Heath Zenith 7306 Manual de usuario

Wireless Chime

1. Remove orange battery tab from push button.

Remove back of case by pushing in tab on bottom

with a small screwdriver (see Figure 1). Remove

orange battery tab.

2. Install 2 alkaline“AA”batteries. Press in latch on

rear of chime and lift off battery cover (see Figure 2).

Install 2 alkaline “AA” batteries (not included) into

chime. Make sure batteries are installed according

to the diagram inside the chime (see Figure 3).

Replace battery access door onto back of chime.

3. Test range. Temporarily position chime and push

button where you want them mounted. Press push

button to verify chime and push button work prop-

erly. If chime does not sound, see Troubleshooting.

Figure 1

Figure 2

Figure 3

WARNING:To prevent possible SERIOUS

INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify

doctor.

This chime requires 2 “AA” alkaline batteries (not included). In typical use,

alkaline batteries will last up to one year.

This package includes (Style of push button and chime may vary from illustration):

Model

Wireless

chime Wireless push

button Hardware

pack

7306 ✔ ✔ ✔

TUNE– HOLD

1SECOND.

SYNC– HOLD

3SECONDS.

RESET– HOLD

10SECONDS.

TUNE– HOLD

1SECOND.

SYNC– HOLD

3SECONDS.

RESET– HOLD

10SECONDS.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

TUNE– HOLD

1 SECOND.

SYNC– HOLD

3 SECONDS.

RESET– HOLD

10 SECONDS.

4. Mount push button. Use either screws or double

sided tape to mount push button.

•

Screw Mounting: To mount with screws, remove

back of case by pushing in tab on bottom with a

small screwdriver (see Figure 1). Note: Remove

material in screw holes (if needed) before mounting

with screws. Attach back of case to door jamb or

wall (see Figure 4). Snap front of push button on.

• Tape Mounting: When attaching push button

using double sided tape, make sure the surface

of the door jamb or wall is clean.

5. Mount chime. Determine mounting location.

• Drill 7/32" (5.5 mm) diameter pilot hole for wall

anchor.

• Mount keyhole screw to wall leaving about 1/8"

(3 mm) of the screw threads exposed.

• Using keyhole on back of chime base, hang base

on screw (see Figure 5).

Figure 5

Figure 4

Keyhole Slot

Keyhole Screw

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Tune Settings

The chime has different selectable tunes:Ding (one note tune), Ding-Dong (two note

tune), Westminster, or Whittington.The factory setting is for the Westminster tune.

This tune can be changed by following the instructions in the Tune Setting Table.

Note: All chime models are designed to work with up to 5 push buttons (sold

separately). All chimes are designed to play only two different tunes no matter how

many push buttons are used.

Tune Setting Table

Inside Push Button

Back of Chime

Jumper Off Jumper On

Push Button Chime Tune

Jumper - ON

(Back Door)

——— Ding

Jumper - OFF

(Front Door)

Press and release button on chime.

Listen for selected tune. Repeat to

select different tune.

Selected Musical

Tune

Tune Selection Guide

Front Door

Ding-Dong

Westminster

Whittington

Back Door

Ding

1 2

CR2032

TYPE “C”

1 2 3 4 5 6 7 8

CR2032

1 2

TYPE “C”

1 2 3 4 5 6 7 8

TUNE – HOLD

1 SECOND.

SYNC – HOLD

3 SECONDS.

RESET – HOLD

10 SECONDS.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Troubleshooting

1. PROBLEM: Chime does not sound.

A. POSSIBLE CAUSE: Push button and chime are not synced.

A. CORRECTIVE ACTION: Sync the push button and chime.

• Press and hold the button on the chime until the chime sounds a “Beep-

Beep”.

• Press the push button within 30 seconds. The chime will sound a “Beep-

Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

B. POSSIBLE CAUSE: Batteries not installed correctly.

B. CORRECTIVE ACTION: Make sure batteries are installed according to the

diagram inside the push button and chime.

C. POSSIBLE CAUSE: Batteries are dead.

C. CORRECTIVE ACTION: Check charge of push button and chime batteries

and replace if necessary.

2. PROBLEM: Batteries seem okay, but the chime does not work after installation.

A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near metal

studs. Note: Metal reduces transmission range.

A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to

move chime or push button away from metal surface.

B. POSSIBLE CAUSE: Chime is mounted near concrete ﬂoor or wall. Note:

Concrete may reduce range.

B. CORRECTIVE ACTION: Move chime away from concrete surface.

C. POSSIBLE CAUSE: Chime and push button are installed too far apart.

C. CORRECTIVE ACTION: Locate chime closer to push button.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

3. PROBLEM: Chime sounds when not intended (false triggers).

POSSIBLE CAUSE: Chime is receiving interference from another wireless

device.

CORRECTIVE ACTION: Reset chime and push button.

• Remove push button battery. Wait 30 seconds.

• Press and hold the push button for 10 to 15 seconds within 60 seconds

after installing battery into the push button.

• Press and hold the button on the chime until the chime sounds a “Beep-

Beep-Beep-Beep”.

• To re-sync the push button and chime, press and hold the button on the

chime until the chime sounds a “Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a “Beep-

Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

Note: The push button and chime come synced from the factory. The range of the

wireless chime can vary with location, temperature, and battery condition.

TUNE – HOLD

1 SECOND.

SYNC – HOLD

3 SECONDS.

RESET – HOLD

10 SECONDS.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Please contact us for assistance

before returning product to the

store or to HeathCo LLC.

If you experience a problem, follow this

guide.You may also contact us between

8:00 AM to 5:00 PM CST (M-F).

When contacting Technical Service,

please include the following informa-

tion: Name, Street Address, Daytime

Phone Number, Email Address, Model

Number, Date of Purchase, Place of

Purchase, Product Issue, and DATED

SALES RECEIPT FOR WARRANTY

REQUESTS.

Technical Service

No Service Parts Available for this

Product

HeathCo LLC

P.O. Box 90045

2445 Nashville Road

Bowling Green, KY 42101, USA

ATTN: Technical Service

Internet: www.hzsupport.com

Phone: 1-800-858-8501 (English Only)

Fax: 1-270-846-8500

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

HeathCo LLC reserves the right to discontinue and to change speciﬁcations at any

time without notice without incurring any obligation to incorporate new features in

previously sold products.

ONE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights. You may

also have other rights which vary from state to state or province to province.

For a period of one year from the date of purchase, any malfunction caused by

factory defective parts or workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, light bulbs, batteries, and other expendable items are

not covered by this warranty. Any damage to the light ﬁxture resulting from the

use of chemicals or a pressure washer machine are not covered by this war-

ranty. Unauthorized service or modiﬁcation of the product or of any furnished

component will void this warranty in its entirety. This warranty does not include

reimbursement for inconvenience, installation, setup time, loss of use, unauthor-

ized service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not extended

to other equipment and components that a customer uses in conjunction with

our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION

OR CONDITION OF MERCHANT ABILITY OR THATTHE PRODUCTS ARE FIT

FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF

ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUS-

TOMER ANDTHERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO

LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS

OR PROFITS,WHETHER OR NOT FORESEEABLE.Some states or provinces

do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation or exclusion may not apply to you.

Please keep your dated sales receipt,it is required for all warranty requests.

Campana Inalámbrica

1. Retire la pestaña naranja de la batería del botón

pulsador. Extraer la parte posterior de la caja pre-

sionando la aleta en el botón con un destornillador

pequeño (vea la Figura 1).Quite la aleta anaranjada

de la batería.

Coloque las 2 pilas alkalinas “AA”.

Presione el

seguro en la parte de atrás de la campana y levante

la tapa de la pila (vea la Figura 2).Instale 2 baterías

alcalinas “AA” (no se incluyen) en la campanilla.

Asegúrese de que las baterías estén instaladas

según el diagrama del interior de la campanilla (vea

la Figura 3).Volver a colocar la puerta de acceso de

la batería sobre la parte posterior de la campanilla.

3. Pruebe el alcance. Ponga provisionalmente la

campana y el pulsador en la posición donde los

quiera instalar. Presione el pulsador para veriﬁcar

que la campana y el pulsador funcionen apropia-

damente. Si la campana no suena, vea Análisis de

Averías.

ADVERTENCIA: Para prevenir una posible

LESIÓN SERIA o LA MUERTE:

• NUNCA deje que los niños estén cerca de las

baterías.

• Si se traga una batería, notiﬁque inmediata-

mente al doctor.

Esta campana requiere 2 pilas alcalinas tipo “AA” (no incluidas). Con un uso

normal, las pilas alcalinas durarán hasta 1 año.

Este paquete tiene (El estilo del pulsador y de la campana puede variar de la

ilustración):

Modelo

Campana

inalámbrica Pulsador

inalámbrico Paquete de

ferretería

7306 ✔ ✔ ✔

Figura 1

Figura 2

Figura 3

TUNE– HOLD

1SECOND.

SYNC– HOLD

3SECONDS.

RESET– HOLD

10SECONDS.

TUNE– HOLD

1SECOND.

SYNC– HOLD

3SECONDS.

RESET– HOLD

10SECONDS.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Figura 4

4. Instale el pulsador. Use ya sean tornillos o cinta

adhesiva por ambas caras para instalar el pulsador.

• Montaje con tornillos: Para montar con tornillos,

quite la parte de atrás de la caja empujando

hacia adentro la lengüeta de abajo con un

destornillador pequeño y girando la cuchilla

(vea la Figura 1). Nota: Quite la suciedad de los

oriﬁcios para tornillos (si es necesario) antes de

poner los tornillos. Coloque la parte de atrás de la

caja contra la jamba o la pared (vea la Figura 4).

Encaje a presión la parte frontal del pulsador.

• Montaje con cinta adhesiva: Cuando ﬁje el

pulsador usando cinta adhesiva por ambas caras,

asegúrese que la superﬁcie de la pared o la del

batiente de la puerta estén limpias.

5. Monte la campana. Determine el sitio para el

montaje.

• Perfore un agujero piloto de 5.5 mm (7/32 pulga-

das) de diámetro para el ancla de pared.

• Coloque el tornillo del oriﬁcio de alineación en la

pared dejando 3 mm (1/8 de pulgada) de la rosca

del tornillo sin apretar.

• Usando este oriﬁcio de alineación de la parte

posterior de la base de la campana, cuelgue la

base en el tornillo (vea la Figura 5).

Figura 5

TUNE– HOLD

1 SECOND.

SYNC– HOLD

3 SECONDS.

RESET– HOLD

10 SECONDS.

Agujero de alineación

Tornillo para el

agujero de alineación

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Tabla de programación de melodías

Dentro del Pulsador

Programación del tono

La campanilla tiene diferentes melodías que se pueden seleccionar: Ding (melodía

de una nota), Ding-Dong (melodía de dos notas), Westminster, o Whittington. La

calibración de fábrica es el tono Westminster. Esta melodía se puede cambiar

siguiendo las instrucciones de la Tabla de Programación de Melodías.

Nota: Todos los modelos de campanillas están diseñados para trabajar hasta con

5 botones pulsadores (se venden por separado). Todas las campanillas están

diseñadas para reproducir solo dos melodías diferentes, sin importar cuántos

botones pulsadores se utilicen.

Botón

pulsador

Campanilla Ajustes

Puente:

ENCENDIDO

(Puerta posterior)

———

Ding

Puente:

APAGADO

(Puerta principal)

Presione y suelte el botón de la campana.

Escuche el tono seleccionado. Repita

para seleccionar un tono diferente.

Melodía

musical

seleccionada

Puente Apagado (Off) Puente Encendido (On)

Guía de Selección de Tonos

Puerta del frente

Ding-Dong

Westminster

Whittington

Puerta de atrás

Ding

Parte de atrás de la campana

1 2

CR2032

TYPE “C”

1 2 3 4 5 6 7 8

CR2032

1 2

TYPE “C”

1 2 3 4 5 6 7 8

TUNE – HOLD

1 SECOND.

SYNC – HOLD

3 SECONDS.

RESET – HOLD

10 SECONDS.

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios de Heath Zenith

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-06 Manual de usuario

Heath Zenith

Heath Zenith SL-7464-03 Manual de usuario

Heath Zenith

Heath Zenith 7143 Manual de usuario

Heath Zenith

Heath Zenith Dual Brite SL-5597 Manual de usuario

Heath Zenith

Heath Zenith DualBrite Manual de usuario

Heath Zenith

Heath Zenith 7311 Manual de usuario

Heath Zenith

Heath Zenith 6106 Manual de usuario

Heath Zenith

Heath Zenith DualBrite 5716 Manual de usuario

Heath Zenith

Heath Zenith SL-6155 Series Manual de usuario

Heath Zenith

Heath Zenith Hardwired Electronic Chime 598-1113-05 Manual de usuario

Heath Zenith

Heath Zenith Wireless Chime 598-1172-04 Manual de usuario

Heath Zenith

Heath Zenith 7762 Manual de usuario

Heath Zenith

Heath Zenith 5867 Manual de servicio

Heath Zenith

Heath Zenith 595-5707-06 Manual de usuario

Heath Zenith

Heath Zenith 5210 Manual de usuario

Heath Zenith

Heath Zenith 7309 Manual de usuario

Heath Zenith

Heath Zenith 595-5684-09 Manual de usuario

Heath Zenith

Heath Zenith Hardwired Electronic Chime 598-1313-00 Manual de usuario

Heath Zenith

Heath Zenith 6168 Manual de usuario

Heath Zenith

Heath Zenith SL-6166 Manual de usuario

Heath Zenith

Heath Zenith 598-1143-01 Manual de usuario

Heath Zenith

Heath Zenith Wireless Mechanical Chime 598-1123-02 Manual de usuario

Heath Zenith

Heath Zenith 5838 Manual de usuario

Heath Zenith

Heath Zenith SL-6168 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario