantly longer SCSI bus cable lengths.
Ultra3 Drives Have Two Heights; Drive Cages Have Several Sizes
Ultra3 disk drive modules come in two heights: the 1-inch (2.5 cm) low profile
drive and the 1.6-inch (4 cm) half-height drive. NetServer drive cages come in
several sizes. There are two types of six-drive cages. The LH3, LH4, and RS-12
cages support a mix-and-match of 1-inch low profile drives and 1.6-inch (4 cm)
half-height drives. Other NetServers with six-drive cages support either 1-inch (2.5
cm) low profile drives or 1.6-inch (4 cm) half-height drives. Refer to your
NetServer manuals for details. Chapter 3 lists the places where the supported
configurations can be found.
Filler Panels
When you have fewer drives than the hot-swap cage supports, filler panels must be
inserted in empty disk locations. Filler panels ensure that the hot-swap cage has
the proper ventilation and air flow. You will remove the filler panel when you
insert a new Ultra3 disk drive module. (Figure 2-1 in the next chapter shows a
filler panel.)
Chapter 1 Introduction to Ultra3 Drives
2
Disk Spacers
When your hot-swap cage holds a mix of low profile and half-height drives, one
drive may require a disk spacer. The disk spacer fills empty space between one
drive and the adjacent drive. Disk spacers can be mounted on 1-inch (2.5 cm) low
profile drives or 1.6-inch (4 cm) half-height drives. (Figure 2-2 in the next chapter
shows a disk spacer.)
Verify Contents
The Ultra3 SCSI Hot-swap Hard Disk Drive and Tray Accessory Kit contains the
following items:
•Ultra3 SCSI hot-swap hard disk drive module
•disk spacer
•Ultra3 SCSI Hot-swap Hard Disk Drive and Tray User Guide
If anything is missing or damaged, call your reseller.
3
2 Installation Procedure
This chapter describes how to install the Ultra3 disk drive module in your
HP NetServer, and provides instructions for removing and storing the disk drive
module. Additionally, this chapter describes how to attach an Ultra3 drive to a hot-
swap tray.
Installing the Ultra3 Disk Drive Module
CAUTION Protect the Ultra3 disk drive module from static electricity by
leaving it in its antistatic bag until you are ready to install it.
Before handling the disk drive module, touch any unpainted
metal surface to discharge static electricity. When you remove
the disk drive module from the antistatic bag, handle it only by
the frame.
Do not touch the electrical components. Place the disk drive
module on the antistatic bag whenever you set it down.
Disk drive modules are very susceptible to mechanical shock
and can be damaged by a drop as short as one-quarter of an
inch (.5 cm). Take care when unpacking and handling the disk
drive module. If the drop would crack an egg, it will damage
the drive.
Chapter 2 Installation Procedure
4
1. If there is a filler panel in the drive location, remove the filler panel as
follows:
• Press the latch and insert your fingers.
• Using your fingers, pull the filler panel straight out.
Figure 2-1 shows a filler panel being removed from a system with a
six-drive hot-swap cage. Your HP NetServer’s enclosure may have a
four-drive cage or a two-drive cage.
Figure 2-1. Removing the Filler Panel
Chapter 2 Installation Procedure
5
2. Disk spacers attach to the disk drive module with four small feet.
To remove a disk spacer from the adjacent disk drive module:
• Slide the disk spacer back, a fraction of an inch (2.5 cm), away from
your body.
• Tilt up the front of the disk spacer to disengage the front two feet.
• Pull the disk spacer forward slightly, to disengage the back two feet and
lift.
Figure 2-2. Removing the Disk Spacer From a Disk Drive Module
To attach a disk spacer to a disk drive module:
• Tilt up the front of the disk spacer and engage the back two feet.
• Press the disk spacer back, a fraction of an inch (2.5 cm), away from
your body.
• Lower the front of the disk spacer into place to engage the front two
feet.
Chapter 2 Installation Procedure
6
3. On the Ultra3 disk drive module, press the blue latch in and pull the lever
out as far as it can go as shown in Figure 2-3. Pulling open the lever
retracts the locking tab on the side of the disk drive module. Be careful not
to use extreme force when pulling the lever.
Figure 2-3. Pulling Open the Lever Retracts the Locking Tab
on the Side of the Drive
4. Slide the Ultra3 disk drive module slowly into the drive location until it
stops. In some systems, drives are inserted horizontally (Figure 2-4); and in
other systems, drives are inserted vertically (Figure 2-5).
Be careful of the light pipes as you insert the drive. The light pipes are
fragile.
CAUTION You must insert the drive slowly and gently. The connector is
designed with some long pins that must make contact before
the short pins. If the disk drive module is inserted too quickly,
the short pins make contact too quickly after the long pins.
The in-rush current can cause the power supply to shut down.
5. Press the lever in, until you hear the latch click into place.
Otros manuales para D7171A - NetServer - LPr
117
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Hardware de computadora de HP
HP
HP ML570 - ProLiant - G2 Manual de usuario
HP
HP t628 Manual de usuario
HP
HP OmniBook 3100 Manual de usuario
HP
HP HP-UX 10.20 Manual de usuario
HP
HP USB 3.0 4-Port SuperSpeed PCIe x1 Card Manual de usuario
HP
HP F1381A Manual de usuario
HP
HP JG560A Manual de usuario
HP
HP Compaq t5500 Manual de usuario
HP
HP Smart Array P400 Instrucciones de uso
HP
HP rp7420 Manual de usuario
HP
HP 64793 Series Manual de usuario
HP
HP D7171A - NetServer - LPr Manual de usuario
HP
HP 64782 Manual de usuario
HP
HP RDX USB 3.0 Manual de instrucciones
HP
HP C-CLASS BLADESYSTEM 409513-B21 Instrucciones de uso
HP
HP Xw4600 - Workstation - 2 GB RAM Manual de usuario
HP
HP A3550A - High Availability Disk Arrays Model 20 Storage... Manual de usuario
HP
HP A1250 Series Instrucciones de montaje
HP
HP Z210 Series Manual de usuario
HP
HP E5000 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
