HP HPE LSWM2XGT2PM Manual de usuario

HPE LSWM2XGT2PM Interface Card

(JH156A) User Guide

Part number: 5998-7834s

▌Introduction

Product

code HPE description Alias

JH156A HPE 5130/5510 10GBASE-T

2-port Module LSWM2XGT2PM

Overview

The LSWM2XGT2PM interface card provides two 1/10GBase-T

Ethernet ports.

Figure 1 LSWM2XGT2PM interface card

(1) 1/10GBase-T Ethernet

port LED

(2) 1/10GBase-T Ethernet port

(3) Captive screw (4) Ejector lever

NOTE:

The switch models that the LSWM2XGT2PM interface card are

applicable to may change over time. For the most recent list of

applicable switch models, contact HPE Support or marketing

staff.

1/10GBase-T Ethernet ports

Table 1 1/10GBase-T Ethernet port specifications

Item Specification

Connector type RJ-45

Port standard 1/10 Gbps full duplex, MDI/MDI-X

auto-sensing

Transmission medium

and max transmission

distance

•Category-6 unshielded twisted pair

cable: 55 m (180.45 ft)

•Category-6 shielded twisted pair

cable: 100 m (328.08 ft)

•Category-6A or above twisted pair

cable: 100 m (328.08 ft)

Compliance standard

•IEEE 802.3an

•IEEE 802.3ab

LEDs

Each 1/10GBase-T port on the LSWM2XGT2PM interface card has

an LED to indicate its operating status.

Table 2 describes LEDs for the QSFP+ ports.

Table 2 1/10GBase-T port LED descriptions

LED status Description

Steady green The port is operating at 10 Gbps, and a link is

present on the port.

Flashing green The port is sending or receiving data at 10

Gbps.

Steady yellow The port is operating at 1 Gbps, and a link is

present on the port.

LED status Description

Flashing yellow The port is sending or receiving data at 1 Gbps.

Off No link is present on the port.

NOTE:

The 1/10GBase-T port LEDs are not affected by the port mode

switching button on your switch. For more information about the

port mode switching button, see the installation guide of the

switch.

▌Installing and removing an interface card

CAUTION:

•Before you install or remove an interface card, wear an ESD

wrist strap and make sure the wrist strap makes good skin

contact and is reliably grounded.

•To avoid device damage, do not use excessive force when you

install or remove an interface card.

This example describes how to install and remove LSWM2XGT2PM

interface card on an HPE 5510 24G 4SFP+ HI 1-slot Switch

(JH145A).

Prepare the following tools before you install or remove an interface

card:

•Phillips screwdriver.

•Flat blade screwdriver.

•ESD wrist strap.

The installation tools are not provided with HPE devices. Prepare

them yourself.

Installing an interface card

Removing a filler panel

1. Use the Phillips screwdriver to remove the screw on the filler

panel in the target interface card slot, as shown by callout 1

in Figure 2.

2. Insert the flat blade screwdriver through the handle on the filler

panel to pull out the filler panel, as shown by callout 2 in Figure 2.

Figure 2 Removing a filler panel

NOTE:

Keep the removed screw and filler panel secure for future use.

Installing an LSWM2XGT2PM interface card

1. Unpack the interface card.

2. Insert the interface card slowly into the slot along the guide rails,

as shown by callout 1 in Figure 3.

3. Rotate inward the ejector lever as shown by callout 2 in Figure 3

until the interface card is in close contact with the switch.

4. Use the Phillips screwdriver to tighten the captive screw on the

interface card, as shown by callout 3 in Figure 3.

Figure 3 Installing an LSWM2XGT2PM interface card

Removing an interface card

CAUTION:

•Before you remove an interface card, remove the cable from it.

•After removing an interface card, if no new interface card is to

be installed, install the filler panel as soon as possible to

prevent dust and ensure good ventilation in the device.

Removing an LSWM2XGT2PM interface card

1. Prepare an anti-static bag.

2. Use the Phillips screwdriver to loosen the captive screw on the

interface card, as shown by callout 1 in Figure 4,

3. Rotate outward the ejector lever as shown by callout 2 in Figure 4.

4. Pull out the interface card slowly out the interface card slot as

shown by callout 3 in Figure 4.

5. Place the removed interface card in the anti-static bag.

Figure 4 Removing an LSWM2XGT2PM interface card

Verifying the installation

After the installation is complete, identify whether the interface card is

operating correctly according to the status of the 1/10GBase-T port

LEDs.

If the interface card fails to operate correctly, perform the following

steps:

1. Reinstall it following the installation procedures described in this

document.

2. If the problem persists, contact HPE Support.

▌Documentation

To access documentation and support services, go to the Hewlett

Packard Enterprise Support Center website:

www.hpe.com/support/hpesc

The information in this document is subject to change without notice.

BOM: 3101A0JL

Version: 6PW103

5998-7834s

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de HP

HP OmniBook 3100 Manual de usuario

HP F1381A Manual de usuario

HP 82718A Manual de usuario

HP GbE2c - Blc Layer 2/3 Fiber SFP Option Cómo utilizar

HP ML570 - ProLiant - G2 Manual de usuario

HP 81200 Manual de usuario

HP 6600 FIP-20 Flex Instrucciones de montaje

HP D7171A - NetServer - LPr Manual de usuario

HP Xw4600 - Workstation - 2 GB RAM Hoja de instrucciones

HP NC550SFP Manual de usuario

HP 5930-4Slot Manual de usuario

HP Smart Array P400 Instrucciones de uso

HP Model 744 - VME Workstation Manual de usuario

HP Adaptec ultra p2280a Manual de usuario

HP Kayak XW U3-W3 Manual de usuario

HP 273914-B21 - Smart Array 6404/256 RAID... Manual de usuario

HP CB001A Manual de usuario

HP RDX USB 3.0 Manual de instrucciones

HP 98625A Manual de usuario

HP Adaptive Rack Cooling System Guía del usuario

HP StoreOnce 2700 Manual del operador

HP 4440B Manual de usuario

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manual de usuario

HP QMH2572 8Gb FC HBA Instrucciones de uso

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario