Heath Zenith 598-1112-04 Manual de usuario

P.O. Box 90004

Bowling Green, KY 42102-9004

Hardwired

Mechanical

Chime

-2- 598-1112-04

CHIME REPLACEMENT INSTALLATION

Note: Electrical work must be in accordance with national and local

electrical codes. If in doubt, consult a qualiﬁed electrician.

1. Verify transformer power rating. Power must be supplied from

a 16 Volt AC, 10 Watt or a 16 Volt AC, 15 Watt transformer

(Heath®/Zenith models 122C, 121AC, or 125C).

2. Remove cover from existing chime.

3. Labelallwiresbeforedisconnecting.Usingmaskingtape, mark

each wire according to existing chime terminal markings.

• “F” – Front Push Button Wire

• “T” – Transformer Wire

• “R” – Rear Push Button Wire*

4. Disconnect all wires from existing chime.

5. Remove existing chime base from wall.

6. Determine proper chime base orientation. The chime cover

style may determine orientation.

7. Determine cover mounting type. For hang pin and hole type

covers, hang pin should be installed before mounting base to

wall. Install hang pin by snapping into mounting hole or sliding

onto chime base, depending on type of hang pin (see Figures 1

and 3).

Illustrations may vary from actual chime unit.

Figure 1 - Mechanical Chime Identiﬁcation

(Model 35 Base Shown)

FRONT

REAR

TRANS

Hang Pin, Snap-On

Type (Used for Hang

Pin and Hole Covers)

Base Orientation

Marking

Wire Entrance Hole

Mounting Slot (x4)

Tone Bars

Transformer and

Push Button Wire

Connections

Continued

Plungers

Hang Pin Mounting

Slot (Horizontal)

Hang Pin Mounting

Slot (Vertical)

Hang Pin, Slide-On Type

(Used for Hang Pin and

Hole Covers)

-3- 598-1112-04

FRONT

REAR

TRANS

8. Route wires through wire entrance hole in new chime base.

9. Mount chime base to wall using screws provided.

10. Connectwire“F”toscrewterminalmarked“FRONT”.Connect

wire “T” to screw terminal marked “TRANS”. Connect wire

“R” to screw terminal marked “REAR”* (See Figure 2).

11. Install chime cover (see page 4).

*Note: Some installations may not include rear door push button.

Figure 2 - Mechanical Chime Wiring

(Model 35 Base Shown)

Existing Chime Wires

Wall

Replacement Chime Base Rear Door Push Button

(if Applicable)

-4- 598-1112-04

FRONT

REAR

TRANS

Figure 4 - Mounting Snap-On Cover

INSTALL CHIME COVER

Place chime cover securely over base.

• For hang pin and hole covers: Attach hang pin to base prior

to mounting base on wall. Line up hole in cover with pin and hang

(see Figure 3).

• For snap-on covers: Apply pressure to the cover until it snaps

into place (see Figure 4). Firmly grasp cover and pull to remove

from base.

• For hang bracket covers: Determine if the cover will hang

vertically or horizontally on the base. Place bracket into the cor-

rect slot inside chime cover.

Adjust bracket (if necessary) so that bracket is ﬂush with back

surface of cover. Slide bracket into slot on base to hang cover (see

Figure 5).

Note: Never use cleaners or polishes. Never use any ﬂuids on the

chime mechanism. Use dry cloth to clean chime cover and base.

FRONT

REAR

TRANS

Figure 3 - Pin for Hanging Cover

Hang Pin,

Snap-On Type

Illustrations may

vary from actual

chime unit.

Snap-On Cover

Base Orientation

Marking

Hang Pin, Slide-On Type

-5- 598-1112-04

FRONT

TRANS

Figure 5 - Mounting Hang Bracket Cover

Illustrations may vary from actual chime unit.

Hang Bracket

Cover

Base

Orientation

Marking

Hang Bracket

Chime Base

(Mounted Vertically)

Hang

Bracket Slot

-6- 598-1112-04

TROUBLESHOOTING

Chime does not sound:

• Check Chime: Disconnect wire from terminal marked “TRANS”. Have someone operate push button at front door while you mo-

mentarily touch the “TRANS” wire to terminal marked “FRONT”. You will see a small spark if push button, wiring, and transformer

are operating properly. Repeat the steps for “REAR” terminal and rear push button. If wiring between transformer and push button(s)

check out properly, replace chime.

• Check Transformer: Test transformer voltage output with a volt meter. If a volt meter is not available, momentarily touch the two

low-voltage terminals with a screwdriver.You will see a small spark if transformer is operating properly. If no spark is evident, replace

transformer.

• Check Push Button(s): Remove suspected push button from door frame, disconnect wire from terminals and touch bare wires

together. If chime operates, push button is defective. Replace push button.

-7- 598-1112-04

ONE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights. You may also have other rights which vary from state to state or province to province.

For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not

covered by this warranty. Unauthorized service or modiﬁcation of the product or of any furnished component will void this warranty in its entirety. This war-

ranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.

This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and components that a customer uses

in conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION

OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN

LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA

SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY

LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation or exclusion may not apply to you. Proof of purchase is required for warranty claims.

