Honeywell DirectLine DL424 Manual de usuario

DirectLine®DL424/425 Sensor Module

for DL 5000 Dissolved Oxygen Probes

User Manual

70-82-25-113

Rev. 3

September 2011

Honeywell Process Solutions

Notices and Trademarks

September, 2011

Warranty/Remedy

Honeywell warrants goods of its manufacture as being free of defective materials and faulty

workmanship. Contact your local sales office for warranty information. If warranted goods

are returned to Honeywell during the period of coverage, Honeywell will repair or replace

without charge those items it finds defective. The foregoing is Buyer's sole remedy and is in

lieu of all other warranties, expressed or implied, including those of merchantability

and fitness for a particular purpose. Specifications may change without notice. The

information we supply is believed to be accurate and reliable as of this printing. However, we

assume no responsibility for its use.

While we provide application assistance personally, through our literature and the Honeywell

web site, it is up to the customer to determine the suitability of the product in the application.

CE Conformity

This product is in conformance with the protection requirements of the following European

Council Directives: 89/336/EEC, the Electromagnetic Compatibility Directive and

73/23/EEC, the Low Voltage Directive. Conformance of this product with any other “CE

Mark” Directive(s) shall not be assumed.

ATTENTION

The emission limits of EN 61326 are designed to provide reasonable protection against

harmful interference when this equipment is operated in an industrial environment. Operation

of this equipment in a residential area may cause harmful interference. This equipment

generates, uses and can radiate radio frequency energy and may cause interference to radio

and television reception when the equipment is used closer than 30 m to the antenna(e). In

special cases, when highly susceptible apparatus is used in close proximity, the user may

have to employ additional mitigating measures to further reduce the electromagnetic

emissions of this equipment.

Honeywell Process Solutions

Honeywell

512 Virginia Drive

Fort Washington, PA 19034

DirectLine is a trademark of Honeywell

Other brands or product names are trademarks of their respective owners

ii DirectLine® DL424/425 Sensor Module User Manual 9/11

About This Document

Abstract

This manual contains all the information that is needed to install, configure, calibrate,

operate, and troubleshoot the DirectLine®Sensor. Insert 70-82-10-04, a quick

reference guide for configuring and calibrating the DL424/425, should accompany

this document.

Contacts

World Wide Web

The following lists Honeywell’s World Wide Web sites that will be of interest to our

customers.

Honeywell Organization WWW Address (URL)

Corporate http://www.honeywell.com

Honeywell Process Solutions https://www.honeywellprocess.com

Telephone

Organization Phone Number

United States and

Canada Honeywell 1-800-423-9883 Tech. Support

1-888-423-9883 Q&A Faxback

(TACFACS)

1-800-525-7439 Service

Symbol Definitions

The following table lists any symbols used in this document to denote certain

conditions.

Symbol Definition

Earth Ground. Functional earth connection. NOTE: This connection shall

be bonded to Protective earth at the source of supply in accordance with

national and local electrical code requirements.

9/11 DirectLine® DL424/425 Sensor Module User Manual iii

Contents

1. INTRODUCTION....................................................................................................................1

1.1 Overview.........................................................................................................................................1

1.2 Electronics Module .........................................................................................................................2

1.3 Operator Interface...........................................................................................................................2

1.4 Specifications..................................................................................................................................3

1.5 Model Selection Guide ...................................................................................................................4

2. INSTALLATION.....................................................................................................................5

2.1 Assembly and Wiring......................................................................................................................5

2.2 Integral Mounting............................................................................................................................7

2.3 Remote Mounting ...........................................................................................................................8

2.4 Conduit connections.....................................................................................................................12

3. CONFIGURATION...............................................................................................................13

3.1 Overview.......................................................................................................................................13

3.2 Configuration Set Up Procedure...................................................................................................15

4. CALIBRATION.....................................................................................................................19

4.1 New Probe....................................................................................................................................19

4.2 Calibration Options.......................................................................................................................19

4.3 Calibration Procedures.................................................................................................................20

5. OPERATION........................................................................................................................22

5.1 Displays........................................................................................................................................22

5.2 Diagnostic Error Messages ..........................................................................................................24

5.3 Unit Reset.....................................................................................................................................26

6. SPARE PARTS....................................................................................................................27

7. APPENDIX: CE MARK APPLICATIONS ............................................................................29

8. SALES AND SERVICE........................................................................................................30

iv DirectLine® DL424/425 Sensor Module User Manual 9/11

Tables

Table 2-1 Assembly and Wiring Procedure for Field Wiring Connector__________________________ 6

Table 2-2 Integral Mounting Procedure (refer to Figure 2-3)__________________________________ 7

Table 2-3 Remote Mounting Procedure for DL5000 Probes __________________________________ 8

Table 2-4 Dissolved Oxygen Probes Remote Connections__________________________________ 10

Table 3-1 Dependence of Barometric Pressure on Altitude__________________________________ 13

Table 3-2 Configuration Set Up Procedure ______________________________________________ 15

Table 4-1 Calibration Procedure ______________________________________________________ 20

Table 5-1 Online Parameter Descriptions _______________________________________________ 22

Table 5-2 Display Navigation Procedure ________________________________________________ 23

Table 5-3 Online Diagnostic Errors ____________________________________________________ 24

Table 5-4 Factory Default Values _____________________________________________________ 26

9/11 DirectLine® DL424/425 Sensor Module User Manual v

vi DirectLine® DL424/425 Sensor Module User Manual 9/11

Figures

Figure 1-1 DirectLine® Sensor ________________________________________________________ 1

Figure 1-2 Electronics Module_________________________________________________________ 2

Figure 2-1 Cordset Connection and Wiring _______________________________________________ 5

Figure 2-2 Field Wiring Connector______________________________________________________ 6

Figure 2-3 Integral Mounting __________________________________________________________ 7

Figure 2-4 Remote Mounting__________________________________________________________ 9

Figure 2-5 Remote Mounting Hardware_________________________________________________ 11

Introduction

1. Introduction

1.1 Overview

The DirectLine® Sensor for dissolved oxygen measurement in water consists of a

DL424/425 electronics module connected to a DL5000 DO Probe. The modular

electronics design allows the module to be separated from the probe, so that the

probe can be easily removed or replaced while retaining power to the electronics

module.

The DL424/425 electronics module is contained in a Nema Type 4x sealed

weatherproof corrosion/impact-resistant polysulfone housing. The Module can be

mounted as an integral unit directly connected to the probe or remotely using a

probe with a cable. The sealed plastic housing has plug-in connections for the

DL5000 probe and a 4-20 mA output connection.

Figure 1-1 DirectLine® Sensor

9/11 DirectLine® DL424/425 Sensor Module User Manual 1

Introduction

1.2 Electronics Module

The electronics module is loop-powered by 16-42 Vdc and will modulate its supply

current from 4 mA to 20 mA, depending upon the DO value that is measured by the

probe. The transmitted loop current is compensated for process temperature.

A 4-20 mA output connection is provided via a 6m cordset or a customer supplied

cable used in combination with a field wiring connector.

The DirectLine ® electronic module for dissolved oxygen measurements is available

in two configurations:

ppm (DL424) and ppb (DL425).

Figure 1-2 Electronics Module

1.3 Operator Interface

The DirectLine® Sensor operator interface consists of three pushbuttons and one

4-digit, 7-segment LCD display with 3 decimal points, plus (+), and minus (–) signs.

It is responsible for the display of measured values and configuration of parameter

values.

2 DirectLine® DL424/425 Sensor Module User Manual 9/11

Introduction

1.4 Specifications

General:

Displayed Process

Variable DL424: 0-20 ppm dissolved oxygen

DL425: 0-200 ppb dissolved oxygen

Displayed

Temperature Range 2.0 to 60.0 ºC (35.6 to 140ºF)

Operating

Temperature –20 °C to +60 °C (-4 °F to +140 °F)

Storage Temperature –20 °C to +70 °C (-4 °F to +158 °F)

Display Resolution DL424: 0.01 ppm

DL425: 0.1 ppb in the 0-20 ppb range; 1 ppb in the

0-200 ppb range

Output Type 4-20 mA (2-wire loop powered)

Output Scale DL424: 0-20ppm

DL425: 0-200ppb

Output Calibration 4-20 mA

Power 16-42 Vdc

Maximum Load Resistance: 250 ohms at 16 Vdc

600 ohms at 24 Vdc

1400 ohms at 42 Vdc

Calibration Options Air Cal; Sample Cal

Diagnostics Sensor and electronics

Physical Properties:

Case Weatherproof, corrosion-resistant plastic housing

Local Display and

Buttons LCD 4-digit, 7-segment

Field Wiring Cordset Shielded twisted pair. Length: 6 m (19.7’)

User Termination Tinned leads

Remote Mounting Pipe, Wall, or DIN Rail

Dimensions H 123 mm (4.84”) x W 48 mm (1.89”) x D 46 mm (1.81”)

Weight Approximately 142 g (5.0 oz.)

Approvals CE Mark - Industrial Applications

UL – General Purpose

CSA – General Purpose

IP66 Enclosure

NEMA Type 4

FM Class1, Div. 1 (I.S.)

FM Class 1, Div. 2 (non-incendive field wiring)

9/11 DirectLine® DL424/425 Sensor Module User Manual 3

Introduction

1.5 Model Selection Guide

Instructions

Select the desired key number. The arrow to the right marks the selection available.

Make the desired selections from Tables I through IV using the column below the

proper arrow. A dot ( ) denotes availability.

Key Number I II III IV

_ _ _ _

Key Number - DirectLine

Sensor Electronics Module

(Specify electrodes/cells/probes separately) Selection

pH For use with Durafet II, Meredian II & HPW7000 pH electrodes DL421

ORP For use with ORP electrode. DL422

Conductivity For use with Contacting Conductivity Cells DL423

DO - PPM For use with Dissolved Oxygen ppm Probes DL424

DO - PPB For use with Dissolved Oxygen ppb Probes

TABLE I - OUTPUT CABLE

Cordset - 6m (19.7 ft.) - includes connector and cable - Note 2 E

Field Wiring Connector only - customer supplies cable only-Note 2

TABLE II - SENSOR CABLE/REMOTE CONNECTOR (between electronic module and electrode, sensor or pr

0ddddd

6,096m (20 ft.) of sensor cable - Durafet II Remote Mounting 1 e

15,24m

(

50 ft.

)

of sensor cable - Durafet II Remote Mountin

eeee

TABLE III - REMOTE MOUNTING OPTIONS

None Integral unit - mounting not required A

2" (5,08 cm) Pipe mtg. bracket, wall mtg, & DIN Rail clip B

TABLE IV - OPTIONSNone 00 _ _

Linen Customer ID Tag - 3 lines w/22 characters/line LT _ _

SS Customer ID Tag - 3 lines w/22 character/line SS _ _

Certificates None _ _ 00

Calibration & Conformance _ _ CC

Mounting Kit for

Remote Mounting

None(replacement module or customer supplied output cable)-Note 1 D

Remote Mounting Connector - Meredian II ORP

Remote Mounting Connector - HPW7000

Remote Mounting Connector - Conductivity

Remote Mounting Connector - Dissolved Oxygen

DL425

Remote Mounting Connector - Meredian II pH

Remote Mounting

Connector (Cable is

supplied with sensor or

probe)

Integral Mounting No cable or connector required

Remote Mounting Cable

- Durafet only

Availability

Output Cable for

Integral or Remote

Mounting F

_ _ _

Tagging

Notes:

1Customer supplies cordset o

cable with M12 connecter. Suppliers & P/Ns include:

Phoenix Contact Turck

Cord--set SAC-3P-5.0-PUR/M12FSSH Stainless RKV4T-6/S618

M12 Field Wiring Connector SACC-M12FS-4CON-PG7 B8141-0

Cable

2Recommended cable is 2-wire twisted shielded pair

RESTRICTIONS

Table

ORDERING INSTRUCTIONS:

1. Part numbers are provided to facilitate Distributor Stock.

2. Orders may be placed either by model selection or by part number.

3. Part numbers are shown within the model selection tables to assist with compatibility information.

4. Orders placed by model selection are systematically protected against incompatibility.

5. Compatibility assessment is the responsibility of the purchaser for orders placed by part number.

6. Items labeled as N/A are not available via the stocking program and must be ordered by model selection.

III B

Available OnlyWith Not Available With

IIl A

Selection Table

2-wire twisted shielded pair

Restriction

Letters Selection

4 DirectLine® DL424/425 Sensor Module User Manual 9/11

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Honeywell

Honeywell

Honeywell BCU 370 Manual

Honeywell

Honeywell S4560 Manual de usuario

Honeywell

Honeywell Pro-Watch 6000 Manual de usuario

Honeywell

Honeywell NetAXS-123 Manual de usuario

Honeywell

Honeywell VR8305 Manual de usuario

Honeywell

Honeywell Galaxy 2 Series Manual de usuario

Honeywell

Honeywell EXCEL 12 W7704B1002 Manual de usuario

Honeywell

Honeywell REDLINK ERM5220R Manual de operación

Honeywell

Honeywell EXCEL CARE 5000 Manual de usuario

Honeywell

Honeywell NK298S Manual de usuario

Honeywell

Honeywell 010690.02 Manual de instrucciones

Honeywell

Honeywell Notifier FCM-1-REL Manual de usuario

Honeywell

Honeywell V4730C Manual de usuario

Honeywell

Honeywell LYNX Series Manual de usuario

Honeywell

Honeywell MCV2000AA Instrucciones de instalación

Honeywell

Honeywell BCU 460 Manual

Honeywell

Honeywell TR80UWD Guía de instalación

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell L4068 Manual de usuario

Honeywell

Honeywell S8600A Manual de usuario

Honeywell

Honeywell V1810 Alwa-Kombi-4 Manual de usuario

Honeywell

Honeywell RV284 Manual de usuario

Honeywell

Honeywell NOTIFIER FCM-1A Manual de usuario

Honeywell

Honeywell MI-DCZME Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario