Flying Industry Development S1UD-DC06 Manual de usuario

SHENZHENGUIYUANINDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

RF Wireless Remote Control Radio Controller with Delay Time Function / Transmitter & Receiver

Package Include:

1 x Receiver: S1UD-DC06 / S1UD-DC09 / S1UD-DC12 / S1UD-DC24 (1 Channel/ Three Control Modes)

2 x Transmitter: C-2

1 x User manual

Feature:

Wireless control, easy to install

Setting delay time from0 to 99 seconds.

Control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with voltage AC110~240V or

DC0~28V.

You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass

throughwalls,floors and doors.

With characteristics of reverse power protection.

Use an 8-bit microcontroller with low-power and high-speed CMOS technology.

Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bitcode.

One/ several transmitters can control one/several receivers simultaneously.

If you use two or more receivers in thesame place, youcanset themwithdifferentcodes.

Transmitting Frequency: 315MHz / 433MHz

Receiver:

Model No.: S1UD-DC06 / S1UD-DC09 / S1UD-DC12 / S1UD-DC24

Channel: 1 CH

Control Modes: Toggle, Momentary, Latched

Delay time: 0~99 seconds

Coding Type: Fixed code or Learningcode

Coding Setting: By learning

Power Supply (Operating Voltage): DC6V (S1UD-DC06), DC12V±1V (S1UD-DC12), DC9V±1V (S1UD-DC09), DC24V±2V (S1UD-DC24)

Working Voltage Range of Relay:AC110~240V or DC0~28V

Output: Relay output (Normally open and normally closed)

MaximumWorking Current of Relay: 7A

PCB Size: 45mmx 30mmx 15mm

Case Size: 50mmx 35mmx 23mm

Receiver Sensitivity:-114dbm

Static Current: ≤10mA

Transmitter:

Model No.: C-2

Channel: 2 CH

Remote Control Distance: 100m/ 300ft (theoretically)

Encode: Fixed code by soldering

Unit size: 58mmx 39mmx 16mm

Power Supply: 1x 23A -12V battery (included,can be usedfor 12 months)

Usage:

Initial state: Terminals A, B = Normally Closed; Terminals B, C = Normally Open.

Connect device to terminal “B & C”; connect power supply to terminal “+” and “-”.

Setting differentcontrol modes (We haveset the receiver as Toggle control mode before delivery. If youwant to use other control modes, do as

followingoperation):

Setting controlmode Toggle: Connect Jumper-2 and Jumper-3.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on therelay (connect B and C, disconnectA and B)

Press button 1 again: Turn off therelay(disconnect B and C, connectA and B)

If youset delay time, such as 30 seconds:

Press button 1: Turn on therelay(connect B and C, disconnectA and B)

After 30seconds, Turn off the relay automatically (disconnect B and C, connectAand B). Orpress button 1 againwithin 30seconds:Turn off the

relay immediately.

Setting controlmode Momentary: Disconnect Jumper.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1:Turn on therelay(connect B and C, disconnectA and B)

Release button 1: Turn off the relay (disconnect B and C, connectA and B)

If youset delay time, such as 20 seconds:

Press and hold button 1:Turn on therelay(connect B and C, disconnectA and B)

After 20 seconds, Turn off the relay automatically (disconnect B and C, connect A and B). And the relay couldn’t be turned off by pressing any

buttonw ithin 20seconds.

SHENZHENGUIYUANINDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

Setting controlmode Latched: Connect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button-> Off.

Press button 1: Turn on therelay (connect B and C, disconnectA and B)

Press button 2: Turn off therelay (disconnect B and C, connectA and B)

If youset delay time, such as 10 seconds:

Press button 1: Turn on therelay (connect B and C, disconnectA and B)

After 10 seconds, Turnoff the relay automatically (disconnect B and C, connect Aand B). Or press button 2within 10seconds: Turn off the relay

immediately.

Delay timesetting function:

Press thesetting button, the LEDoff, that means enter into the delay time setting mode.

Then you canset delay time through pressing the learn button. Press the learn button, LEDwill flash once, that means the delay time increase1

seconds, if youwant todelay 30seconds,you need to press the learn buttonwith 30 times.

Youcanset longest delay time to 99 seconds.

Press the setting button again, the delay time what you have setwill be preserved forever even if you turn off power. After the delay time is

preserved by the system, LEDwill flash 3 times, the systemwill quit the delay time setting mode.

For example,when you use this receiver to control one lamp, and you already set 30 seconds delay time, you can press button 1 to turn on the

lamp, and the lampwill turn off automatically after 30seconds. If you don’t need the delay function,youshould clear the delay time.

Clear delaytime:

If you don’t w ant toset thedelay time, you can operate as following:

Press thesetting button and enter into the delay time setting mode, the delay timewhatyou havesetwill be cleared automatically.

Press thesetting button again, LED will flash 3 times, the systemw ill quit the delay time setting mode.

Note:

We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control,you can delete all codes of remote

controls,whicharestored in thereceiver.

Operation: Press and hold the learn button of receiver until LED begin flashes slowly; release the button, LEDkeeps slow flash. That means all

storedcodes have been deletedsuccessfully.

Learning the button of remote control:

1) Press thelearn button of receiver, LEDoff. The receiver enters into statusof LEARNING.

2) Press any one button on remote control. If LEDflashes 3 times and turns off, it means learning is successful.

3) When receiver is in the status of LEARNING, you should learn the remote control within 10 seconds, or the receiver will quit the status of

LEARNING after 10seconds.

4) The receivercan learn 16 remote controlswith differentcodes.

Interior Analogue Circuit

Application: For DC12V motor or lamp

DC0~28V/ AC110~240V

Application Circuit

Power supply

A, B=Normally Closed; B, C=Normally Open.

Lamp

Relay

Learn Button

LED

Antenna

RF module

LED

Setting Button

Jumper

Learn Button

Setting Button

Antenna

RF module

Power supply

Motor

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mando a distancia de Flying Industry Development

Flying Industry Development

Flying Industry Development S2PX-DC09-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development S1X2-DC Manual de usuario

Flying Industry Development

Flying Industry Development 0021112 Manual de usuario

Flying Industry Development

Flying Industry Development S1XB-AC220-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development 0020167 Manual de usuario

Flying Industry Development

Flying Industry Development 0020027 Manual de usuario

Flying Industry Development

Flying Industry Development S1F2-DC06 Manual de usuario

Flying Industry Development

Flying Industry Development 0020080 Manual de usuario

Flying Industry Development

Flying Industry Development S1PX-DC-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development S4PUA-AC220 Manual de usuario

Flying Industry Development

Flying Industry Development S1XB-DC06 Manual de usuario

Flying Industry Development

Flying Industry Development 4S1PFC-AC220+CV-8-3 Manual de usuario

Flying Industry Development

Flying Industry Development 0020703 Manual de usuario

Flying Industry Development

Flying Industry Development S2T-DC06-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development 0020794 Manual de usuario

Flying Industry Development

Flying Industry Development S2U-DC06-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development 00200261 Manual de usuario

Flying Industry Development

Flying Industry Development 0020210 Manual de usuario

Flying Industry Development

Flying Industry Development 0020130 Manual de usuario

Flying Industry Development

Flying Industry Development S1F2-DC06 Manual de usuario

Flying Industry Development

Flying Industry Development S2T-DC06-ANT1 Manual de usuario

Flying Industry Development

Flying Industry Development S1T-AC110 Manual de usuario

Flying Industry Development

Flying Industry Development S1PS1-DC06-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development 6S2UB-DC12+1CV-12 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación