HP GbE2c - Blc Layer 2/3 Fiber SFP Option Cómo utilizar

HP BladeSystem c-Class

Solution Overview

Setup Poster

Intended audience

This document is for the person who installs, administers, and troubleshoots HP BladeSystem

c-Class products. Only persons experienced in server blade technology and configuration

should attempt these procedures. HP assumes you are qualified in the servicing of computer

equipment and trained in recognizing hazards in products with hazardous energy levels.

Legal notices

The information contained herein is subject to change without notice. The only warranties for

HP products and services are set forth in the express warranty statements accompanying such

products and services. Nothing herein should be construed as constituting an additional

warranty. HP shall not be liable for technical or editorial errors or omissions contained

herein.

Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.

Part Number 413339-005

September 2008 (Fifth Edition)

Document overview

This document provides an overview of the complete installation process of an HP

BladeSystem c-Class solution.

In this document, the term "blade" can include server blades, storage blades, or

workstation blades.

1Before you begin

A. Research and develop a solution

To begin researching the HP BladeSystem solution, see the HP BladeSystem

technical resources website

(http://www.hp.com/go/bladesystem/documentation). The website includes

white papers, tech briefs, instructions, best practices, helpful hints, useful links, and

suggestions for setting up and configuring the solution.

The website includes the following tabs:

•Plan your Solution.

Use this tab to plan and learn about the information and tools required to

select the optimal BladeSystem solution.

•Install your Solution.

This tab provides procedures for completing a quick installation or for

executing a comprehensive installation of your BladeSystem solution. This

section also includes detailed port mapping information.

•Maintain and Troubleshoot.

Maintenance and troubleshooting information are provided. This tab also

includes useful links to HP BLadeSystem c-Class firmware and software

upgrades and driver downloads.

•Functionality and Value.

Learn about the functionality and value of HP BladeSystem technologies and

the value of BladeSystem solutions.

B. Unpack the system

The enclosure and components ship with hard copy installation instructions. When

unpacking, be sure to locate all hard copy installation instructions.

C. Compile the documentation

The documentation, while delivered individually and in various formats, works as a

system. Consult these documents before attempting installation. These documents

provide required important safety information and decision-making steps for

configuration.

•The enclosed documentation includes the following:

oThe printed rack template

oThe Solution Overview poster

oc3000 or c7000 Enclosure Quick Setup Instructions

oc3000 or c7000 Enclosure Documentation CD, including safety

information, the enclosure setup and installation guide, and other useful

links

•The following items are available on the HP Bladesystem documentation

website (http://www.hp.com/go/bladesystem/documentation):

oUseful links to BladeSystem technical information like Quick Specs and

Customer advisories

oThe installation checklist, used to collect information needed for

installation and configuration

oUser documentation, such as user guides, quick install cards, and

troubleshooting information

oCopies of all the material included with the enclosure

oNumerous white papers and technical briefs on various BladeSystem

components.

D. Determine power and cooling configurations

Validate power and cooling requirements based on location and installed

components.

E. Plan device and interconnect mappings

•Onboard Administrator to iLO port mappings

The blade iLO ports and interconnect module ports can obtain IP addresses

on the management network in three ways: a DHCP server, static IP address

assignment, or enclosure bay IP addressing (EBIPA).

For more information, see the HP BladeSystem Onboard Administrator User

Guide on the HP website

(http://www.hp.com/go/bladesystem/documentation).

•Interconnect bay to mezzanine slot mappings

Blade mezzanine slots correspond to specific interconnect bays. Plan

mezzanine-to-interconnect mapping before installing interconnect modules

and blade mezzanine options.

For more information, see the appropriate HP BladeSystem enclosure setup

and installation guide on the HP website

(http://www.hp.com/go/bladesystem/documentation).

•Interconnect bay to physical cable mappings

Determine and acquire the appropriate number of cables, cable types, and

lengths for the interconnect devices being installed.

For more information, see the documentation that ships with the interconnect

devices.

2Hardware installation

See the enclosure quick setup instructions, rack template, and applicable

installation instructions.

A. Install the enclosure

The enclosure can be installed either in a rack or rack-free environment. The

c3000 enclosure is also available in a tower model. For rack installations, install

the rack rails, and then install the enclosure and other components.

B. Install the components

Before installing front or rear components into the enclosure, review enclosure bay

numbering for each component.

Install any options, such as processor, memory, mezzanine card, or hard drive,

into each blade.

Based on the total number ordered and the planned configuration, install the

following components:

•Blades

•Onboard Administrator modules

•Power supplies

•Active cool fans

For installation instructions, see the appropriate enclosure setup and installation

guide.

