Flying Industry Development 0020481 Manual de usuario

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

RF Wireless Remote Control Kit (Model 0020481)

Package Include:

1 x Receiver: S2PF-DC06 / S2PF-DC09 / S2PF-DC12 / S2PF-DC24

1 x Transmitter: CV-6-2

1 x User manual

Features:

Application: It can be used in rolling blinds, rolling doors, projection screens, awnings, pumps, winches, conveyors or other appliances and

equipments with DC motors, it can remote control DC motor rotates in the positive or reversal direction.

Wireless control, easy to install.

Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.

You can rotate two motors separately in the positive or reversal direction with the transmitter (remote control) from any place within a reliable distance.

The RF wireless signal can pass through walls, floors and doors.

High Power: Each channel can work at maximum current 30A.

With limit control terminals: You can connect limit switches or sensors to stop the motor.

With wired control terminals: You can connect manual switches or external devices (with low level output signal, such as sensors) to control the

motor.

Use an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.

With characteristics of reverse power protection and over current protection.

Reliable control: The receiver only works with the transmitter which use same code.

One/several transmitters can control one/several receivers simultaneously.

You can use two or more units in the same place.

Receiver Parameters:

Model No: S2PF-DC06 / S2PF-DC09 / S2PF-DC12 / S2PF-DC24

Control Mode: Latched or Momentary

Coding Type: Fixed code or learning code

Coding Setting: By learning

Power Supply (Operating Voltage): DC6V (S2PF-DC06), DC9V±1V (S2PF-DC09), DC12V±1V (S2PF-DC12), DC24V±1V (S2PF-DC24)

Output: DC6V (S2PF-DC06), DC9V (S2PF-DC09), DC12V (S2PF-DC12), DC24V (S2PF-DC24)

Working Frequency: 315MHz / 433MHz

Channel: 2 CH, can work with 2 DC motors

Static Current: ≤6mA

Maximum Working Current: 30A / each channel, so motor's maximum starting current can not exceed 30A.

PCB Size: 170mm x 109mm x 25mm

Case Size: 200mm x 120mm x 53mm

Note:

1. The receiver can work with different transmitters. When you set the receiver in momentary mode, it should work with four button transmitters, such

as model C-4 (100M), CWB-4 (50M, waterproof), CP-4 (500M), CV-4-2 (500M), or CB-4 (1000M) etc. When you set the receiver in latched mode, it

should work with six button transmitters, such as model CP-6 (500M), CV-6-2 (500M), or CB-6 (1000M) etc.

2. With a transmitter (such as CV-6-2) to form a complete set, the working distance can reach 500M in an open ground. The maximum working

distance 500M is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by

trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may or may not reach 500M. If you

want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB

transmitters.

Transmitter Parameters:

Model No.: CV-6-2

Button: 6

Remote Control Distance: 500m / 1500ft (theoretically)

Encode: Fixed code by soldering

Unit Size: 110mm x 50mm x 18mm

Power Supply: 1 x 23A -12V battery (included, can be used for 12 months)

Usage (with transmitter CV-6-2):

Connect the positive pole of DC power supply to terminal “+” of INPUT, and connect the negative pole of DC power supply to terminal “-”of INPUT.

Connect terminals “A1”and “B1”to motor 1; connect terminals “A2”and “B2”to motor 2. You can exchange motor's two wires to change the rotating

direction of motor.

Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)

Press button ▲on the left: motor 1 rotates in positive direction.

Press button ▼on the left: motor 1 rotates in reversal direction.

Press button ■on the left: motor 1 stops.

Press button ▲on the right: motor 2 rotates in positive direction.

Press button ▼on the right: motor 2 rotates in reversal direction.

Press button ■on the right: motor 2 stops.

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

Setting control mode Momentary: Only connect Jumper-1 (CN1)

Press and hold button ▲on the left: motor 1 rotates in positive direction. Release button ▲on the left: motor 1 stops.

Press and hold button▼on the left: motor 1 rotates in reversal direction. Release button ▼on the left: motor 1 stops.

Press and hold button ▲on the right: motor 2 rotates in positive direction. Release button▲on the right: motor 2 stops.

Press and hold button▼on the right: motor 2 rotates in reversal direction. Release button ▼on the right: motor 2 stops.

Limit control terminals:

Limit control terminals S1, S2, S3 and S4 are normally open, you can connect limit switches or sensors (normally open type) to terminals S1, S2, S3

and S4, and then you can use limit switches or sensors to stop the motor.

When motor 1 rotates in positive direction, if connect two terminals of S1, the motor 1 will stop automatically.

When motor 1 rotates reversal direction, if connect two terminals of S2, the motor 1 will stop automatically.

When motor 2 rotates in positive direction, if connect two terminals of S3, the motor 2 will stop automatically.

When motor 2 rotates reversal direction, if connect two terminals of S4, the motor 2 will stop automatically.

Wired control terminals:

You can connect manual switches, external devices or sensors (with low level output signal) to control the motor.

1) The manual switches:

You can connect manual switches to terminals “Signal-”, “Signal 1+”, “Signal 2+”, “Signal 3+”, “Signal 4+”, then you can use manual switches to

control the motor.

When connect terminals “Signal 1+”and “Signal-”, motor 1 rotates in positive direction.And when disconnect “Signal 1+”and “Signal-”, motor 1 stops.

When connect terminals “Signal 2+”and “Signal-”, motor 1 rotates in reversal direction. And when disconnect “Signal 2+”and “Signal-”, motor 1

stops.

When connect terminals “Signal 3+”and “Signal-”, motor 2 rotates in positive direction.And when disconnect “Signal 3+”and “Signal-”, motor 2 stops.

When connect terminals “Signal 4+”and “Signal-”, motor 2 rotates in reversal direction. And when disconnect “Signal 4+”and “Signal-”, motor 2

stops.

2) Signal input:

You can connect external devices (with low level output signal) to terminals “Signal-”, “Signal 1+”, “Signal 2+”, “Signal 3+”, “Signal 4+”, then the

external device’s output signal can control the motor.

When the external device outputs low level signal to terminal “Signal-”and “Signal 1+“, motor 1 rotates in positive direction.

When the external device outputs low level signal to terminal “Signal-”and “Signal 2+“, motor 1 rotates in reversal direction.

When the external device outputs low level signal to terminal “Signal-”and “Signal 3+“, motor 2 rotates in positive direction.

When the external device outputs low level signal to terminal “Signal-”and “Signal 4+“, motor 2 rotates in reversal direction.

How to pair the transmitter to the receiver:

1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.

2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.

3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.

4) The receiver can learn several remote controls with different codes.

Delete all transmitters:

We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote

controls, which are stored in the receiver.

Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored

codes have been deleted successfully.

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

CN1

CN2

Control DC Motor

Power LED

Relay 1

Relay 4

Relay 2

Relay 3

Status LED 2

Status LED 3

Status LED 4

Status LED 1

External Device

Signal 1+

Signal 2+

Signal 3+

Signal 4+

Signal -

RF module

Antenna

Signal LED

Learning Button

Limit Terminals

DC Power Supply

Motor 1

Motor 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mando a distancia de Flying Industry Development

Flying Industry Development

Flying Industry Development S4PUA-AC220 Manual de usuario

Flying Industry Development

Flying Industry Development S2T-DC06-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development 0020794 Manual de usuario

Flying Industry Development

Flying Industry Development 6S2UB-DC12+1CV-12 Manual de usuario

Flying Industry Development

Flying Industry Development 0020703 Manual de usuario

Flying Industry Development

Flying Industry Development 3S2UB-DC12+CV-6 Manual de usuario

Flying Industry Development

Flying Industry Development S1PX-DC-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development 0020210 Manual de usuario

Flying Industry Development

Flying Industry Development S1PF3-DC12 Manual de usuario

Flying Industry Development

Flying Industry Development S1DA-DC09 Manual de usuario

Flying Industry Development

Flying Industry Development 15S1PXB-DC12+1CP-15 Manual de usuario

Flying Industry Development

Flying Industry Development 0021112 Manual de usuario

Flying Industry Development

Flying Industry Development S1F2-DC06 Manual de usuario

Flying Industry Development

Flying Industry Development S1T-AC110 Manual de usuario

Flying Industry Development

Flying Industry Development S1PF-DC12 Manual de usuario

Flying Industry Development

Flying Industry Development S1X-DC06 Manual de usuario

Flying Industry Development

Flying Industry Development S1F2-DC06 Manual de usuario

Flying Industry Development

Flying Industry Development 0020109 Manual de usuario

Flying Industry Development

Flying Industry Development S2T-DC06-ANT1 Manual de usuario

Flying Industry Development

Flying Industry Development S1X2-DC Manual de usuario

Flying Industry Development

Flying Industry Development S1PS1-DC06-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development 00200261 Manual de usuario

Flying Industry Development

Flying Industry Development S1XB-DC06-ANT2 Manual de usuario

Flying Industry Development

Flying Industry Development S2U-DC06-ANT2 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación