Heath Zenith 7868 Manual de usuario
This chime requires 2 “C” alkaline batteries (not included). In typical use,
alkaline batteries will last up to one year.
Wireless Chime
© 2016 HeathCo LLC
Figure 2
Figure 1
WARNING: To prevent possible
SERIOUS INJURY or DEATH:
• NEVER allow small children near
batteries.
• If battery is swallowed, immediately
notify doctor.
This package includes (Style of door sensor and chime may vary from illustration):
1. Remove orange battery tab from push
button. Remove back of case by pushing in
tab on bottom with a small screwdriver (see
Figure 1). Remove orange battery tab.
2. Remove chime cover. Firmly pull on cover
to remove it from chime base (see Figure 2).
Chime
base
Chime cover Wireless push
button
Hardware
pack
Model
TYPE'C'
LR14
TYPE'C'
LR14
MODEL:WL-102D
UP
SYNC– HOLD 3 SECONDS
RESET– HOLD 10 SECONDS
7868 ✔ ✔ ✔ ✔
7870 ✔ ✔ ✔ ✔
7871 ✔ ✔ ✔ ✔
TR-0095-RX
TYPE
C
2
TR-0095-RX
Battery Cover
Battery Cover Catch
TYPE 'C'
LR14
TYPE 'C'
LR14
MODEL: WL-102D
UP
SYNC – HOLD 3 SECONDS
RESET – HOLD 10 SECONDS
3. Install 2 alkaline “C” batteries. Press in
catch on bottom of battery cover and lift to
remove (see Figure 3). Make sure batteries
are oriented properly (see Figure 4).
4.
Test range. Temporarily position chime and
push button where you want them mounted.
Press push button to verify chime and push
button work properly. If chime does not sound,
see Troubleshooting.
5. Mount push button. Use either screws or
double sided tape to mount push button.
• Screw Mounting: To mount with screws,
remove back of case by pushing in tab on
bottom with a small screwdriver (see Figure
1). Note: Remove material in screw holes
(if needed) before mounting with screws.
Attach back of case to door jamb or wall (see
Figure 5). Snap front of push button on.
• Tape Mounting: When attaching push but-
ton using double sided tape, make sure the
surface of the door jamb or wall is clean.
6. Mount chime base. Determine mounting
location.
• Place chime against wall and verify the
chime is level. Note: See chime base for
correct orientation.
• Use all 4 chime mounting holes as a tem-
plate (see Figure 6).
• Drill 7/32" diameter pilot holes for wall an-
chors (provided) and insert anchors. Note:
Always use wall anchors if not mounting
directly into a stud.
• Verify chime is level and tighten screws
securely.
• Press chime cover onto chime base.
Figure 3
Figure 4
Figure 5
Figure 6
TR-0095-RX
TYPE
C
3
Inside Push Button
Tune Settings
Push Button Tune
Jumper - ON Ding
Jumper - OFF Ding-Dong
Tune Setting Table
The chime has different selectable tunes: Ding
(one note tune) or Ding-Dong (two note tune).
The factory setting is for the Ding-Dong tune.This
tune can be changed by following the instructions
in the Tune Setting Table.
Note: All chime models are designed to work with
up to 5 push buttons (sold separately).All chimes
are designed to play only two different tunes no
matter how many push buttons are used.
Troubleshooting
1. PROBLEM: Chime does not sound.
A. POSSIBLE CAUSE: Batteries not installed correctly.
A. CORRECTIVE ACTION: Make sure batteries are installed according to
the diagram inside the push button and chime.
B. POSSIBLE CAUSE: Batteries are dead.
B. CORRECTIVE ACTION: Check charge of push button and chime bat-
teries and replace if necessary.
C. POSSIBLE CAUSE: Push button and chime are not synced.
C. CORRECTIVE ACTION: Sync the push button and chime.
• Press and hold the button on the chime until the chime sounds a
“Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a
“Beep-Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
4
2. PROBLEM: Batteries seem okay, but the chime does not work after instal-
lation.
A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near
metal studs. Note: Metal reduces transmission range.
A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims
to move chime or push button away from metal surface.
B. POSSIBLE CAUSE: Chime is mounted near concrete floor or wall.Note:
Concrete may reduce range.
B. CORRECTIVE ACTION: Move chime away from concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate chime closer to push button.
3. PROBLEM: Chime sounds when not intended (false triggers).
POSSIBLE CAUSE: Chime is receiving interference from another wire-
less device.
CORRECTIVE ACTION: Reset chime and push button.
• Remove push button batteries. Wait 30 seconds.
• Press and hold the push button for 10 to 15 seconds within 60 seconds
after installing battery into the push button.
• Press and hold the button on the chime until the chime sounds a
“Beep-Beep-Beep-Beep”.
• To re-sync the push button and chime, press and hold the button on
the chime until the chime sounds a “Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a
“Beep-Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
Note: The push button and chime come synced from the factory. The range of
the wireless chime can vary with location, temperature, and battery condition.
TYPE 'C'
LR14
TYPE 'C'
LR14
MODEL: WL-102D
UP
SYNC – HOLD 3 SECONDS
RESET – HOLD 10 SECONDS
Learn more about home shop we have.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Accesorios de Heath Zenith
Heath Zenith
Heath Zenith 121AC Manual de usuario
Heath Zenith
Heath Zenith SL-6164 Manual de usuario
Heath Zenith
Heath Zenith Wireless Chime 6153/62/71/72 Manual de usuario
Heath Zenith
Heath Zenith 6180 Series Manual de usuario
Heath Zenith
Heath Zenith SL-6153 Manual de usuario
Heath Zenith
Heath Zenith SL-7464-03 Manual de usuario
Heath Zenith
Heath Zenith 7776 Manual de usuario
Heath Zenith
Heath Zenith Replacement Motion Sensor SH-5407 Manual de usuario
Heath Zenith
Heath Zenith SL-6200 Manual de usuario
Heath Zenith
Heath Zenith SL-6155 Series Manual de usuario
Heath Zenith
Heath Zenith Single Entrance Chime 23/M Manual de usuario
Heath Zenith
Heath Zenith 7750 Manual de usuario
Heath Zenith
Heath Zenith Replacement Motion Sensor SL-5407 Manual de usuario
Heath Zenith
Heath Zenith 121AC Manual de usuario
Heath Zenith
Heath Zenith Motion Sensing 3-Way Wall Switch 6107 Manual de usuario
Heath Zenith
Heath Zenith 6180 Series Manual de usuario
Heath Zenith
Heath Zenith Notifi elite Manual de usuario
Heath Zenith
Heath Zenith InTune MP3 Door Chime Manual de usuario
Heath Zenith
Heath Zenith DualBrite Manual de usuario
Heath Zenith
Heath Zenith Wireless Mechanical Battery Operated Chime... Manual de usuario
