Honeywell KEGS5000 Manual de usuario

1 of 3

CONFIGURING THE KEGS5000 FOR STANDALONE OR SLAVE USE

The KEGS5000 has two versions of firmware loaded. Stand Alone and Slave

Standalone Firmware is the default operating mode and is intended for the direct control of

KD6 domes and Ultrak multiplexes

Slave firmware is intended to operate in two different modes.

Mode1: KSX3208L matrix and MXSYS04E controller mode.

Mode2 : Maxpro MAX1000 control (Slave firmware version 2.02.36 or later)

Note: Earlier versions of the slave firmware do not support Maxpro Mode. Should this mode be

required download the firmware and instructions from the Ultrak website

http://www.ultrak.com/Download_Registrations/Software_Downloads/Index.htm

Checking

the version

of firmware

To determine which version of firmware the KEGS5000 is running cycle the power and check

the LCD display for one of the following sequences.

Stand Alone Firmware

Slave Firmware

Boot Manager

1.64

Boot Manager

1.64

Booting In

5..4..3 Booting In

5..4..3

KEGS5000

040112 V1.03.11 KEGS5000 Slave

040112 V2.02.36

Loading Defaults

Address 1

System Login

Password: ---- Keyboard Off line

2 of 3

CONFIGURING THE KEGS5000 FOR STANDALONE OR SLAVE USE, CONTINUED

Boot Manager

1.64

Configure

KEGS5000

for

Standalone

or Slave

modes

1. Cycle power on the KEGS5000.

Booting In 5..4..3

2. Before the counter reaches zero. Press the 1 key.

Enter Password ----

3. Enter the password 1994

4. Use the arrows key under the LCD display to select

Slave Mode. Press Enter to run this mode. or

Slave Mode

Note: this mode is for use with the KSX3208L, MXSYS04E or

MAX1000

5. Use the arrows key under the LCD display to select

Standalone Mode. Press Enter to run this mode. <Run Bank>

Standalone Mode

Note: this mode is for use with the KD6 domes and Ultrak

multiplexes

3 of 3

CONFIGURING THE KEGS5000 FOR STANDALONE OR SLAVE USE, CONTINUED

The KEGS5000 must be running the Slave firmware as described above.

Boot Manager

1.64

Configure

KEGS5000 in

slave mode

to work with

KSX32080/

MXSYS04E

or MAXPRO

1. Cycle power on the KEGS5000.

Booting In 5..4..3

2. Let the conter reach zero.

3. While the version number is displayed press the Menu

button (Middle button under LCD Display) KEGS5000 Slave

040112 V2.02.36

Note: The version number only dsplays for 2 seconds. Should

you miss this time window then recycle the power and

start again.

KB Mode: Slave

1: Slave 2: Maxpro

4. Select the mode using the 1 or 2 key.

1 is for Slave mode (KSX32080 and MXSYS04E use)

2 is for use with Maxpro MAX1000

5. Press Enter when done.

Stick Range: Hi

1: Hi 2:Lo

6. Select the Joystick range. Use Hi for KSX32080 and

MXSYS04E use. Use Hi or Lo for Maxpro use.

Press Enter when done.

7. Select the Baud rate. Use 19k2 for Maxpro and 9600

for KSX32080 and MXSYS04E use.

Press enter when done Baud Rate: 19K2

1: 9600 2:19k2

Otros manuales de Transmisor de Honeywell

Honeywell

Honeywell ST 3000 Manual de usuario

Honeywell

Honeywell MCE 2 Manual de usuario

Honeywell

Honeywell oneWireless XYR 6000 Manual de usuario

Honeywell

Honeywell ST 800 Series Manual de instrucciones

Honeywell

Honeywell 5820L - Slim Line Wireless Door/Window... Instrucciones de montaje

Honeywell

Honeywell DACT-E3 Manual técnico

Honeywell

Honeywell XYR 5000 Series Manual de usuario

Honeywell

Honeywell OELD Manual de usuario

Honeywell

Honeywell SmartLine ST700 Manual de usuario

Honeywell

Honeywell ADEMCO 5804-2 Manual de usuario

Honeywell

Honeywell Satellite XT Manual de usuario

Honeywell

Honeywell HVB16TPTX Manual de usuario

Honeywell

Honeywell XYR 5000 Series Manual de usuario

Honeywell

Honeywell 5815 - Ademco - Wireless Door Manual de usuario

Honeywell

Honeywell XNX Universal Transmitter Manual de usuario

Honeywell

Honeywell oneWireless XYR 6000 Manual de usuario

Honeywell

Honeywell STT850 Series Manual de usuario

Honeywell

Honeywell XNX Manual de usuario

Honeywell

Honeywell XNX-AM Series Manual de usuario

Honeywell

Honeywell Ademco 5804AP Manual de usuario

Honeywell

Honeywell ST 3000 Manual de usuario

Honeywell

Honeywell STT850 SMARTLINE Manual de usuario

Honeywell

Honeywell STT850 SMARTLINE Manual de usuario

Honeywell

Honeywell RESCU 406AFN Guía de configuración

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manual de usuario