DESA Specialty Products™ reserves the right to discontinue and to change speciﬁcations at any time without notice without incurring any obligation to incorporate new

features in previously sold products.

TECHNICAL SERVICE

Please call 1-800-858-8501 for assistance before returning product to store.

If you experience a problem, follow this guide.You may also want to visit our Web site at: www.desatech.com. If the problem persists,

call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:

DESA Specialty Products™

ATTN: Technical Service Specialty Products

P.O. Box 90004, Bowling Green, KY 42102-9004

* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Pur-

chase.

No Service Parts Available for this Product

-8- 598-1112-04

FRONT

REAR

TRANS

Chime System Wiring Diagram

Transformer

Front Door

Push Button

Chime

Rear Door

Push Button

(If Applicable)

-9- 598-1112-04

P.O. Box 90004

Bowling Green, KY 42102-9004

Campana con

componentes

mecánicos

-10- 598-1112-04

INSTALACIÓN DEL REEMPLAZO DE LA

CAMPANA

Nota: El trabajo eléctrico debe estar conforme a los códigos eléc-

tricos nacionales y locales. Si tiene alguna duda consulte con un

electricista caliﬁcado.

1. Veriﬁque la potencia nominal del transformador. La energía

debe suministrarse desde un transformador de 16 voltios CA,

10 vatios ó uno de 16 voltios CA, 15 vatios (Heath®/Zenith

modelos 122C, 121AC ó 125C).

2. Retire la tapa de la campana instalada.

3. Antes de desconectar marque todos los conductores. Usando

cinta protectora, marque cada conductor de acuerdo a las marcas

del terminal de la campana.

• “F” – Conductor del pulsador frontal

• “T” – Conductor del transformador

• “R” – Conductor del pulsador posterior*

4. Desconecte todos los conductores de la campana instalada.

5. Retire de la pared la base de la campana instalada.

6. Determine la orientación correcta de la base de la campana. Es

estilo de la tapa de la campana puede determinar la orientación.

7. Determine el tipo de montaje de la tapa. En tapas tipo clavija y

tipo oriﬁcio, la clavija de colgar debe instalarse antes de colo-

car la base a la pared. Instale la clavija de colgar insertándola

a presión en el oriﬁcio de montaje o deslizándola sobre la base

de la campana, dependiendo del tipo de clavija de colgar (vea

las Figuras 1 y 3).

Las ilustraciones pueden variar de la unidad de campana real.

Continúa

Figura 1 - Identiﬁcación de la campana mecánica

(Se muestra la base del modelo 35)

FRONT

REAR

TRANS

Clavija de colgar, tipo a

presión (usada para tapas

tipo clavija y tipo oriﬁcio)

Marca de orientación

de la base

Oriﬁcio de entrada

del cable

Ranura de montaje (x4)

Barras del tonos

Conexiones del

conductor del

transformador y

pulsador

Émbolos

Ranura de montaje para la

clavija de colgar (horizontal)

Ranura de montaje

para la clavija de

colgar (vertical)

Clavija de colgar, tipo des-

lizante (usada para tapas

tipo clavija y tipo oriﬁcio)

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios de Heath Zenith

Heath Zenith

Heath Zenith DualBrite Manual de usuario

Heath Zenith

Heath Zenith 7306 Manual de usuario

Heath Zenith

Heath Zenith Replacement Motion Sensor SH-5407 Manual de usuario

Heath Zenith

Heath Zenith Wireless Mechanical Battery Operated Chime... Manual de usuario

Heath Zenith

Heath Zenith Wireless Strobe Chime 6144 Manual de usuario

Heath Zenith

Heath Zenith 6106 Manual de usuario

Heath Zenith

Heath Zenith 598-1215-01 Manual de usuario

Heath Zenith

Heath Zenith 6180 Series Manual de usuario

Heath Zenith

Heath Zenith 7309 Manual de usuario

Heath Zenith

Heath Zenith SL-6164 Manual de usuario

Heath Zenith

Heath Zenith Notif Manual de usuario

Heath Zenith

Heath Zenith Weatherproof Long Range Wireless Chime with Chime Extender... Manual de usuario

Heath Zenith

Heath Zenith 598-1109-06 Manual de usuario

Heath Zenith

Heath Zenith Hardwired Electronic Chime 598-1113-05 Manual de usuario

Heath Zenith

Heath Zenith DualBrite 5716 Manual de usuario

Heath Zenith

Heath Zenith 595-5707-06 Manual de usuario

Heath Zenith

Heath Zenith Hardwired Electronic Chime 598-1313-00 Manual de usuario

Heath Zenith

Heath Zenith DESA 6270 Manual de usuario

Heath Zenith

Heath Zenith Decorative Wireless Chime 598-1000-07 Manual de usuario

Heath Zenith

Heath Zenith SL-6155 Series Manual de usuario

Heath Zenith

Heath Zenith 5867 Manual de servicio

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-05 Manual de usuario

Heath Zenith

Heath Zenith 7307 Manual de usuario

Heath Zenith

Heath Zenith Notifi Elite Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario