Heath Zenith 7311 Manual de usuario

Wireless Chime

1. Remove orange battery tab from push button.

Remove back of case by pushing in tab on bottom

with a small screwdriver (see Figure 1). Remove

orange battery tab.

2. Plug in wireless chime (see Figure 2).

3. Test range. Temporarily position chime and push

button where you want them mounted. Press push

button to verify chime and push button work prop-

erly. If chime does not sound, see Troubleshooting.

Figure 1

Figure 2

WARNING:To prevent possible SERIOUS

INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify

doctor.

This package includes (Style of push button and chime may vary from illustration):

Model

Wireless

chime

VOL+VOL–Light Sync

Music

Wireless push

button Hardware

pack

7311 ✔ ✔ ✔

VOL+VOL–Light Sync

Music

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

4. Mount push button. Use either screws or double

sided tape to mount push button.

•

Screw Mounting: To mount with screws, remove

back of case by pushing in tab on bottom with a

small screwdriver (see Figure 1). Note: Remove

material in screw holes (if needed) before mounting

with screws. Attach back of case to door jamb or

wall (see Figure 3). Snap front of push button on.

• Tape Mounting: When attaching push button

using double sided tape, make sure the surface

of the door jamb or wall is clean.

Operation

Chime Mute

The chime can be muted for a select period of time:

full-time, 3 hours, 6 hours, 9 hours, or 12 hours. Press

and release the mute icon to select the amount of time

the chime should be muted (see Figure 4). The mute

icon will turn green each time it is pressed to show the

amount of time selected.

Figure 4

Figure 3

OFF Full-Time 3Hr 6Hr 9Hr 12Hr

Note: The chime will ﬂash the selected color each

time the push button is pressed whether the chime is

muted or unmuted.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Tune Setting Table

Push Button Tune

Switch 2 - ON (Back Door) Ding

Switch 2 - OFF (Front Door) Selected Musical Tune

Volume Control

The chime has adjustable volume levels. Press and

release the “VOL +” or “VOL –” buttons to increase or

decrease the chime volume.

Light Color Selection

The chime will blink whenever the push button is

pressed.The color of the light is selectable. Press and

hold the “Light” button until the chime glows.While the

chime is glowing, press and release the “Light” button

to select the desired color. Press the push button to

lock in the desired color.

Tune Selection

The chime has ten pre-loaded selectable “front door”

tunes. Press and release the “Sync/Music” button until

the desired tune is heard.While the desired tune is play-

ing, press the push button to lock in the selected tune.

Note: Each push button can be assigned its own

unique tune.

Note: To listen to the selected tune, press and release

the “Sync/Music” button.

Note: All chime models are designed to work with up

to 5 push buttons (sold separately).

VOL +VOL –Light Sync

Music

VOL +VOL –Light Sync

Music

VOL +VOL –Light Sync

Music

Tune Selection Guide

Front Door

Ding-Dong Birthday Celebration

Traditional Westminster Auld Lang Syne

Traditional Whittington Beethoven’s 5th

Bell Whittington We Wish You a Merry Christmas

Short Westminster Star Spangled Banner

Back Door

Ding

1 2

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Troubleshooting

1. PROBLEM: Chime does not sound or rang one time and quit.

A. POSSIBLE CAUSE: Push button and chime are not synced.

A. CORRECTIVE ACTION: Sync the push button and chime.

• Press and hold the “Sync/Music”button on the chime until the chime sounds

a “Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a “Beep-

Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

B. POSSIBLE CAUSE: Push button battery is not installed correctly.

B. CORRECTIVE ACTION: Make sure battery is installed according to the

diagram inside the push button.

C. POSSIBLE CAUSE: Push button battery is dead.

C. CORRECTIVE ACTION: Check charge of push button battery and replace if

necessary.

D. POSSIBLE CAUSE: Chime is not receiving power.

D. CORRECTIVE ACTION: Make sure the plug-in chime has power.

E. POSSIBLE CAUSE: Chime is muted.

E. CORRECTIVE ACTION: Press and release the mute button until the green

light is turned off.

F. POSSIBLE CAUSE: Dip switch #1 in the push button has been moved to the

“ON” position.

F. CORRECTIVE ACTION: Ensure dip switch #1 is in the “OFF” position in the

push button and follow the steps above to re-sync the push button and chime.

2. PROBLEM: Push button battery seems okay, but the chime does not work after

installation.

A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near metal

studs. Note: Metal reduces transmission range.

A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to

move push button away from metal surface. Move chime to a different wall

outlet.

B. POSSIBLE CAUSE: Chime is mounted near concrete ﬂoor or wall. Note:

Concrete may reduce range.

B. CORRECTIVE ACTION: Move chime away from concrete surface.

C. POSSIBLE CAUSE: Chime and push button are installed too far apart.

C. CORRECTIVE ACTION: Locate chime closer to push button.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

3. PROBLEM: Chime sounds when not intended (false triggers).

POSSIBLE CAUSE: Chime is receiving interference from another wireless

device.

CORRECTIVE ACTION: Reset chime and push button.

• Remove push button battery. Wait 30 seconds.

• Press and hold the push button for 10 to 15 seconds within 60 seconds

after installing battery into the push button.

• Press and hold the “Sync/Music”button on the chime until the chime sounds

a “Beep-Beep-Beep-Beep”.

• To re-sync the push button and chime, press and hold the “Sync/Music”

button on the chime until the chime sounds a “Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a “Beep-

Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

4. PROBLEM: The new push button and chime do not work with existing push

buttons and chimes.

POSSIBLE CAUSE: The new push button and chime are not using the same

codes as existing push buttons and chimes.

CORRECTIVE ACTION: The new push button and chime need to be set

to work with existing push buttons and chimes. Please call 1-800-858-8501

for assistance in changing the codes to work with existing push buttons and

chimes.

Note: The push button and chime come synced from the factory. The range of the

wireless chime can vary with location, temperature, and battery condition.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Please contact us for assistance

before returning product to the

store or to HeathCo LLC.

If you experience a problem, follow this

guide.You may also contact us between

8:00 AM to 5:00 PM CST (M-F).

When contacting Technical Service,

please include the following informa-

tion: Name, Street Address, Daytime

Phone Number, Email Address, Model

Number, Date of Purchase, Place of

Purchase, Product Issue, and DATED

SALES RECEIPT FOR WARRANTY

REQUESTS.

Technical Service

No Service Parts Available for this

Product

HeathCo LLC

P.O. Box 90045

2445 Nashville Road

Bowling Green, KY 42101, USA

ATTN: Technical Service

Internet: www.hzsupport.com

Phone: 1-800-858-8501 (English Only)

Fax: 1-270-846-8500

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

HeathCo LLC reserves the right to discontinue and to change speciﬁcations at any

time without notice without incurring any obligation to incorporate new features in

previously sold products.

ONE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights. You may

also have other rights which vary from state to state or province to province.

For a period of one year from the date of purchase, any malfunction caused by

factory defective parts or workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, light bulbs, batteries, and other expendable items are

not covered by this warranty. Any damage to the light ﬁxture resulting from the

use of chemicals or a pressure washer machine are not covered by this war-

ranty. Unauthorized service or modiﬁcation of the product or of any furnished

component will void this warranty in its entirety. This warranty does not include

reimbursement for inconvenience, installation, setup time, loss of use, unauthor-

ized service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not extended

to other equipment and components that a customer uses in conjunction with

our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION

OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT

FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF

ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUS-

TOMER ANDTHERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO

LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS

OR PROFITS,WHETHER OR NOT FORESEEABLE.Some states or provinces

do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation or exclusion may not apply to you.

Please keep your dated sales receipt,it is required for all warranty requests.

Campana Inalámbrica

1. Retire la pestaña naranja de la batería del botón

pulsador. Extraer la parte posterior de la caja pre-

sionando la aleta en el botón con un destornillador

pequeño (vea la Figura 1).Quite la aleta anaranjada

de la batería.

2. Campana inalámbrica enchufable (vea la

Figura 2).

3. Pruebe el alcance. Ponga provisionalmente la

campana y el pulsador en la posición donde los

quiera instalar. Presione el pulsador para veriﬁcar

que la campana y el pulsador funcionen apropia-

damente. Si la campana no suena, vea Análisis de

Averías.

ADVERTENCIA: Para prevenir una posible

LESIÓN SERIA o LA MUERTE:

• NUNCA deje que los niños estén cerca de las

baterías.

• Si se traga una batería, notiﬁque inmediata-

mente al doctor.

Este paquete tiene (El estilo del pulsador y de la campana puede variar de la

ilustración):

Figura 1

Figura 2

Model

Wireless

chime

VOL+VOL–Light Sync

Music

Wireless push

button Hardware

pack

7311 ✔ ✔ ✔

VOL+VOL–Light Sync

Music

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Figura 3

4. Instale el pulsador. Use ya sean tornillos o cinta

adhesiva por ambas caras para instalar el pulsador.

• Montaje con tornillos: Para montar con tornillos,

quite la parte de atrás de la caja empujando

hacia adentro la lengüeta de abajo con un

destornillador pequeño y girando la cuchilla

(vea la Figura 1). Nota: Quite la suciedad de los

oriﬁcios para tornillos (si es necesario) antes de

poner los tornillos. Coloque la parte de atrás de la

caja contra la jamba o la pared (vea la Figura 3).

Encaje a presión la parte frontal del pulsador.

• Montaje con cinta adhesiva: Cuando ﬁje el

pulsador usando cinta adhesiva por ambas caras,

asegúrese que la superﬁcie de la pared o la del

batiente de la puerta estén limpias.

Operación

Silenciador del timbre

La campana puede ser puesta en silencio por un

período de tiempo seleccionado: tiempo completo, 3

horas, 6 horas, 9 horas o 12 horas. Presione y suelte

el icono de silencio para seleccionar la cantidad de

tiempo que la campana debe estar puesta en silencio

(vea la Figura 4). El icono de silencio se volverá color

verde cada vez que se lo presiona para mostrar la

cantidad de tiempo seleccionada.

Figura 4

OFF Full-Time 3Hr 6Hr 9Hr 12Hr

Nota: La campana parpadeará el color seleccionado

cada vez que se presione el pulsador sea que la

campana esté o no puesta en silencio.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Tabla de programación de melodías

Botón pulsador Ajustes

Interruptor 2 - ENCENDIDO (Puerta posterior) Ding

Interruptor 2 - APAGADO (Puerta principal) Melodía musical seleccionada

Control del volumen

La campana tiene niveles de volumen regulables

Presione y suelte los botones “VOL +” o “VOL –” para

aumentar o disminuir el volumen de la campana.

Selección del color de la luz

La campana parpadeará cada vez que se presione el

pulsador.El color de la luz es seleccionable.Presione

y mantenga presionado el botón “Light” [“luz”] hasta

que la campana se ilumine. Mientras la campana

está iluminada presione y suelte el botón “Light” para

seleccionar el color deseado.Presione el pulsador para

ﬁjar el color deseado.

Selección de tono

La campana tiene diez melodías para la “puerta

principal” seleccionables precargadas. Presione y

suelte el botón “Sync/Music”hasta escuchar la melodía

deseada. Mientras se reproduce la melodía deseada,

presione el pulsador para ﬁjar la melodía seleccionada.

Nota: A cada pulsador se le puede asignar su propia

y única melodía.

Nota: Para escuchar la melodía seleccionada, presione

y suelte el botón “Sync/Music”[“Sincronizar / Música”].

Nota: Todos los modelos de campanillas están dise-

ñados para trabajar hasta con 5 botones pulsadores

(se venden por separado).

VOL +VOL –Light Sync

Music

VOL +VOL –Light Sync

Music

VOL +VOL –Light Sync

Music

Guía de Selección de Tonos

Puerta del frente

Ding-Dong Birthday Celebration

Traditional Westminster Auld Lang Syne

Traditional Whittington Beethoven’s 5th

Bell Whittington We Wish You a Merry Christmas

Short Westminster Star Spangled Banner

Puerta de atrás

Ding

1 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios de Heath Zenith

Heath Zenith

Heath Zenith 5316 Manual de usuario

Heath Zenith

Heath Zenith 3106978 (AC-6196) Manual de usuario

Heath Zenith

Heath Zenith SECUR360 9600 Manual de usuario

Heath Zenith

Heath Zenith Hardwired Electronic Chime 598-1113-05 Manual de usuario

Heath Zenith

Heath Zenith Secure Home 5215 Manual de usuario

Heath Zenith

Heath Zenith SL-6168 Manual de usuario

Heath Zenith

Heath Zenith Lighted Wireless Push Button Accessory Manual de usuario

Heath Zenith

Heath Zenith 595-5684-09 Manual de usuario

Heath Zenith

Heath Zenith InTune MP3 Door Chime Manual de usuario

Heath Zenith

Heath Zenith 7309 Manual de usuario

Heath Zenith

Heath Zenith Wireless Chime 6153/62/71/72 Manual de usuario

Heath Zenith

Heath Zenith Wireless Christmas Chime 598-1127-03 Manual de usuario

Heath Zenith

Heath Zenith Notif Manual de usuario

Heath Zenith

Heath Zenith 7776 Manual de usuario

Heath Zenith

Heath Zenith Wireless Push Button Accessory SL-6190... Manual de usuario

Heath Zenith

Heath Zenith Wireless Chime 598-1172-04 Manual de usuario

Heath Zenith

Heath Zenith 6168 Manual de usuario

Heath Zenith

Heath Zenith 598-1112-04 Manual de usuario

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1151-02 Manual de usuario

Heath Zenith

Heath Zenith 29 Manual de usuario

Heath Zenith

Heath Zenith 7868 Manual de usuario

Heath Zenith

Heath Zenith 5210 Manual de usuario

Heath Zenith

Heath Zenith 7797 Manual de usuario

Heath Zenith

Heath Zenith 7143 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario