Heath Zenith 7307 Manual de usuario

1. Remove orange battery tab from push

button. Remove back of case by pushing in

tab on bottom with a small screwdriver (see

Figure 1). Remove orange battery tab.

2. Plug in wireless chime (see Figure 2).

IMPORTANT: This power unit is intended to

be correctly orientated in its vertical mount

position.

This plug will ﬁt into the power outlet only as

recommended by the manufacturer. Do not

try reversing the plug.This is a safety feature.

If you are unable to insert the plug fully into

the outlet, contact your electrician to replace

your obsolete outlet.

Test range. Temporarily position push button

where you want it mounted.Press push button

to verify chime and push button work properly.

If chime does not sound, see Troubleshooting.

Figure 1

WARNING: To prevent possible

SERIOUS INJURY or DEATH:

• NEVER allow small children near

batteries.

• If battery is swallowed, immediately

notify doctor.

This package includes (Style of push button and chime may vary from illustration):

Model

Wireless

plug-in

chime

Wireless push

button

Hardware

pack

7307 ✔ ✔ ✔

Figure 2

Wireless Plug-In

Chime

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

4. Mount push button. Use either screws or

double sided tape to mount push button.

• Screw Mounting: To mount with screws,

remove back of case by pushing in tab

on bottom with a small screwdriver (see

Figure 1). Note: Remove material in screw

holes (if needed) before mounting with

screws. Attach back of case to door jamb

or wall (see Figure 3). Snap front of push

button on.

• Tape Mounting: When attaching push but-

ton using double sided tape, make sure the

surface of the door jamb or wall is clean.

Figure 3

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Tune Setting Table

Multifunction Button

Tune Settings

The chime has different selectable tunes: Ding (one note tune), Ding-Dong

(two note tune), Westminster, or Whittington. The factory setting is for the

Westminster tune. This tune can be changed by following the instructions in

the Tune Setting Table.

Note: All chime models are designed to work with up to 5 push buttons (sold

separately). All chimes are designed to play only two different tunes no matter

how many push buttons are used.

Push Button Chime Tune

Jumper - ON

(Back Door)

——— Ding

Jumper - OFF

(Front Door)

Press and release button on chime.

Listen for selected tune. Repeat to

select different tune.

Selected

Musical Tune

Inside Push Button

Jumper Off Jumper On

Tune Selection Guide

Front Door

Ding-Dong

Westminster

Whittington

Back Door

Ding

1 2

CR2032

TYPE “C”

1 2 3 4 5 6 7 8

CR2032

1 2

TYPE “C”

1 2 3 4 5 6 7 8

PRESS & HOLD

TUNE - 1 SEC

SYNC - 3 SEC

RESET - 10 SEC

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Troubleshooting

1. PROBLEM: Chime does not sound or rang one time and quit.

A. POSSIBLE CAUSE: Push button and chime are not synced.

A. CORRECTIVE ACTION: Sync the push button and chime.

• Press and hold the button on the chime until the chime sounds a

“Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a

“Beep-Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

B. POSSIBLE CAUSE: Push button battery is not installed correctly.

B. CORRECTIVE ACTION: Make sure battery is installed according to the

diagram inside the push button.

C. POSSIBLE CAUSE: Push button battery is dead.

C. CORRECTIVE ACTION: Check charge of push button battery and replace

if necessary.

D. POSSIBLE CAUSE: Chime is not receiving power.

D. CORRECTIVE ACTION: Make sure the plug-in chime has power.

2. PROBLEM: Push button battery seems okay, but the chime does not work

after installation.

A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near

metal studs. Note: Metal reduces transmission range.

A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims

to move push button away from metal surface. Move chime to a different

wall outlet.

B. POSSIBLE CAUSE: Chime is mounted near concrete ﬂoor or wall.Note:

Concrete may reduce range.

B. CORRECTIVE ACTION: Move chime away from concrete surface.

C. POSSIBLE CAUSE: Chime and push button are installed too far apart.

C. CORRECTIVE ACTION: Locate chime closer to push button.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

3. PROBLEM: Chime sounds when not intended (false triggers).

POSSIBLE CAUSE: Chime is receiving interference from another wire-

less device.

