Front Runner RRAC137 Manual de usuario
RRAC137_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
Pro Canoe &
Kayak Carrier
front runner
RRAC137
ENG
1
Thank you for purchasing a Front Runner Pro Canoe & Kayak Carrier.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
RRAC137_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
GET ORGANIZED
1
IN THE BOX
1
1
2
3
4
7
9
10
2
6
1 2 X Pro Canoe & Kayak Carrier
2 8 X M8 x 20 Hex Bolt
3 4 X M8 Nyloc Nut
4 4 X M8 Nut Cap
5 4 X M6 x 25 Button Head
6 4 X M6 Nyloc Nut
7 4 X M6 Nut Cap
8 1 X Stratchit with Carabiner (Pair)
9 4 X M8 Eye Nut
10 4 X M8 Nylon Washer
4mm
13mm
10mm
8
5
A(2:1)
A(2:1)
2
RRAC137_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE2
2.1
2.2
2.3
4mm
10mm
13mm
Decide where on your rack you would like
to place your Pro Canoe / Kayak Carriers
(Item 1). Work out the correct spacing
between the two Carriers according to the
the length of what you are carrying.
Slide four M8 x 20 Hex Bolts (Item 2) into the
machined slot of each of the two chosen
slats. Place each Carrier over two Hex Bolts.
Loosely fasten the Carriers to the rack using
M8 Nyloc Nut (Item 3) as shown.
Position the two Carriers left to right as
required and fully tighten all the Nyloc Nuts.
Place an M8 Nut Cap (Item 4) over each of
the Nyloc Nuts.
Each Carrier has three settings, allowing
you to adjust the angle. (Refer to Step 2.3).
Loosen and remove the two M6 x 25 Button
Head Bolts (Item 5).
Adjust the Carrier up or down as required,
aligning the hole on the outside of the
Carrier with one of the three adjustment
holes on the inside of the Carrier.
Lock the Carrier in the chosen position by
using the M6 x 25 Button Head and
M6 Nyloc Nuts (Items 5 & 6) removed earlier
and fully tighten.
Place M6 Nut Caps (Item 7) over the Nyloc
Nuts.
Secure your Kayak / Canoe using the
Stratchits supplied. The carabiners are
attached to the Carriers on one of the cross
bars as indicated in Step 2.3.
Should your Kayak be extra wide, the
Stratchits can be attached to the M8 Eye
Nuts (Item 9) by fixing them in the T- Slots
of your Rack, using M8 x 16 Hex Bolts and
M8 Nylon Washers (Items 2 & 10).
1
3
4
5
6
7
RRAC137_REV A04_ © 2022 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE2
2.4
2.5
If you want to create more space on your
rack, the Pro Canoe / Kayak Carrier can be
mounted to the left or right side, overhanging
the rack as shown. (Refer to Step 2.5)
Adjust one arm of the Carrier up or down as
required, aligning the hole on the outside of
the Carrier with one of the five adjustment
holes on the inside of the Carrier.
Fasten the Carrier in position using M6 x 25
Button Bead and M6 Nyloc Nuts
(Items 5 & 6) as shown removed earlier.
Place M6 Nut Caps (Item 7) over the Nyloc
Nuts.
Secure your Kayak/Canoe using the
Stratchits (Item 8) supplied. The Carabiners
are attached to the Carriers on one of the
cross bars as indicated or by using the M8
Eye Nuts, M8 Nylon Washers and M8 x 16
Hex Bolts and fixing them in a suitable
T-slot on your Rack.
6
7
5
4mm
10mm
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Front Runner
Front Runner
Front Runner RRAC105 Manual de usuario
Front Runner
Front Runner LAMS004 Manual de usuario
Front Runner
Front Runner 200 Series Manual de usuario
Front Runner
Front Runner TBMK009 Manual de usuario
Front Runner
Front Runner MKIII Small Manual de usuario
Front Runner
Front Runner FAJK010 Manual
Front Runner
Front Runner RRAC119 Manual de usuario
Front Runner
Front Runner SLIMLINE II Instrucciones de montaje
Front Runner
Front Runner KRTT001T Manual de usuario
Front Runner
Front Runner LATF002 Manual de usuario
Front Runner
Front Runner SSBS008 Manual de usuario
Front Runner
Front Runner RRAC210 Manual de usuario
Front Runner
Front Runner SLIMLINE II TRAY Manual de usuario
Front Runner
Front Runner FATT002 Manual de usuario
Front Runner
Front Runner SSDS113 Manual de usuario
Front Runner
Front Runner SLIMLINE II Manual de usuario
Front Runner
Front Runner Slimline II KRKS007T Manual de usuario
Front Runner
Front Runner RRAC190 Manual de usuario
Front Runner
Front Runner TRCA009 Manual de usuario
Front Runner
Front Runner TRCA010 Manual de usuario
