EtherWAN EX63000 Series Manual de usuario
Copyright 2018 EtherWAN Systems, Inc. Page 1
All Rights Reserved
EX63000
4/16/2018
W70G-EX630V2Q1
1 Unpacking
Unpack the items. Your package should include:
One EX63000 Series hardened managed switch
If items are missing or damaged, notify your
EtherWAN representative. Keep the carton and
packing material. The full product manual can be
downloaded from:
https://www.etherwan.com/support/product/ex6
3000-series
2 Equipment Needed
Appropriate cables for data ports
Personal computer or laptop
3 Select a Location
Installation: DIN rail, wall mount, rack, or
cabinet.
Identify a power source within 6 ft. (1.8m).
Choose a dry area with ambient temperature
between -10 and 60°C (14 and 140ºF).
Be sure there is adequate airflow.
Keep the switch at least 6 ft. (1.83m) away from
the nearest source of electromagnetic noise,
such as a photocopy machine.
Switch is designed for use in Pollution Degree 2
Environment.
4 Connect to the Data Ports
Depending on the model, your switch can have the
following ports:
16 10/100Base-TX ports
0 or 2 Gigabit ports
10/100Base-TX Ports
These ports come in 10/100Base-TX interfaces. They
can connect to devices such as an IP surveillance
camera or a Voice over Internet Protocol (VoIP)
phone.
Gigabit Ports
Some switch models have 10/100/1000Base-TX
ports with no Gigabit fiber ports, or combo
10/100/1000Base-TX with 1000Base-SX/LX/BX
ports. You can connect these ports to network
devices such as a computer, printer, network video
recorder (NVR), network storage, or they can
connect to the network itself.
Combo ports on the bottom face operate in
“either/or” fashion. This means that attaching to a 1
Gbps combo port renders the equivalent partner
combo port unavailable.
EX63000 Series Hardened Managed Switch
Installation Guide
Combo Ports
EX63000 Managed Switch Installation Guide
Copyright 2018 EtherWAN Systems, Inc. Page 2
All Rights Reserved
EX63000
4/16/2018
W70G-EX630V2Q1
5 Apply Power
The switch has a 12-48VDC terminal block. Only one
power input is required to operate the switch.
However, redundant power supply functionality is
supported.
Terminal Block
The switch provides two power inputs on a 12-
48VDC terminal block. Only one power input is
required to operate the switch. The terminal block
has 5 terminal posts.
Pin Description
Power 2 +12-48VDC
−Power Ground
Power 1 +12-48VDC
−Power Ground
Earth Ground
Relay Output Rating 0.6A @ 30VDC
Power-Up Sequence
When you apply power, all Link/ACT LEDs will light
up, and stay lit as the device boots up. When the
boot process is finished, only LEDS next to
connected ports will stay lit.
The Power 1/2 LEDs will light up to show the
connected power inputs.
Relay Output
The switch id equipped with a 3-point relay output.
Current is 30VCD / 0.6A
Relay Status
Normally closed
Normally Open
No Power
Closed
Open
Normal
Open
Closed
Abnormal
Closed
Open
6 Front Panel LEDs
LED Color Status
Power 1
Power 2 Green ON = power on.
OFF = power off.
10/100Base-TX LEDs
LED Color Status
Link/Act Green
ON = valid network connection is
established.
Flashing = port sending or receiving data.
10/100/1000Base-TX LEDs
Link/Act Green
ON = valid network connection is
established.
Flashing = port sending or receiving data.
1000Base-SX/LX/BX LEDs
Link/Act Orange
ON = valid network connection is
established.
Flashing = port sending or receiving data.
7 Managing the Switch
A. Connect a PC to an available switch port using
an appropriate cable.
B. Confirm that the Link/ACT LED for the switch
port to which the PC is connected is ON. If not,
choose a different port.
C. Configure the PC’s TCP/IP settings to use the
subnet 192.168.1.Xand subnet mask
255.255.255.0, where Xis a number from 2 to
254 other than 10.
D. In a Web browser address bar, type
http://192.168.1.10 and press Enter.
E. Log in to the management interface.
F. By default there is no password assigned to the
switch. To add a password:
- Click in the Password text box, enter a
password, and retype it in the Retype
Password text box.
- Click Update Setting below the Retype
Password text box.
Este manual sirve para los siguientes modelos
2
Otros manuales de Cambiar de EtherWAN
EtherWAN
EtherWAN EX78000 Series Manual de usuario
EtherWAN
EtherWAN ER58000 Series Manual de usuario
EtherWAN
EtherWAN ER59000 Series Manual de usuario
EtherWAN
EtherWAN EX19162A Manual de usuario
EtherWAN
EtherWAN EX77964 Manual de usuario
EtherWAN
EtherWAN EX78600 Manual de usuario
EtherWAN
EtherWAN EX78900X Series Manual de usuario
EtherWAN
EtherWAN EX42000 Series Manual de usuario
EtherWAN
EtherWAN EX33000 Series Manual de usuario
EtherWAN
EtherWAN EX87000 Series Manual de usuario
EtherWAN
EtherWAN EX46910F Manual de usuario
EtherWAN
EtherWAN EX25611 Manual de usuario
EtherWAN
EtherWAN EX76000 Series Manual de usuario
EtherWAN
EtherWAN EX75000 Manual de usuario
EtherWAN
EtherWAN EX72000 Manual de usuario
EtherWAN
EtherWAN EX17082A Manual de usuario
EtherWAN
EtherWAN EX42905 Series Manual de usuario
EtherWAN
EtherWAN EX73000 Series Manual de usuario
EtherWAN
EtherWAN EX75900 Series Manual de usuario
EtherWAN
EtherWAN EX17908 Series Manual de usuario
