Honeywell ADEMCO 5869 Instrucciones de montaje

K5299V4 2/10 Rev. B

ADEMCO 5869

Holdup Switch/Transmitter

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The ADEMCO 5869 Holdup Switch/Transmitter is a inger-

operated RF transmitting device used or activating a

holdup signal at the security system control, and/or any

other security application. The 5869 is typically mounted

under a counter or money draw or inconspicuous operation.

When the transmitter is activated, it sends an RF signal to

the control panel, which then sends a burglary alarm to the

central station.

Once the 5869 trigger (Figure 1) is activated, the supplied

reset key K4563 must be used to reset the device. The 5869

also contains tamper switches that are activated either

when the cover is removed, or when the unit is orcibly

removed rom its installation location.

The 5869 has a permanent serial number assigned during

manu acture used or enrolling the 5869 with the security

system control panel. To enroll the 5869, re er to the

respective Security System Control Panel Installation and

Setup Guide.

For certified UL installations, the 5869 must be used

with the 5881ENHC tam er- rotected wireless

receiver, mounted inside its lastic enclosure and

outside the alarm anel enclosure.

PROGRAMMING

The 5869 Holdup Switch/Transmitter should be

programmed as a 24-hour silent zone type. Re er to the

Security System Control Panel Installation and Setup

Guide or programming instructions.

NOTES:

•During programming o the control panel, the 5869

Holdup Switch/Transmitter should be treated as "RF"

(i.e., supervised RF) Type.

•The 5869 is one closed input loop zone (loop 1).

MOUNTING

Mount the 5869 under a counter or money drawer or easy

access by the cashier. Re er to the igure and steps that

ollow or typical mounting installation.

Before mounting the 5869 permanently, perform Go/No Go

tests to verify adequate transmitter signal strength at desired

mounting location (refer to the ecurity ystem Control

Panel Installation and etup Guide).

1. Install the battery into the battery holder observing

correct polarity as shown in Figure 2.

2. Position the case to the desired location and install one

No. 6 x ¾ screw (supplied) at the breakaway tamper

release hole as shown in Figure 3.

3. Secure the cover to the case with the two screws (No 6 x

1/2) as shown in Figure 3.

IMPORTANT: To prevent damage to the case, do not

over tighten the cover screws.

4. Secure the case with the cover to its mounting location

using the two screws (No. 6 x 2) supplied as shown in

Figure 3.

5869-002-V1

MOUNTING

HOLE

(TYP.)

RESET

KEY

COVER

TAMPER

SWITCH

BREAKAWAY

TAMPER

SCREW

No. 6X3/4

COVER

3V

LITHIUM

BATTERY

COVER 

ATTACH

HOLE

COVER

ATTACH

HOLE

MOUNTING

SCREW (2)

No. 6X2



TRIGGER



ANTENNA

COVER

SCREW (2)

No. 6X1/2

COVER

SCREW (2)

No. 6X1/2

Figure 1. 5869 Holdup Switch/Transmitter Details

5869-006-V0

3V LITHIUM

BATTERY

TRIGGER

-

NOTE:

THE NEGATIVE (

)

SIDE OF THE BATTERY

MUST FACE THE TRIGGER

ANTENNA

Figure 2. 5869 Battery Installation

- 2 -

MOUNTING

HOLE

MOUNTING

HOLE

IMPORTANT:

THIS DEVICE MUST BE PERMANENTLY

MOUNTED WITH THE SCREWS SUPPLIED.

5869-004-V0

BREAKAWAY

TAMPER

SCREW

No. 6X3/4

MOUNTING

SCREW (2)

No. 6X2



MOUNTING

SCREW (2)

No. 6X2

COVER

SCREW (2)

No. 6x1/2

COVER

SCREW (2)

No. 6x1/2

Figure 3. Typical Holdup Switch Installation

BATTERY REPLACEMENT

BATTERY CAUTION:

Risk of fire, explosion, and burns. Do not recharge, disas-

semble, heat above 100°C, or incinerate. Dispose of used

batteries promptly and properly. Keep away from children.

IMPORTANT: When servicing the device or battery

replacement, note that with the mounting screws

removed the case is held in place by the tamper release

tab. Exercise caution not to jar the case while replacing

the battery, possibly breaking the Tamper breakaway

tab.

1. Remove the two screws securing the cover and two

mounting screws as shown in igure 1.

NOTE: Use care not to bend the antenna while

attempting to remove or install the battery.

2. Remove aulty battery and dispose o properly.

3. Observing correct polarity (negative side o the battery

acing the trigger), insert the battery into the battery

holder as shown in Figure 1.

4. Reinstall two cover screws and two mounting screws as

shown in Figure 1.

SPECIFICATIONS

Physical 1-15/16"W x 5-15/16"H x 1-3/16"D

(50mm x 150mm x 30mm)

Battery 3-volt Lithium. ADEMCO 466, Duracell

DL123A, Panasonic CR123A, or HUIDERUI

CR123A.

Frequency 345MHz

Reset Key: Supplied, Part Number K4563 to order

separately

Agency: UL 636 – Holdup alarm units and systems

CUS

LISTED

Note: Constant ex osure to high or low tem erature or high humidity may reduce battery life.

TO THE INSTALLER

Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are

vital to continuous satisfactory operation of any alarm system.

The installer should assume the responsibility of developing and offering a regular maintenance program to

the user, as well as acquainting the user with the proper operation and limitations of the alarm system and its

component parts. Recommendations must be included for a specific program of frequent testing (at least

weekly) to insure the system's operation at all times.

- 3 -

FEDERAL COMMUNICATIONS COMMISSION STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.

Unauthorized changes or modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for

your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the

manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the

limits for a Class computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•If using an indoor antenna, have a quality outdoor antenna installed.

•Reorient the receiving antenna until interference is reduced or eliminated.

•Move the radio or television receiver away from the receiver/control.

•Move the antenna leads away from any wire runs to the receiver/control.

•Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

•Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe est conforme à la norme NM -003 du Canada.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may

cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux

conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y

compris les interférences causant une réception indésirable.

ÊK5299V4%Š

K5299V4 2/10 Rev. B

SUPPORT & WARRANTY

For the latest documentation and online support information, please go to:

https://mywebtech.honeywell.com/

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa.

For patent information, see www.honeywell.com/patents

MyWebTech

Warranty

Patents

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

Tabla de contenidos

Otros manuales de Transmisor de Honeywell

Honeywell

Honeywell XNX-AM Series Manual de usuario

Honeywell

Honeywell ADEMCO 5804 Instrucciones de montaje

Honeywell

Honeywell STT750 SmartLine Manual de usuario

Honeywell

Honeywell 5802mn - Ademco Wireless Emergency... Manual de usuario

Honeywell

Honeywell ADEMCO 5820L Instrucciones de montaje

Honeywell

Honeywell STT700 SmartLine Guía del usuario

Honeywell

Honeywell ZR530 Manual de usuario

Honeywell

Honeywell oneWireless XYR 6000 Manual de usuario

Honeywell

Honeywell 5834-4EN Manual de usuario

Honeywell

Honeywell NOTIFIER UDACT-2 Manual de usuario

Honeywell

Honeywell 5815 - Ademco - Wireless Door Manual de usuario

Honeywell

Honeywell XNX Universal Transmitter Manual de usuario

Honeywell

Honeywell STT850 SMARTLINE Manual de usuario

Honeywell

Honeywell MCE 2 Manual de usuario

Honeywell

Honeywell oneWireless XYR 6000 Manual de usuario

Honeywell

Honeywell XNX Guía del usuario

Honeywell

Honeywell ST 3000 Manual de usuario

Honeywell

Honeywell STT700 STT700 Manual de usuario

Honeywell

Honeywell ST 800 Series Manual de usuario

Honeywell

Honeywell ADEMCO 5818MNL Instrucciones de montaje

Honeywell

Honeywell STT850 SMARTLINE Manual de usuario

Honeywell

Honeywell 5802mn2 - Ademco Wireless Panic Instrucciones de montaje

Honeywell

Honeywell XNX Manual de usuario

Honeywell

Honeywell SMV800 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manual de usuario