Heath Zenith Wireless Dual Push Button Accessory SL-6200 Manual de usuario

Wireless Dual Push

Button Accessory

The Heath®/Zenith Wireless Push Button

Accessory works with existing Heath®/Zenith

jumper or dip switch systems.

• Battery powered push button - No wires to

run.

• 128 selectable codes allow more than one

chime system in the same house.

• Each button can be set to ring a different

chime or ring different tunes on the same

chime.

SL-6200

(Style may vary from illustration)

-2- 598-1144-02

1. Install alkaline type A23 12 volt push button battery.

Remove back of case by pushing in tab on bottom with a

small screwdriver. Make sure battery is oriented properly

(see page 5).

2. Set the push button jumpers for each button to match

the respective chime receiver code. See Code and Tune

Settings section.

3. Test range. Temporarily position push button where you

want it mounted. Press push button to verify chime and

push button work properly. If chime does not sound, see

Troubleshooting.

4. Mount push button. Use either screws or double sided

tape to mount push button.

• To mount with screws, remove back of case by pushing in

tab on bottom with a small screwdriver.Remove material

in screw hole. Attach back of case to door jamb or wall.

Snap front of push button on.

• When attaching push button using double sided tape,

make sure the surface of the door jamb or wall is clean.

Install This End

Down

Remove material

in screw hole

before mounting

with screws

-3-

598-1144-02

Code and Tune Settings

Code Settings

Note: The top button is factory set to our standard default

code (5, 6, 7).The bottom button is factory set to a different

code. Follow the instructions below to set the code and

tune for each chime. Verify the push button codes match

the respective chime code.

WARNING: Disconnect chime unit from power source

before opening code access door. Close door and replace

screw before reconnecting to power.

The push button and chime communicate by using a code that

can be changed by removing and/or adding jumpers on both the

push button and chime.The code is factory set; however, there

are 128 selectable codes that allow you to expand your system

and prevent outside interference. Other wireless products may

cause interference and the system may not function properly.

Follow the instructions below for setting a new code.

1. Unplug wireless chime (if applicable).

2. Open the cases and locate the jumpers on both the push

button and chime (See illustration on page 5).

3. The push button and chime both have eight different jumper

locations. The jumper positions 1 through 7 are used for

setting the code.

4. To change the code, add and/or remove jumpers as needed.

It is recommended to only change one jumper at a time and

then check to see if system is functioning properly.

Note: Jumpers in positions 1 through 7 must be exactly

the same for both the push button and chime for this

system to function.

-4- 598-1144-02

Tune Settings

Your Heath®/Zenith wireless chime has different selectable

tunes:Ding (one note), Ding-Dong (two note), or Westminster

(eight note) (Available on selected Heath®/Zenith chimes).

The factory setting is for the Ding-Dong tune (or Westminster,

when available). This tune can be changed by following the

instructions below.

• Ding (one note tune)

Push button: Add a jumper to location 8.

• Ding-Dong (two note tune)

Push button: Remove jumper from location 8.

Chime: Remove jumper from location 8.

• Westminster (Eight note tune) (Available on selected

Heath®/Zenith chimes)

Push button: Remove jumper from location 8.

Chime: Add a jumper to location 8.

Note: To ring different tunes on the same chime, do the

following:

1. Set the bottom button code to match the top button code on

the dual push button.

2. Set the chime code to match the push button codes.

3. Set the tune settings for the top and bottom buttons per the

instructions above.

We recommend the back door use the Ding tune and the front

door use the Ding-Dong tune (or Westminster tune, available

on selected Heath®/Zenith chimes).

-5-

598-1144-02

12345678 12345678

Remove screw

to open access

door

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

Top

Button Bottom

Button

TYPE: A23

Inside

Push Button

Push Button Battery

Replacement

Install an alkaline type A23

12 Volt battery. See diagram

inside push button for correct

battery orientation.

* Code Settings

1-7 Must Match

Each Push

Button to the

Respective

Chime

Tune

Setting

Code for Top Button

Code for

Bottom Button

Note: Some models might require

the use of tweezers to remove

and replace the jumpers.

Back of Chime

Set to Match

Top Button

Back of Chime

Set to Match

Bottom Button

Tune Setting

(Not used on

all models)

-6- 598-1144-02

Troubleshooting

Chime does not sound:

• Make sure push button and chime codes are the same (See

pages 3, 4, and 5).

• Check orientation of push button battery (See page 5).

• Check charge of push button and chime batteries (if ap-

plicable), replace if necessary.

Batteries seem OK, but the chime does not work when

installed:

• Do not mount chime or push button on metal or near metal

studs. This reduces the transmitter range. Use 1/4" to 1/2"

(6 to 13 mm) wood shims to move chime or push button off

metal surface.

• Concrete ﬂoors may reduce range. Move chime away from

ﬂoor.

• Try locating chime closer to push button.

The range of the wireless chime can vary with location, tem-

perature and battery condition.

Label Push Buttons

Using a small ﬂat head screw-

driver or ﬁngernail, carefully pry

off the label covers on the front

of the push button. Remove and

write relevant information on

labels. Replace label covers.

Label

Covers

Labels

-7-

598-1144-02

Regulatory Information

This device complies with Part 15 of the FCC Rules and RSS-

210 of Industry Canada.Operation is subject to the following two

conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received,

including interference that may cause undesired operation.

The user is cautioned that changes or modifications not

expressly approved by the party responsible for regula-

tory compliance could void the user’s authority to operate

the equipment.

Technical Service

Please call 1-800-858-8501 (English speaking only)

for assistance before returning product to store.

If you experience a problem, follow this guide.You may also want

to visit our Web site at: www.hzsupport.com. If the problem

persists, call* for assistance at 1-800-858-8501, 7:30 AM to

4:30 PM CST (M-F).You may also write* to:

HeathCo LLC

P.O. Box 90004, Bowling Green, KY 42102-9004

ATTN: Technical Service

* If contacting Technical Service, please have the following

information available: Model Number, Date of Purchase, and

Place of Purchase.

No Service Parts Available for this Product

-8- 598-1144-02

FIVE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights. You may also

have other rights which vary from state to state or province to province.

For a period of ﬁve years from the date of purchase, any malfunction

caused by factory defective parts or workmanship will be corrected at

no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, light bulbs, batteries, and other expendable items

are not covered by this warranty. Unauthorized service or modiﬁcation of

the product or of any furnished component will void this warranty in its

entirety.This warranty does not include reimbursement for inconvenience,

installation, setup time, loss of use, unauthorized service, or return

shipping charges.

This warranty covers only HeathCo LLC assembled products and is not

extended to other equipment and components that a customer uses in

conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY,

REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT

THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE,

AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL,

OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE

CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART

OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL,

OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED

TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT

FORESEEABLE. Some states or provinces do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. Please keep your dated sales receipt,

it is required for all warranty requests.

HeathCo LLC reserves the right to discontinue and to change speciﬁcations

at any time without notice without incurring any obligation to incorporate new

features in previously sold products.

-9-

Accesorio inalámbrico

del pulsador doble

El accesorio de pulsador inalámbrico Heath®/

Zenith funciona con el puente Heath®/Zenith

o con los sistemas de interruptores.

• Pulsador alimentado con pila – No se

necesitan alambres.

• Los 128 códigos elegibles permiten más

de un sistema de campanas en la misma

casa.

• Cada botón puede programarse para que

haga sonar una campana diferente o tonos

diferentes en la misma campana.

SL-6200

(El estilo puede variar de la ilustración)

-10- 598-1144-02

Instale con este

extremo abajo

Retire el material

del hueco del

tornillo antes

de colocar los

tornillos

1. Instalar pila alcalina de botón tipo A23 de 12 voltios.

Extraer la parte posterior de la caja presionando la aleta

en el botón con un destornillador pequeño. Asegurarse que

la pila esté orientada correctamente (ver la página 13).

2. Coloque los puentes del pulsador para que cada botón

empareje con el respectivo código del receptor de la

campana. Vea la sección de Programaciones del código y

del tono.

Pruebe el alcance. Ponga provisionalmente el pulsador en

la posición donde lo quiera instalar.Presione el pulsador para

veriﬁcar que la campanay el pulsador funcionen apropiada-

mente. Si la campana no suena, vea Análisis de Averías.

4. Instale el pulsador. Use ya sean tornillos o cinta adhesiva

por ambas caras para instalar el pulsador.

• Para montar con tornillos, quite la parte de atrás de la

caja empujando hacia adentro la lengüeta de abajo con

un destornillador pequeño y girando la cuchilla.Retire el

material del hueco del tornillo. Coloque la parte de atrás

de la caja contra la jamba o la pared. Encaje a presión

la parte frontal del pulsador.

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios de Heath Zenith

Heath Zenith

Heath Zenith SL-6143 Manual de usuario

Heath Zenith

Heath Zenith Wireless Chime 598-1172-04 Manual de usuario

Heath Zenith

Heath Zenith 7750 Manual de usuario

Heath Zenith

Heath Zenith 7143 Manual de usuario

Heath Zenith

Heath Zenith SECUR360 9600 Manual de usuario

Heath Zenith

Heath Zenith 7868 Manual de usuario

Heath Zenith

Heath Zenith Notif Manual de usuario

Heath Zenith

Heath Zenith SL-6155 Series Manual de usuario

Heath Zenith

Heath Zenith 6180 Series Manual de usuario

Heath Zenith

Heath Zenith Dual Brite SL-5597 Manual de usuario

Heath Zenith

Heath Zenith 598-1112-04 Manual de usuario

Heath Zenith

Heath Zenith Motion Sensor Entryway Light SL-5610/15 Manual de usuario

Heath Zenith

Heath Zenith Motion Sensing 3-Way Wall Switch 6107 Manual de usuario

Heath Zenith

Heath Zenith 7307 Manual de usuario

Heath Zenith

Heath Zenith Wireless Christmas Chime 598-1127-03 Manual de usuario

Heath Zenith

Heath Zenith 5316 Manual de usuario

Heath Zenith

Heath Zenith 7797 Manual de usuario

Heath Zenith

Heath Zenith Wireless Mechanical Battery Operated Chime... Manual de usuario

Heath Zenith

Heath Zenith 595-5707-06 Manual de usuario

Heath Zenith

Heath Zenith SL-6200 Manual de usuario

Heath Zenith

Heath Zenith 7309 Manual de usuario

Heath Zenith

Heath Zenith SL-6166 Manual de usuario

Heath Zenith

Heath Zenith Decorative Wireless Chime 598-1000-07 Manual de usuario

Heath Zenith

Heath Zenith DUAL BRITE SL-5597 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario