HBM Z16A Manual de usuario
Operating Manual | Bedienungsanleitung |
Manuel d'emploi
English Deutsch Français
Z16A
Hottinger Baldwin Messtechnik GmbH
Im Tiefen See 45
D-64293 Darmstadt
Tel. +49 6151 803-0
Fax +49 6151 803-9100
www.hbm.com
Mat.: 7-0101.0020
DVS: A04000_03_Y00_00 HBM: public
01.2020
EHottinger Baldwin Messtechnik GmbH.
Subject to modifications.
All product descriptions are for general information only.
They are not to be understood as a guarantee of quality or
durability.
Änderungen vorbehalten.
Alle Angaben beschreiben unsere Produkte in allgemeiner
Form. Sie stellen keine Beschaffenheits- oder Haltbarkeits
garantie dar.
Sous réserve de modifications.
Les caractéristiques indiquées ne décrivent nos produits
que sous une forme générale. Elles n'impliquent aucune
garantie de qualité ou de durabilité.
Operating Manual | Bedienungsanleitung |
Manuel d'emploi
English Deutsch Français
Z16A
2A04000_03_Y00_00 HBM: public Z16A
English
1 Safety instructions 3........................................
2 Markings used 6............................................
2.1 The marking used in this document 6...........................
2.2 Symbols on the device 6......................................
3 Scope of delivery 7.........................................
4 Structure and mode of operation 8...........................
5 Conditions on site 9........................................
6 Mechanical installation 11....................................
6.1 Important precautions during installation 11......................
6.2 Mounting and load application 12...............................
7 Electrical connection 13......................................
7.1 Connection in six-wire configuration 13..........................
7.2 Connection in four-wire configuration 13.........................
7.3 Shortening the cable 14.......................................
7.4 Cable extension 14...........................................
7.5 Parallel connection 15.........................................
7.6 EMC protection 15............................................
8 Waste disposal and environmental protection 17..............
9 Specifications 18............................................
10 Dimensions 20..............................................
10.1 Z16A… 20...................................................
10.2 Z16A… (7.5 t + 15 t) with knuckle eyes 21.......................
10.3 Z16A... with threaded connector 22.............................
Safety instructions
Z16A A04000_03_Y00_00 HBM: public 3
1 Safety instructions
Appropriate use
Transducers of the Z16A... type series are designed for technical weighing
applications within the limits detailed in the specifications. The load cell must
only be used for tensile loads. Any other use is not appropriate.
Any person instructed to carry out installation, commissioning or operation of
the transducer must have read and understood the Operating Manual and in
particular the technical safety instructions.
In the interests of safety, the transducer should only be operated by qualified
personnel and as described in the Operating Manual. It is also essential to
comply with the legal and safety requirements for the application concerned
during use. The same applies to the use of accessories.
The transducer is not intended for use as a safety component. Please also
refer to the section: "Additional safety precautions". Proper and safe operation
requires proper transportation, correct storage, siting and mounting, and
careful operation.
Operating conditions
SPlease observe the permissible maximum values stated in the
specifications for:
- Limit load
- Breaking loads
- Temperature limits
- Limits of electrical loading capacity
SNote, that when several transducers are installed in a scale, there is not
always an even distribution of load on the individual transducers.
SThe transducers can be used as machine elements. When used in this
manner, it must be noted that, to favor greater sensitivity, the transducer
has not been designed with the safety factors usual in mechanical
engineering.
Safety instructions
4A04000_03_Y00_00 HBM: public Z16A
SThe transducer must not be modified from the design or safety engineering
point of view except with our express agreement.
SThe transducer is maintenance-free.
SIn accordance with national and local environmental protection and material
recovery and recycling regulations, old transducers that can no longer be
used must be disposed of separately and not with normal household
garbage, see Chapter 8, Page 17.
Explosion protection version option
SPlease comply with the relevant code of practice during installation.
SThere must be compliance with the installation conditions cited in the
Certificate of Conformity and/or the Type Certificate.
Qualified personnel
Qualified persons means persons entrusted with the installation, fitting,
commissioning and operation of the product who possess the appropriate
qualifications for their function.
This includes people who meet at least one of the three following requirements:
SKnowledge of the safety concepts of measurement and automation
technology is a requirement and as project personnel, they must be familiar
with these concepts.