C. Connect the Onboard Administrator module

cabling

Use the appropriate cables to connect each installed Onboard Administrator

module to the external connections. The connectors on the Onboard Administrator

module provide a connection to the iLO management network and the capability

to link multiple enclosures.

IMPORTANT: For proper management of enclosure devices

there must be an Ethernet connection from the Onboard

Administrator module to the external management network.

For information on Onboard Administrator module cabling,

see the HP BladeSystem Onboard Administrator User

Guide.

D. Install the interconnect modules and connect

cabling

Install the interconnects based on the type of fabric in the configuration and the

planned installation location of each mezzanine card. Use the appropriate cables

to connect each installed interconnect module to the network.

E. Power up the enclosure

Connect the AC or DC power cables, depending on the power configuration.

When the circuit breakers are powered, the enclosure and HP BladeSystem Insight

Display have power. By default, each installed component also powers up.

Examine the HP BladeSystem Insight Display for any errors which may prevent

installed components from powering up.

3Enclosure configuration

A. Run the Insight Display wizard

When the enclosure is powered up for the first time, the HP BladeSystem Insight

Display launches an installation wizard to guide the rack technician through the

initial configuration process.

Be sure to have the Installation Checklist available to record important information,

such as the Onboard Administrator IP address, gathered while running the

installation wizard. By default, the Onboard Administrator obtains an IP address

using DHCP. Read the Insight Display and write the IP address for the active and

standby Onboard Administrator on the checklist. This IP address is needed for

remote connection and subsequent setup with a browser. If DHCP is not used, a

static IP address can be configured on the Insight Display Settings screen. For

specific instructions, see the HP BladeSystem Onboard Administrator User Guide

on the HP website (http://www.hp.com/go/bladesystem/documentation).

The Insight Display verifies that no installation or configuration errors exist and

indicates configuration check progress. If configuration errors are indicated, follow

the on-screen instructions to correct the problem. When the screen display stays

green, there are no configuration errors or device failures and hardware

installation is complete.

B. Run the Onboard Administrator First Time Setup

Wizard

After all hardware is installed and the hardware configuration has been verified in

the Insight Display, use one of the following methods to complete the enclosure

configuration setup:

•Use the Insight Display to determine the address received by DHCP, and then

use the Onboard Administrator First Time Setup Wizard to complete the

installation and configuration at the assigned address.

•If no DHCP server is present on the customer management network, do one

of the following:

oUse the Insight Display to set the address, and then use the Onboard

Administrator First Time Setup Wizard to complete the installation and

configuration at the assigned address.

oUse the Onboard Administrator First Time Setup Wizard or the CLI to

configure EBIPA and assign IP addresses for iLO and interconnect

management ports. This method simplifies the required setup for

interconnect management network settings.

•Use the Insight Display to set the IP address and complete the Onboard

Administrator First Time Setup Wizard from the Insight Display. This method

enables configuration without the use of an external browser.

For specific instructions, see the HP BladeSystem Onboard Administrator User

Guide on the HP website (http://www.hp.com/go/bladesystem/documentation).

4Interconnect module configuration

Each interconnect module ships with a default configuration. For customized

configuration or advanced port mapping, see the installation instructions that ship

with each interconnect module.

To configure HP Virtual Connect modules, see the HP Virtual Connect for c-Class

BladeSystem User Guide on the HP website

(http://www.hp.com/go/bladesystem/documentation).

5Firmware Management

To determine recommended updates and download the latest firmware, see the HP

BladeSystem c-Class Firmware and Upgrades Compatibility Matrix on the HP

website (http://www.hp.com/go/bladesystemupdates).

If you are operating the enclosure in a Microsoft® Windows® or Linux OS

environment, use the following tools to verify and update the firmware:

•HP Smart Update Manager

The HP Smart Update Manager utility is available from the ProLiant Firmware

Maintenance CD. This CD and others can be downloaded free-of-charge

from the HP website (http://www.hp.com/support).

•Online ROM Flash Component Utility

The Online ROM Flash Component Utility enables system administrators to

efficiently upgrade system or controller ROM images across a wide range of

servers and array controllers. To download the tool and for more

information, see the HP website (http://www.hp.com/support).

If you are operating the enclosure in a VMWare ESX OS environment, use an

offline utility such as ROMPaq to update and verify the firmware. The ROMPaq

utility checks the system and provides a choice (if more than one exists) of

available firmware revisions.

For more information about the ROMPaq utility, see the HP website

(http://www.hp.com/support).

6Operating system installation

If the blade has an OS that is pre-installed, proceed to section 7, "Management

software (on page 7)".

A. Choose a supported operating system

For the latest operating system support information, see the HP website

(http://www.hp.com/go/supportos).

B. Install an operating system

To install an operating system, use one of the following methods:

•Use iLO Virtual CD/DVD-ROM to install the operating system from a

CD/DVD-ROM drive on the network.

For more information, see the server blade user guide and the HP Integrated

Lights-Out 2 User Guide on the HP website

(http://www.hp.com/servers/lights-out).

•Use a USB DVD-ROM drive and a local I/O cable to install the operating

system locally.

For more information, see the server blade user guide.

•For c3000 enclosures, use the optional integrated DVD-ROM drive to install

the operating system.

For more information, see the HP BladeSystem c3000 Enclosure Setup and

Installation Guide on the HP website

(http://www.hp.com/go/bladesystem/documentation).

•Use the Rapid Deployment Pack to install the operating system.

The RDP software is the preferred method for rapid, high-volume server

deployments. The RDP software integrates two powerful products: Altiris

Deployment Solution and the HP ProLiant Integration Module.

The intuitive graphical user interface of the Altiris Deployment Solution

console provides simplified point-and-click and drag-and-drop operations that

enable you to deploy target servers, including server blades, remotely. It

enables you to perform imaging or scripting functions and maintain software

images.

For more information about the RDP, refer to the HP ProLiant Essentials Rapid

Deployment Pack CD or refer to the HP website

(http://www.hp.com/servers/rdp).

7Management software

A. Deploy the management software

The HP BladeSystem c-Class enclosure ships with the Insight Control Management

DVD, an integrated suite of software used to simplify HP BladeSystem provisioning

and management.

Use the wizard-based installer to configure and license HP Systems Insight

Manager (HP SIM) and ProLiant Essentials management software rapidly and

consistently, which reduces manual procedures and enables faster production

deployment of HP BladeSystem servers.

If previous enclosures have been installed, it is not necessary to deploy the

management software. New devices are discovered and can be managed by the

previously installed management system.

Before deploying the management software and creating provisioning policies:

•Complete the installation checklist.

•Be sure that the HP BladeSystem enclosure, switches, and associated storage

resources are configured.

•Verify that a supported operating system is installed. If the operating system

has not been installed, see the operating system installation documentation.

Launch the Insight Control Management DVD and use the installation wizard to

deploy and configure HP Systems Insight Manager (HP SIM) and ProLiant

Essentials management software. After installation completes, log in to HP SIM

using the credentials supplied during the installation process, and follow the

instructions on the Getting Started pop-up to complete installation and

configuration.

For more information, see the HP Insight Control Management Software portfolio

at the HP website

(http://h18013.www1.hp.com/products/servers/management/index.html?jumpi

d=servers/proliant/manage).

B. Discover and provision new devices

Use HP SIM to discover HP BladeSystem resources and view those resources

through the integrated BladeSystem manager. For further information, see the

Insight Control Management Quick Setup Poster.

C. Troubleshooting

To troubleshoot any issues, use the Enclosure Insight Display or see the enclosure

troubleshooting guide.

Otros manuales para GbE2c - Blc Layer 2/3 Fiber SFP Option

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de HP

HP A1250 Series Instrucciones de montaje

HP 64793 Series Manual de usuario

HP Vectra VE4 Manual de usuario

HP FlexFabric 12908E LSXM108XFAN Manual de usuario

HP 82718A Manual de usuario

HP CB001A Manual de usuario

HP HPE LSWM2XGT2PM Manual de usuario

HP Z400 - Workstation Manual de usuario

HP P Class 450/500/550/600/650/700/750 Manual

HP Model 744 - VME Workstation Manual de usuario

HP D7171A - NetServer - LPr Manual de instalación y operación

HP Smart Array P400 Instrucciones de uso

HP ML570 - ProLiant - G2 Manual de usuario

HP Xw8400 - Workstation - 4 GB RAM Manual de usuario

HP Xw4600 - Workstation - 2 GB RAM Manual de usuario

HP Wireless USB Network Adapter hn215w Manual de usuario

HP MCS-200 Manual de usuario

HP Model 744 - VME Workstation Manual de usuario

HP Adaptive Rack Cooling System Guía del usuario

HP NC364T Manual de usuario

HP 64782 Manual de usuario

HP 64751 Manual de usuario

HP E3473A Manual de usuario

HP 3000 Series Manual

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario