Honeywell Ademco 5804AP Manual de usuario

N7674-3 4/05 PRELIMINARY

Honeywell International Inc. 5804AP

WIRELESS KEY

TRANSMITTER

INSTALLATION INSTRUCTIONS

For use with QED control panels ONLY!

GENERAL INFORMATION

The 5804AP is a compact, 4-button portable

wireless transmitter intended for use only

with wireless alarm systems that support

QED 5800AP series receivers. Each button

on the transmitter may be programmed for

any zone response, but is typically used for

arming, disarming, panic, and relay

activation. Each button's response is

assigned when programming the transmitter

at the control (see the QED control's

installation instructions).

The 5804AP is powered by two replaceable

lithium batteries designed to provide up to 4

years of life. For battery installation, see

Battery Access.

PROGRAMMING THE 5804AP

Each 5804AP is assigned a unique serial

number during manufacture. Each button on

the unit also has a distinct "loop" number

(refer to Figure 1 that you must programme

into the QED control panel during

installation. Assign each button to an

individual zone and designate the Input Type

as "BR" (Button Type RF). You must

program the lower left-hand button (Loop 4;

see Figure 1). If it is not programmed, a

"check" condition will occur when the button

is accidentally pressed.

You can also program the unit by entering

the serial number manually through a

keypad or by downloading it to the control

panel using Ademco's V-LINK Downloading

Software (Rev. 4 or higher). If you use one of

these methods, be sure to include the loop

number of each button (see Figure 1).

For complete details on how to program the

5804AP transmitter's serial number at the

control panel, see the QED control unit's

installation instructions.

Note: Buttons on this transmitter must be

pressed for at least 1/2 second to activate the

transmitter. This feature minimizes the

possibility of accidental transmissions.

YOU MUST

PROGRAMME

THIS BUTTON

LOOP 3

LOOP 1

LOOP 2

LOOP 4

Figure 1: 5804AP showing button designations

If you choose not to use the lower left-hand

button (Button 4), do the following:

1. Program it into the system anyway (see

previous explanation).

2. After the serial number has been

programmed, re-enter Zone Programming

for that zone.

3. At the "Zone Type" prompt, enter 00 and

press [*]. On VISTA 20/4111XM panels,

the system will ask whether you want to

permanently delete that zone. Enter 0

(No). This will cause the system to retain

the serial number, but render the button

inactive. On 4140XMPT2/VISTA-120

panels and above, continue to press [*]

until you see the "Enter Zone No?"

prompt. At this point, press 00 and [*].

Then enter *99 to exit program mode.

INSTALLING ADHESIVE LABELS AND

BUTTONS

The 5804AP is supplied with colored buttons

(red and blue) and colored adhesive

identification labels (blue, red, gray, and

green). Each label has a specified command

function and symbol printed on it, as well as

an adhesive back for easy pasting.

To paste a label on a button, slowly peel

off a label with a selected function and paste

it on the button of the transmitter. If you

decide later to reprogram a button, the label

can be easily removed or a new label pasted

over the existing one.

Additional colored buttons (red and blue) are

also provided which can be used with or

without the labels. The buttons can be

inserted only in the areas provided for them

(see Figure 3).

To insert the colored buttons, do the

following:

1. Holding the transmitter with the buttons

face down, remove the case back by using

the blade of a small screwdriver to pry it

open (see Figure 2).

2. Carefully remove the PC board by its

rubber casing, making sure the board

does not come out of the casing. Do not

bend the exposed battery tabs on the PC

board.

3. Replace the desired buttons, either red or

blue, in each button's designated opening

(see Figure 3).

4. When finished, replace the PC board,

making sure the button tabs on the board

face the four buttons, and snap the case

front and back together.

After inserting the new buttons, you may

wish to check the 5804AP for proper

operation.

Battery Tabs Shown

Figure 2: Battery tabs shown.

Blue

Red

Figure 3: 5804AP shown open,

buttons facing down.

SPECIFICATIONS

Transmission Frequency: 315 MHz

Unit Dimensions:

57mm x 38mm x 12.7mm

+ POS. end

must face down

+ POS. end

must face down

BATTERY ACCESS

Battery:

Maxell CR2025, Duracell DL 2025 or Varta

CR2025

Battery Access:

Remove case back by using the blade of a

small screwdriver to pry open. Place

batteries in case back locations (see Figure

4).

+ POS END MUST FACE DOWN.

To close, snap case front and back together.

Important Note: Do not remove Printed

Circuit Board.

FCC ID: CFS8DL5804AP

PART 15 STATEMENT

THIS DEVICE COMPLIES WITH PART

15 OF THE FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY

NOT CAUSE HARMFUL

INTERFERENCE, AND (2) THIS DEVICE

MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL WITH

WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION, AND FOR DETAILS

REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

Honeywell International Inc.

165 Eileen Way, Syosset, New York 11791

Tabla de contenidos

Otros manuales de Transmisor de Honeywell

Honeywell

Honeywell SMV 3000 Manual de usuario

Honeywell

Honeywell K595 Manual de usuario

Honeywell

Honeywell XYR 5000 Series Manual de usuario

Honeywell

Honeywell STT700 SmartLine Guía del usuario

Honeywell

Honeywell oneWireless XYR 6000 Manual de usuario

Honeywell

Honeywell STT850 Series Manual de usuario

Honeywell

Honeywell XNX-AM Series Manual de usuario

Honeywell

Honeywell HVB16TPTX Manual de usuario

Honeywell

Honeywell oneWireless XYR 6000 Manual de usuario

Honeywell

Honeywell ADEMCO 5820L Instrucciones de montaje

Honeywell

Honeywell ST 800 Series Manual de usuario

Honeywell

Honeywell 5878 - Wireless Wall Transmitter Manual de usuario

Honeywell

Honeywell STD110 Manual de usuario

Honeywell

Honeywell 5816 Instrucciones de montaje

Honeywell

Honeywell ST 3000 Manual de usuario

Honeywell

Honeywell 5804 - Ademco Wireless Key Manual de usuario

Honeywell

Honeywell SMV800 Manual de usuario

Honeywell

Honeywell oneWireless XYR 6000 Manual de usuario

Honeywell

Honeywell SMV800 Manual de usuario

Honeywell

Honeywell ST 3000 Manual de usuario

Honeywell

Honeywell ST 800 Series Manual de usuario

Honeywell

Honeywell 5894PI - Ademco Wireless PIR Motion Sensor Manual de usuario

Honeywell

Honeywell PW Series Manual de usuario

Honeywell

Honeywell STT700 SmartLine Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manual de usuario