CORRECTIVE ACTION: Reset chime and push button.

• Remove push button battery. Wait 30 seconds.

• Press and hold the push button for 10 to 15 seconds within 60 seconds

after installing battery into the push button.

• Press and hold the button on the chime until the chime sounds a

“Beep-Beep-Beep-Beep”.

• To re-sync the push button and chime, press and hold the button on

the chime until the chime sounds a “Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a

“Beep-Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

Note: The push button and chime come synced from the factory. The range of

the wireless chime can vary with location, temperature, and battery condition.

PRESS & HOLD

TUNE - 1 SEC

SYNC - 3 SEC

RESET - 10 SEC

PRESS & HOLD

TUNE - 1 SEC

SYNC - 3 SEC

RESET - 10 SEC

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Please contact us for assistance

before returning product to the

store or to HeathCo LLC.

If you experience a problem, follow

this guide.You may also contact us be-

tween 8:00 AM to 5:00 PM CST (M-F).

When contacting Technical Service,

please include the following informa-

tion: Name, Street Address, Daytime

Phone Number, Email Address, Model

Number, Date of Purchase, Place of

Purchase, Product Issue, and DATED

SALES RECEIPT FOR WARRANTY

REQUESTS.

Technical Service

No Service Parts Available for this

Product

HeathCo LLC

P.O. Box 90045

2445 Nashville Road

Bowling Green, KY 42101, USA

ATTN: Technical Service

Internet: www.hzsupport.com

Phone:1-800-858-8501 (English Only)

Fax: 1-270-846-8500

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

HeathCo LLC reserves the right to discontinue and to change speciﬁcations

at any time without notice without incurring any obligation to incorporate new

features in previously sold products.

ONE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights. You

may also have other rights which vary from state to state or province

to province.

For a period of one year from the date of purchase, any malfunction

caused by factory defective parts or workmanship will be corrected at

no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, light bulbs, batteries, and other expendable items

are not covered by this warranty. Any damage to the light ﬁxture resulting

from the use of chemicals or a pressure washer machine are not covered

by this warranty. Unauthorized service or modiﬁcation of the product or

of any furnished component will void this warranty in its entirety. This

warranty does not include reimbursement for inconvenience, installation,

setup time, loss of use, unauthorized service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not

extended to other equipment and components that a customer uses in

conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRAN-

TIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRE-

SENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE

PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND

SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE

CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART

OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITEDTO ANY

LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEE-

ABLE. Some states or provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion

may not apply to you.

Please keep your dated sales receipt, it is required for all warranty

requests.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Campana

inalámbrica con luz

estroboscópica

1. Retire la pestaña naranja de la batería del

botón pulsador. Extraer la parte posterior de

la caja presionando la aleta en el botón con

un destornillador pequeño (vea la Figura 1).

Quite la aleta anaranjada de la batería.

2. Campana inalámbrica enchufable.

IMPORTANTE: Esta unidad de alimentación

está diseñada para orientarse correctamente

en su posición de montaje vertical.

Este enchufe se encajará en el tomacorriente

solo según lo recomendado por el fabricante.

No trate de invertir el enchufe. Esta es una

característica de seguridad. Si no puede

insertar el enchufe en el tomacorriente por

completo, comuníquese con su electricista

para reemplazar su tomacorriente obsoleto.

ADVERTENCIA: Para prevenir una

posible LESIÓN SERIA o LA MUERTE:

• NUNCA deje que los niños estén cerca

de las baterías.

• Si se traga una batería, notiﬁque inme-

diatamente al doctor.

Figura 1

Figura 2

Este paquete tiene (El estilo del pulsador y de la campana puede variar de

la ilustración):

Modelo

Campana

inalámbrica

enchufable

Pulsador

inalámbrico

Paquete de

ferretería

7307 ✔ ✔ ✔

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Figura 3

3. Pruebe el alcance. Ponga provisionalmente

el pulsador en la posición donde lo quiera

instalar. Presione el pulsador para veriﬁcar

que la campana y el pulsador funcionen

apropiadamente. Si la campana no suena,

vea Análisis de Averías.

4. Instale el pulsador. Use ya sean tornillos o

cinta adhesiva por ambas caras para instalar

el pulsador.

• Montaje con tornillos: Para montar con

tornillos, quite la parte de atrás de la caja

empujando hacia adentro la lengüeta de

abajo con un destornillador pequeño y

girando la cuchilla (vea la Figura 1). Nota:

Quite la suciedad de los orificios para

tornillos (si es necesario) antes de poner

los tornillos. Coloque la parte de atrás de

la caja contra la jamba o la pared (vea la

Figura 3). Encaje a presión la parte frontal

del pulsador.

• Montaje con cinta adhesiva: Cuando

ﬁje el pulsador usando cinta adhesiva por

ambas caras, asegúrese que la superﬁcie

de la pared o la del batiente de la puerta

estén limpias.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Programación del tono

La campanilla tiene diferentes melodías que se pueden seleccionar: Ding

(melodía de una nota), Ding-Dong (melodía de dos notas), Westminster, o Whit-

tington.La calibración de fábrica es el tono Westminster. Esta melodía se puede

cambiar siguiendo las instrucciones de la Tabla de Programación de Melodías.

Nota: Todos los modelos de campanillas están diseñados para trabajar hasta

con 5 botones pulsadores (se venden por separado). Todas las campanillas

están diseñadas para reproducir solo dos melodías diferentes, sin importar

cuántos botones pulsadores se utilicen.

Tabla de programación de melodías

Botón Multifunción

Botón

pulsador

Campanilla Ajustes

Puente:

ENCENDIDO

(Puerta posterior)

———

Ding

Puente:

APAGADO

(Puerta principal)

Presione y suelte el botón de la campa-

na. Escuche el tono seleccionado. Re-

pita para seleccionar un tono diferente.

Melodía

musical

seleccionada

Dentro del Pulsador

Guía de Selección de Tonos

Puerta del frente

Ding-Dong

Westminster

Whittington

Puerta de atrás

Ding

1 2

CR2032

TYPE “C”

1 2 3 4 5 6 7 8

CR2032

1 2

TYPE “C”

1 2 3 4 5 6 7 8

PRESS & HOLD

TUNE - 1 SEC

SYNC - 3 SEC

RESET - 10 SEC

Puente Apagado Puente Encendido

(Off) (On)

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios de Heath Zenith

Heath Zenith

Heath Zenith DUAL BRITE SL-5597 Manual de usuario

Heath Zenith

Heath Zenith 5610 Manual de usuario

Heath Zenith

Heath Zenith 6168 Manual de usuario

Heath Zenith

Heath Zenith SECUR360 9600 Manual de usuario

Heath Zenith

Heath Zenith Notifi Elite Manual de usuario

Heath Zenith

Heath Zenith 121AC Manual de usuario

Heath Zenith

Heath Zenith Decorative Wireless Chime 6180 Manual de usuario

Heath Zenith

Heath Zenith Wireless Chime TR-0095-RX Manual de usuario

Heath Zenith

Heath Zenith SL-6153 Manual de usuario

Heath Zenith

Heath Zenith 29 Manual de usuario

Heath Zenith

Heath Zenith 7797 Manual de usuario

Heath Zenith

Heath Zenith Wireless Push Button Accessory SL-6190... Manual de usuario

Heath Zenith

Heath Zenith 5316 Manual de usuario

Heath Zenith

Heath Zenith Notif Manual de usuario

Heath Zenith

Heath Zenith DualBrite Replacement Sensor Head 2LBN3 Manual de servicio

Heath Zenith

Heath Zenith SL-6200 Manual de usuario

Heath Zenith

Heath Zenith SL-7464-03 Manual de usuario

Heath Zenith

Heath Zenith Lighted Wireless Push Button Accessory Manual de usuario

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-05 Manual de usuario

Heath Zenith

Heath Zenith 5867 Manual de servicio

Heath Zenith

Heath Zenith SL-6155 Series Manual de usuario

Heath Zenith

Heath Zenith SL-6143 Manual de usuario

Heath Zenith

Heath Zenith Single Entrance Chime 23/M Manual de usuario

Heath Zenith

Heath Zenith 7143 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario