Honeywell 5817CBXT Manual de usuario

The 5817CBXT is a universal contact-monitoring transmitter

that can be used with household and commercial fire and

burglary-initiating devices such as door/window contacts,

motion and glassbreak detectors, sprinkler water flow

switches, tamper switches, post indicator valves, manual

pull stations and remote duct detectors. Upon activation, it

emits an RF signal to a control panel, sending a burglary or

fire alarm to a central station.



input loops (zones)



supervised and typically used for

high-priority alarm reporting such

as commercial fire or burglary

(reporting transmission every

four seconds)



normally closed reed switch used in

conjunction with magnet



closed household burglary loop. All

three loops may be used.



loop contains two tamper switches

to protect the 5817CBXT



commercial fire and burglary

1. Remove the transmitter cover by

inserting the flat blade of a small

screwdriver into the pry-off slot at the

bottom end of the unit (on the right

side closest to the cover’s decorative

ribs and twisting).

2. Disengage the supplied mounting

plate from the unit by inserting the

blade of a small screwdriver into the

mounting plate release hole (see

Diagram 2) and pushing the locking

tab out (see Diagram 1). Slide the

mounting plate downward along the

case back.

Note: For this application, the

alignment guide strip along one edge

of the mounting plate serves no

function and may be broken away,

if desired.

3. If concealed wiring is to be used,

feed the wires through the concealed

wiring entry hole on one corner of the

plate (surface wiring is mentioned in

step 5 below).

4. Install the mounting plate, with its

caseholding posts pointing up, in the

location selected as described in the

installation instructions. Use the two

flat-head screws supplied. Note: To

ensure proper operation of the unit’s

back tamper (when it is separated

from the mountain plate), the screws

must be anchored to a wall stud or

other solid wood material.

5. Set the DIP switch (after the

control panel has enrolled the

transmitter’s input ID’s) for the

desired primary loop characteristics,

as described in the table on the

following page.

Features

MOuNtING

5817CBXt





- 1-9/16" W x 3-1/2" H x 1-3/16" D

(40mm x 89mm x 30mm)









 

 

 

 

 

1610







5817CBXt Wireless Commercial Transmitter

5817CBXt











Honeywell Security Products Americas

2 Corporate Center Dr. Suite 100





1.800.467.5875

www.honeywell.com

Figure 1. Mounting Plate

Figure 2. Case Back

Figure 3. 5817CBXT Transmitter, Top Cover Removed

Figure 1. Mounting Plate

Figure 2. Case Back

Figure 3. 5817CBXT Transmitter, Top Cover Removed

Figure 1. Mounting Plate

Figure 2. Case Back

Figure 3. 5817CBXT Transmitter, Top Cover Removed



installations, multiple initiating devices may be used as long as the devices all service the same function such as door/window contacts, motion or



14-22AWG wire.

Notes: a. In order for the control panel to enroll the transmitter, the DIP switches must be Set to OFF-ON-ON-OFF (see Diagram 2).

b. The auxiliary loops are not affected by the DIP switch settings.

Wiring Connections

Connect the loop wiring to the unit’s terminals before installing the battery (see Diagram 2).

Notes: a. Primary loop 1 is a supervised loop and must have an end-of-line (EOL) resistor (470K ohms, supplied) placed across the sensor.

Additionally, for primary loop 1, a contact device may not be installed more than 20 feet from the transmitter.

b. If loop 2 is not going to be used, the magnet is not necessary.

c. If loop 3 is not going to be used, no connection is needed across its terminals. For UL household burglary and ﬁre installations, the loop 3

contact device (if used) may not be more than 3 feet from the transmitter.

Primary Loop Options Table

Switch

Setting

DIP Switch Position

On Repeating transmission (every 4 sec.) upon primary loop fault use high priority alarm, such as ﬁre.

Off Single transmission per primary loop change-of-state.

Tabla de contenidos

Otros manuales de Transmisor de Honeywell

Honeywell

Honeywell 5800Micra - Single Door/window Transmitter Manual de usuario

Honeywell

Honeywell XYR 5000 Series Manual de usuario

Honeywell

Honeywell 5800 Mini Manual de usuario

Honeywell

Honeywell 5820L - Slim Line Wireless Door/Window... Instrucciones de montaje

Honeywell

Honeywell XNX Manual de usuario

Honeywell

Honeywell Midas S2 Manual de usuario

Honeywell

Honeywell 5814 - Ademco Ultra-small Wireless... Manual de usuario

Honeywell

Honeywell ADEMCO 5869 Instrucciones de montaje

Honeywell

Honeywell SMV 3000 Manual de usuario

Honeywell

Honeywell STT25D Manual de usuario

Honeywell

Honeywell Midas S2 Manual de usuario

Honeywell

Honeywell 5818 Instrucciones de montaje

Honeywell

Honeywell ADEMCO 5817 Instrucciones de montaje

Honeywell

Honeywell TCC800MS Manual de usuario

Honeywell

Honeywell ADEMCO 5811 Manual de usuario

Honeywell

Honeywell STT700 STT700 Manual de usuario

Honeywell

Honeywell Fema Moduflex F Series Manual

Honeywell

Honeywell 5822T Manual de usuario

Honeywell

Honeywell ST 3000 Instrucciones de instalación y funcionamiento

Honeywell

Honeywell SMV800 Manual de usuario

Honeywell

Honeywell STDW810 Manual de usuario

Honeywell

Honeywell ADEMCO 5801 Instrucciones de montaje

Honeywell

Honeywell SMV800 Manual de instrucciones

Honeywell

Honeywell NOTIFIER AFL-RM Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manual de usuario