Front Runner LALD006 Manual de usuario
LALD006_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
front runner
LALD006
ENG
1
Thank you for purchasing a Front Runner Land Rover Defender 90 / 110 Ladder.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
LAND ROVER DEFENDER 90 / 110
LADDER
LALD006_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
GET ORGANIZED
1
IN THE BOX
1 1 X Ladder Side - LH
2 1 X Ladder Side - RH
3 1 X Ladder Top
4 1 X Clamp
5 3 X Ladder Rung
6 1 X Bottom Step
7 1 X Support Bracket
8 12 X M6 x 12 Button Head Screw
9 24 X M6 x 12 x 1SS Flat Washer
10 24 X M6 Nyloc Nut
11 3 X M10 x 30 x 3 SS Flat Washer
12 2 X M10 x 80 Hex Head Bolt
13 2 X M6 x 19 x 1 SS Flat Washer
14 1 X M10 Flat Washer
15 1 X Spacer
16 2 X M10 Nyloc Nut
17 24 X M6 Nut Cap
18 2 X M8 Nut Cap
19 2 X M8 x 35 Hex Head Bolt
20 2 X M8 x 16 x 1.6SS Flat Washer
13mm
17mm 6mm
8.5mm
13mm
17mm
4mm
5mm
MARKER
1
8
26
12
27
11
9
16
11
15
10
14
5
6
16
17
18
19
20
7
22
23
24
22
17 10 9
2
25
13
5
5
21
3
26
IN THE BOX
21 2 X M6 x 60 Cap Screw
22 4 X PVC Washer
23 2 X M8 x 25 x 2 SS Flat Washer
24 2 X M8 Nyloc Nut
25 2 X M6 Spring Washer
26 8 X M6 x 16 Button Head Screw
27 1 X M10 x 100 Hex Head Bolt
4
17 10 9
2794
4685
0.5m
LALD006_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE2
2.1
2.2
2.3
Ensure that the Pinch Weld are assembled
onto the edges of the Ladder Top and the
Clamp as shown.
Assemble the three Ladder Rungs (Item
5) to the Ladder Sides (Items 1 & 2) using
M6 x 12 Button Head Bolts, M6 x 12 x 1SS
Flat Washers and M6 Nyloc Nuts (Items 8, 9
& 10) as shown.
Place M6 Nut Caps (Item 17) on all the Nyloc
Nuts.
4mm
10mm
17 10
8
2
1
5
26
10
17
7
9
9
Assemble the Support Bracket (Item 7) to
the Ladder Sides using M6 x 16 Button Head
Bolts, M6 x 12 x 1SS Flat Washers and M6
Nyloc Nuts (Items 9, 10 & 26) as shown.
Place M6 Nut Caps (Item 17) on all the Nyloc
Nuts.
4mm
10mm
2021
1790
1992
2794
4685
1.0m
0.5m
5cm
Scale: 1:25 All measurements in millimeters.
LALD006_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE2
2.4
2.5
2.6
Assemble the Ladder Top Assembly from 2.1
to the Ladder Sides using M6 x 16 Button
Head Bolts, M6 x 12 x 1SS Flat Washers and
M6 Nyloc Nuts (Items 9, 10 & 26) as shown.
Place M6 Nut Caps (Item 17) on all the Nyloc
Nuts.
Loosely insert two M6 x 60 Cap Screws with
M6 SS Spring Washers and M6 x 19 x 1SS
Flat Washers (Items 13, 21 & 25) through the
Clamp (Item 4) into the Ladder Top (Item 3)
as shown.
4mm
Swing open the Clamp. Fit the top asembly
into vehicle's gutter.
Align the Ladder with the edge of the door.
Inside the vehicle, remove the rear left
window cover and speaker box.
Check door clearance and make sure the
ladder is aligned straight with the door.
Mark the bottom two holes of the Ladder on
the vehicle's body and remove the Ladder.
Using a drill machine and a 6mm drill bit,
drill two pilot holes on your markings.
Change to a 8.5mm drill bit and drill the
holes to 8.5mm.
6mm
8.5mm
26
9
10
17
21
25
13
10mm
2021
1790
1992
BA
2794
4685
1.0m
0.5m
5cm
Scale: 1:25 All measurements in millimeters.
LALD006_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
5
FIT AND SECURE2
2.7
2.8
2.9
Place the ladder back onto the vehicle and
line up the holes in the bottom of the Ladder
with the holes drilled in 2.6.
Insert two M8 x 35 Hex Bolts and two M8
Flat washers (Item 19 & 20) through the
holes in the Ladder. Place two M8 PVC Flat
Washers (Item 22) over each bolt between
the vehicle and the Ladder. Secure on the
inside of the vehicle using two M8 Flat
Washers and two M8 Nyloc Nuts (Item 23 &
24).
Fully tighten the two M6 x 60 Cap Screw
clamping the Ladder to the gutter.
Refit the rear window and speaker box cover
removed in 2.6.
Place M8 Nut Caps (Item 18) on the bolt
heads.
5mm
13mm
13mm
18
19 20
22 22
23 24
6
14
11
12
27
15
12
11
24
Remove the two orginal bolts from
the bumper and place the Bottom step
(Item 6) against the body, and align with
the two holes in the bumper as shown.
Refer to 2.9 and insert the M10 x 80 Hex
Bolt with a M10 x 30 x 3 Flat Washer (Item
11 & 12) into the right hole marked "A".
Behind the bumper insert the Spacer (Item
15) between the bumper and the "Tab"
attached to the body/bumper. Guide the Hex
Bolt through the Spacer and loosely fasten
using a M10 x 30 x 3 Flat Washer and M10
Nyloc Nut (Item 11 & 24).
For the left side marked "B", insert the M10
x 80 Hex Bolt and M10 x 30 x 3 Flat Washer
(Item 11 & 12) and loosely fasten using a
M10 Flat Washer and M10 Nyloc Nut (Item
14 & 24). If the original bolt went through
the chassis and the seat belt support bar,
use the M10 x 100 Hex Bolt (Item 27).
17mm
17mm
LALD006_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
6
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
2021
1790
1992
FIT AND SECURE3
2.10
Align the Bottom step and Fully tighten all
bolts.
17mm
17mm
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Front Runner
Front Runner
Front Runner RRAC054 Manual de usuario
Front Runner
Front Runner FAJK002 Manual de instrucciones
Front Runner
Front Runner PRO UNDER RACK TABLE bracket Manual de usuario
Front Runner
Front Runner SSDS115 Manual de usuario
Front Runner
Front Runner SSAM008 Manual de usuario
Front Runner
Front Runner RRAC248 Manual de usuario
Front Runner
Front Runner FATT002 Manual de usuario
Front Runner
Front Runner RRAC137 Manual de usuario
Front Runner
Front Runner LAVT003 Manual de usuario
Front Runner
Front Runner RRAC018 Manual de usuario
Front Runner
Front Runner TOYOTA 4RUNNER Manual de usuario
Front Runner
Front Runner SSDS111 Manual de usuario
Front Runner
Front Runner LATR001 Manual de usuario
Front Runner
Front Runner Pro Water Tank with Strap Manual de usuario
Front Runner
Front Runner RRAC119 Manual de usuario
Front Runner
Front Runner KRTT001T Manual de usuario
Front Runner
Front Runner SSDS802 Manual de usuario
Front Runner
Front Runner JADA010 Manual de usuario
Front Runner
Front Runner PBTH001 Manual de usuario
Front Runner
Front Runner FSLI022 Manual de usuario