SAs measurement or automation plant operating personnel, they have been
instructed how to handle the machinery. They are familiar with the operation
of the equipment and technologies described in this documentation.
SAs commissioning engineers or service engineers, they have successfully
completed the training to qualify them to repair the automation systems.
They are also authorized to activate, ground and label circuits and
equipment in accordance with safety engineering standards.
Additional safety precautions
Additional safety precautions to meet the requirements of the relevant national
and local accident prevention regulations must be taken in plants where
malfunctions could cause major damage, loss of data or even personal injury.
Safety instructions
Z16A A04000_03_Y00_00 HBM: public 5
The scope of supply and performance of the transducer covers only a small
area of measurement technology. Before starting up the transducer in a
system, a project planning and risk analysis must first be implemented, taking
into account all the safety aspects of measurement and automation technology
so that residual risks are minimized. This particularly concerns personal and
machine protection. The transducers function passively and cannot implement
any (safety-relevant) cutoffs. In the event of a fault, the relevant precautions
must establish safe operating conditions.
General dangers of failing to follow the safety instructions
The transducer corresponds to the state of the art and is failsafe. The
transducer may give rise to residual dangers if it is inappropriately installed or
operated.
Markings used
6A04000_03_Y00_00 HBM: public Z16A
2 Markings used
2.1 The marking used in this document
Important instructions for your safety are specifically identified. It is essential to
follow these instructions in order to prevent accidents and damage to property.
Symbol Significance
WARNING This marking warns of a potentially dangerous
situation in which failure to comply with safety
requirements can result in death or serious physical
injury.
Note This marking draws your attention to a situation in
which failure to comply with safety requirements can
lead to damage to property.
Important
This marking draws your attention to important
information about the product or about handling the
product.
Emphasis
See …
Italics are used to emphasize and highlight text and
identify references to sections, diagrams, or external
documents and files.
2.2 Symbols on the device
CE certification
The CE mark enables the manufacturer to guarantee that
the product complies with the requirements of the
relevant EC directives (the Declaration of Conformity can
be found on the HBM website (www.hbm.com) under
HBMdoc).
Scope of delivery
Z16A A04000_03_Y00_00 HBM: public 7
3 Scope of delivery
Included in the scope of supply:
SSG with connecting cable
SBag with lubricating grease
SAssembly instructions
Accessories (not included in the scope of supply)
SKnuckle eye, Order No. 1-U2A/10T/ZGOW
SThread adapter M36x3, Order No. 1-Z16/ADAPTERM36X3
SGround cable, Order No. e.g. 1-EEK6
Structure and mode of operation
8A04000_03_Y00_00 HBM: public Z16A
4 Structure and mode of operation
The measuring element is a steel loaded member to which strain gages (SG)
are applied. The SG are arranged so that two are stretched and the other two
compressed when a load acts on the transducer.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
Otros manuales de Transductor de HBM
HBM
HBM PW15iA Manual de usuario
HBM
HBM Z7A Series Manual de usuario
HBM
HBM AED9101D Manual de usuario
HBM
HBM U93 Manual de usuario
HBM
HBM T20WN Manual de usuario
HBM
HBM U3 Manual de usuario
HBM
HBM T12 Manual de usuario
HBM
HBM T5 Manual de usuario
HBM
HBM C4 Manual de usuario
HBM
HBM Z6R Series Manual de usuario
HBM
HBM U5 Series Manual de usuario
HBM
HBM SLB-700A Manual de usuario
HBM
HBM T32 FNA Manual de usuario
HBM
HBM T40MS Manual de usuario
HBM
HBM SLB-700A Manual de usuario
HBM
HBM S2 Manual de usuario
HBM
HBM BN100A Manual de usuario
HBM
HBM T40B Manual de usuario
HBM
HBM TB2 Manual de usuario
HBM
HBM DD1 Series Manual de usuario
Manuales populares de Transductor de otras marcas
Camille Bauer
Camille Bauer SINEAX F534 Manual de usuario
Trane
Trane KIT 16724 Instrucciones de montaje
Lumel
Lumel P18 Manual de usuario
B&C Speakers
B&C Speakers DE75PTN Manual de usuario
MAMAC SYSTEMS
MAMAC SYSTEMS PR-243 Manual
Mianyang Weibo Electronic
Mianyang Weibo Electronic WB Series Manual de usuario
