EtherWAN EX43000 series Manual de usuario

W70G-EX43000Q1 Page 1

Installation Guide

EX43000 Series | Industrial Unmanaged Switch

1Unpacking

Open the carton and unpack the items. Your package

should include:

▪One EX43000 Switch

▪DIN rail mounting kit

If any items are missing or damaged, notify your

EtherWAN representative. If possible, save the carton

and packing material in case you need to ship or store

the switch in the future.

2Equipment Needed

▪Category 5 or better cable for RJ-45 ports

▪Appropriate fiber cable for fiber ports

3Select a Location

▪Installation: DIN rail. Place the device on the DIN

rail from above using the slot. Push the front of

the device toward the mounting surface until it

audibly snaps into place.

▪Choose a dry area with ambient temperature

between -20°C and 60°C (-4°F and 140°F).

▪Keep away from heat sources, sunlight, warm air

exhausts, hot-air vents, and heaters.

▪Be sure there is adequate airflow.

4Connect to the Data Ports

Depending on the model, your switch can have the

following ports:

▪4, 6, or 8 10/100Base-TX ports

▪0, 1, 2, or 4 100Base-FX ports

5Connect Power

Terminal Block

The switch provides two power inputs on a 12-48VDC

terminal block. Only one power input is required to

operate the switch. The terminal block has 5 terminal

posts.

Description

Power 2

12-48VDC

−

Power Ground

Power 1

12-48VDC

−

Power Ground

Earth Ground

Relay Output

Rating

0.6A @ 30VDC

Power Failure Alarm

There are three pins on the terminal block are used for

power failure detection. It provides the normally open

or closed output when the power source is active. Use

this as a dry contact application to send a signal for

power failure detection.

Power-Up Sequence

When the switch is powered up:

▪All Link/ACT LEDs blink momentarily.

▪The Power LED lights up and stays lit.

▪LEDs for every port connected to a device will

flash, as the switch conducts a brief Power On Self-

Test (POST).

6LED Indicators

W70G-EX43000Q1 Page 2

Installation Guide

EX43000 Series | Industrial Unmanaged Switch

LED

State

Description

Power 1, 2

(Green)

Switch is powered ON

correctly

Off

Switch is not receiving power

Fault (Red)

Relay alarm on

Off

Relay alarm off

10/100Base TX or 100Base FX Ports

Link/Act

(Green)

Network connection

established

Off

No link

Blinking

Transmitting or receiving

data

7Set DIP Switches

The switch has a 10-position DIP switch that controls

the alarm status on each port. Alarms are sent

through the relay output.

DIP

Switch

Setting and Description

ON = Port 1 Alarm is enabled.

OFF = Port 1 Alarm disabled

ON = Port 2 Alarm is enabled.

OFF = Port 2 Alarm disabled

ON = Port 3 Alarm is enabled.

OFF = Port 3 Alarm disabled

ON = Port 4 Alarm is enabled.

OFF = Port 4 Alarm disabled

ON = Port 5 Alarm is enabled.

OFF = Port 5 Alarm disabled

ON = Port 6 Alarm is enabled.

OFF = Port 6 Alarm disabled

ON = Port 7 Alarm is enabled

OFF = Port 8 Alarm disabled

ON = Port 8 Alarm is enabled

OFF = Port 8 Alarm disabled

ON = Broadcast storm protection

enabled

OFF = Broadcast storm protection

disabled

Reserved

8DIN Rail Installation

DIN-Rail Assembly Startup, and Dismantling

▪Assembly: Place the Switch on the DIN rail from

above using the slot. Push the front of the Switch

toward the mounting surface until it audibly snaps

into place.

▪Startup: Connect the supply voltage to start up the

Switch via the terminal block.

▪Dismantling: Pull out the lower edge and then

remove the Switch from the DIN rail.

Manufacturer information:

EtherWAN Systems, Inc.

33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New

Taipei City, 221 Taiwan

The full product manual can be downloaded from:

www.etherwan.com

Otros manuales para EX43000 series

Otros manuales de Cambiar de EtherWAN

EtherWAN

EtherWAN EX42008 Series Manual de usuario

EtherWAN

EtherWAN EX46910F Manual de usuario

EtherWAN

EtherWAN EX72129A Manual de usuario

EtherWAN

EtherWAN EG97000 Series Manual de usuario

EtherWAN

EtherWAN EX16908 Manual de usuario

EtherWAN

EtherWAN EX17082A Manual de usuario

EtherWAN

EtherWAN EX77900 Series Manual de usuario

EtherWAN

EtherWAN EX19164A Manual de usuario

EtherWAN

EtherWAN EX26262F Series Manual de usuario

EtherWAN

EtherWAN EX26262F Manual de usuario

EtherWAN

EtherWAN EX75900 Series Manual de usuario

EtherWAN

EtherWAN EX78900 Series Manual de usuario

EtherWAN

EtherWAN InfraGreEn IG5 Manual de usuario

EtherWAN

EtherWAN EX46900A Series Manual de usuario

EtherWAN

EtherWAN EX17242 Manual de usuario

EtherWAN

EtherWAN EX87000 Series Manual de usuario

EtherWAN

EtherWAN EX42300 series Manual de usuario

EtherWAN

EtherWAN EX17008 Manual de usuario

EtherWAN

EtherWAN EX1624W Manual de usuario

EtherWAN

EtherWAN EX29000 Manual de usuario

EtherWAN

EtherWAN EX78162 Series Manual de usuario

EtherWAN

EtherWAN EX73900X Series Manual de usuario

EtherWAN

EtherWAN EX27000 Series Manual de usuario

EtherWAN

EtherWAN EX17162 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario