Gefen DVI 2500HD Manual de usuario

www.gefen.com

DVI 2500HD

Optical DVI Dual Link Extension

EXT-DVI-2500HD

User Manual

ASKING FOR ASSISTANCE

Technical Support:

Telephone (818) 772-9100

(800) 545-6900

Fax (818) 772-9120

Technical Support Hours:

8:00 AM to 5:00 PM Monday thru Friday PST

Write To:

Gefen Inc.

c/o Customer Service

20600 Nordhoff St

Chatsworth, CA 91311

www.gefen.com

[email protected]

Notice

Gefen, LLC reserves the right to make changes in the hardware, packaging and

any accompanying documentation without prior written notice.

DVI•2500HD is a trademark of Gefen, LLC.

All trademarks are the property of their respective owners.

Rev A5

CONTENTS

1 Introduction

2 Operation Notes

3 Features

4 Sender Panel Layout

5 Sender Panel Descriptions

6 Receiver Panel Layout

7 Receiver Panel Descriptions

8 Connecting And Operating The DVI•2500HD

9 Connecting The DVI•2500HD In Direct DDC Mode

10 Connecting The DVI•2500HD In Virtual DDC Mode

11 Connecting The DVI•2500HD In Virtual DDC Mode

12 Speciﬁcations

13 Warranty

Congratulations on your purchase of the DVI•2500HD. Your complete satisfaction

is very important to us.

Gefen

Gefen delivers innovative, progressive computer and electronics add-on solutions

that harness integration, extension, distribution and conversion technologies.

Gefen’s reliable, plug-and-play products supplement cross-platform computer

systems, professional audio/video environments and HDTV systems of all sizes

with hard-working solutions that are easy to implement and simple to operate.

The Gefen DVI•2500HD

The DVI•2500HD uses 4 ﬁbers to extend Dual Link DVI display up to 6,600 feet

away from your source. Dual link DVI describes the use of all 24 pins of the DVI

(digital visual interface) connector to achieve super high resolutions.

How It Works

The DVI•2500HD Sender unit sits next to your computer. A short video

cable supplied with the DVI•2500HD system connects the DVI source to the

DVI•2500HD Sender unit. The DVI•2500HD Receiver unit sits next to your DVI

display and plugs into the DVI display’s Dual-Link DVI port. One CAT-5 cable and

a LC ﬁber optic cable (4-strand) connects the Sender and the Receiver units to

each other.

Note:

The CAT5 cable is for the transmission of DDC/EDID (video timing, resolution)

information, the Hot-plug signal and DC power. The ﬁber cable carries the video

picture information.

DVI Extension can be:

• up to 500m (1640 feet) over Multi-mode ﬁber using Virtual DDC.

• up to 2 km (6,600 feet) over Single-mode ﬁber using Virtual DDC.

• up to 100m (330ft) with direct DDC using CAT5.

INTRODUCTION

READ THESE NOTES BEFORE INSTALLING OR

OPERATING THE DVI•2500HD

• LC terminated ﬁber optic cables (up to 2 pairs) are required for operation of

the DVI•2500HD system. A single CAT-5e cable will also be required when

operating in Direct DDC mode only.

• This device will accept both Single-Mode and Multi-Mode ﬁber optic cables.

• This device will accept both 50μand 62.5μmulti-mode fiber optic cable

types.

• The DVI•2500HD can operate in either Direct DDC (HDCP-Compliant) or

Virtual DDC modes. For a description of these modes, please see page 8.

• Maximum extension in Direct DDC mode is 330 feet (100 meters) at a

maximum resolution of WUXGA (2560x1600/60Hz)

• Maximum extension in Virtual DDC mode is 6,600 feet (2 kilometers) at a

maximum resolution of WUXGA (2560x1600/60Hz)

• This device will accept both Single Link and Dual Link DVI type sources/

displays. Only 1 pair of LC cables, on Channel 1, are required when using

Single Link devices. A second pair is only required, on Channel 2, when

operating this device with Dual Link devices.

• WARNING: Do not look directly into LC receptacles of the sending unit. This

device, however, does operate under the Laser Class I speciﬁcation for eye

safety.

OPERATION NOTES

Features

• Extends any dual link DVI compliant device up to 6,600 feet (2 km) from the

computer

• Uses a 4 strand multimode LC-LC ﬁber optic cable; 2-strand/1-strand

(duplex) for Single-Link

• Optionally use one CAT-5e cable for DDC and control signals

• Supports HDTV resolutions such as 720p and 1080p

• Supports up to 2560x1600 resolution at 60Hz refresh rate.

• Supports DDWG standards for DVI compliant monitors

• Supports Virtual DDC and DDC2B protocols

• HDCP-Compliant in Direct DDC mode

Package Includes

(1) DVI•2500HD Sender

(1) DVI•2500HD Receiver

(2) 12V Power Supply

(1) 6ft DVI-DL Cable (M-M)

(1) Rack Ears

(1) User Manual

FEATURES

Front Panel

Back Panel

987

SENDER PANEL LAYOUT

1 LED Power Indicator

This LED will become active once the included 5V DC power supply is properly

connected between the sender and an open wall power socket.

2 EDID Mode Selector Switch

This switch will set either the Direct DDC or Virtual DDC modes. For a

description of these modes please see page 8.

3 Self-EDID Button

This button will begin the EDID recording process when the DVI•2500HD is

operating in Virtual DDC mode. This button does not have any use in Direct

DDC mode.

4 EDID Program LED Indicator

This LED will become active after the Self-EDID button is pressed. This is to

indicate that the sending unit is ready to record the EDID of the connected DVI-

capable device.

5 LED Status Indicator

This LED will become active once the DVI source device has been properly

connected and detected. This indicator will also become active when the

sending unit is ready to record EDID after the Self-EDID button is pressed.

6 12V DC Power Receptacle

This receptacle will require power from the included 12V DC power supply for

proper operation. Connect the included power supply between this port and an

open wall power socket.

7 DDC RJ45 Port

This port is used to connect a CAT-5e cable between the sending and receiving

units for DDC2B trafﬁc. This cable is only necessary when the DVI•2500HD is

operating in Direct DDC mode.

8 DVI-D Input

This receptacle will accept either a DVI Single-Link or Dual-Link source device.

9 2 Port LC Fiber Receptacle (Channel 1)

This receptacle will accept 1 pair, or 2 single-strand, LC terminated ﬁber optic

cables. This cable is required at all times for operation.

10 2 Port LC Fiber Receptacle (Channel 2)

This receptacle will accept 1 pair, or 2 single-strand, LC terminated ﬁber optic

cables. This cable is only required for operation when Dual-Link sources are

used.

SENDER PANEL DESCRIPTIONS

Front Panel

Back Panel

874 5

RECEIVER PANEL LAYOUT

1 LED Power Indicator

This LED will become active once the included 5V DC power supply is properly

connected between the sender and an open wall power socket.

2 Channel 2 LED Link Indicator

This LED will become active once a link for Channel 2 has been established

between the sending and receiving units.

3 Channel 1 LED Link Indicator

This LED will become active once a link for Channel 1 has been established

between the sending and receiving units.

4 12V DC Power Receptacle

This receptacle will require power from the included 12V DC power supply for

proper operation. Connect the included power supply between this port and an

open wall power socket.

5 DDC RJ45 Port

This port is used to connect a CAT-5e cable between the sending and receiving

units for DDC2B trafﬁc. This cable is only necessary when the DVI•2500HD is

operating in Direct DDC mode.

6 DVI-D Output

This receptacle will accept either a DVI-capable Single-Link or Dual-Link output

device (i.e. DVI display).

7 2 Port LC Fiber Receptacle (Channel 1)

This receptacle will accept 1 pair, or 2 single-strand, LC terminated ﬁber optic

cables. This cable is required at all times for operation.

8 2 Port LC Fiber Receptacle (Channel 2)

This receptacle will accept 1 pair, or 2 single-strand, LC terminated ﬁber optic

cables. This cable is only required for operation when Dual-Link sources are

used.

RECEIVER PANEL DESCRIPTIONS

Tabla de contenidos

Otros manuales de Extensor de Gefen

Gefen

Gefen ext-hdmi-cat5x Manual de usuario

Gefen

Gefen EXT-HDMI1.3-1FO Manual de usuario

Gefen

Gefen GTB-DVIKVM-ELR-BLK Manual de usuario

Gefen

Gefen DVI-1000ST Manual de usuario

Gefen

Gefen GTV-HDBT-CAT5 Manual de usuario

Gefen

Gefen EXT-COMPAUD-CAT5-142 Manual de usuario

Gefen

Gefen EXT-UHDV-KA-LANS-TX Manual de usuario

Gefen

Gefen EXT-HDMI 1.3-1CAT6 Manual de usuario

Gefen

Gefen GTB-3DTV-KVM Manual de usuario

Gefen

Gefen EXT-PS2-100 Manual de usuario

Gefen

Gefen ToolBox GTB-USB2.0-4LR Manual de usuario

Gefen

Gefen USB 2.0 SR Manual de usuario

Gefen

Gefen EXTENDIT CAT5 8000S Manual de usuario

Gefen

Gefen EXT-HDMI1.3-CAT5-ELR Manual de usuario

Gefen

Gefen HDTV-CAT5 Manual de usuario

Gefen

Gefen CAT5-5000OLD Manual de usuario

Gefen

Gefen EXT-WRS232 Manual de usuario

Gefen

Gefen GTB-HD-DCS Manual de usuario

Gefen

Gefen EXT-3GSDI-F0-141 Manual de usuario

Gefen

Gefen DVI-CAT5-MS Manual de usuario

Gefen

Gefen RS-232 Manual de usuario

Gefen

Gefen COMPOSITE-141N Manual de usuario

Gefen

Gefen FW-1394B Manual de usuario

Gefen

Gefen DVI-141SBP Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario